Instrukcja obsługi Makita DCO180Z

Makita maszyna do cięcia DCO180Z

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Makita DCO180Z (12 stron) w kategorii maszyna do cięcia. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
1
ENGLISH (Original instructions)
INSTRUCTION MANUAL
IMPORTANT: Read Before Using.
Cordless Cut-Out Tool
DCO140
DCO180
014848
2
ENGLISH (Original instructions)
SPECIFICATIONS
Model DCO140 DCO180
Collet chuck capacity 3 mm, 6 mm or 1/8", 1/4" 3 mm, 6 mm or 1/8", 1/4"
Rated speed (n)/ No load speed (n
0) 30,000 min-1 30,000 min-1
Overall length 313 mm 313 mm
Net weight 1.6 kg 1.7 kg
Rated voltage D.C. 14.4 V D.C. 18 V
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications and battery cartridge may differ from country to country.
• Weight, with battery cartridge, according to EPTA-Procedure 01/2003
END004-6
Symbols
The following show the symbols used for the equipment.
Be sure that you understand their meaning before use.
･ Read instruction manual.
･ Only for EU countries
Do not dispose of electric equipment or
battery pack together with household
waste material!
In observance of the European
Directives, on Waste Electric and
Electronic Equipment and Batteries and
Accumulators and Waste Batteries and
Accumulators and their implementation
in accordance with national laws,
electric equipment and batteries and
battery pack(s) that have reached the
end of their life must be collected
separately and returned to an
environmentally compatible recycling
facility.
ENE012-1
Intended use
The tool is intended for cutting gypsum, wood, plastic
and soft wall tiles.
ENG905-1
Noise
The typical A-weighted noise level determined
according to EN60745:
Sound pressure level (L
pA) : 77 dB (A)
Uncertainty (K) : 3 dB (A)
The noise level under working may exceed 80 dB (A).
Wear ear protection
ENG900-1
Vibration
The vibration total value (tri-axial vector sum)
determined according to EN60745:
Work mode : rotation without load
Vibration emission (ah) : 2.5 m/s2 or less
Uncertainty (K) : 1.5 m/s2
ENG901-1
• The declared vibration emission value has been
measured in accordance with the standard test
method and may be used for comparing one tool
with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the
power tool can differ from the declared emission
value depending on the ways in which the tool is
used.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
ENH101-17
For European countries only
EC Declaration of Conformity
Makita declares that the following Machine(s):
Designation of Machine:
Cordless Cut-Out Tool
Model No./ Type: DCO140, DCO180
Conforms to the following European Directives:
2006/42/EC
They are manufactured in accordance with the following
Standard or standardized documents:
EN60745
The Technical file in accordance with 2006/42/EC is
available from:
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
Cd
Ni-MH
Li-ion
3
27.9.2013
000331
Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
GEA006-2
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.
Work area safety
1. Keep work area clean and well lit. Cluttered or
dark areas invite accidents.
2. Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.
Electrical safety
4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce risk of electric shock.
5. Avoid body contact with earthed or grounded
surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of
electric shock if your body is earthed or grounded.
6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.
7. Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords
increase the risk of electric shock.
8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use
of a cord suitable for outdoor use reduces the risk
of electric shock.
9. If operating a power tool in a damp location is
unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an
GFCI reduces the risk of electric shock.
Personal safety
10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while
operating power tools may result in serious
personal injury.
11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
12. Prevent unintentional starting. Ensure the
switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools
with your finger on the switch or energising power
tools that have the switch on invites accidents.
13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key
left attached to a rotating part of the power tool
may result in personal injury.
14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.
15. Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,
jewellery or long hair can be caught in moving
parts.
16. If devices are provided for the connection of
dust extraction and collection facilities,
ensure these are connected and properly
used. Use of dust collection can reduce dust-
related hazards.
Power tool use and care
17. Do not force the power tool. Use the correct
power tool for your application. The correct
power tool will do the job better and safer at the
rate for which it was designed.
18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that
cannot be controlled with the switch is dangerous
and must be repaired.
19. Disconnect the plug from the power source
and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

Specyfikacje produktu

Marka: Makita
Kategoria: maszyna do cięcia
Model: DCO180Z

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Makita DCO180Z, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje maszyna do cięcia Makita

Makita

Makita WST05 Instrukcja

20 Września 2024
Makita

Makita UR101CZ Instrukcja

11 Września 2024
Makita

Makita CC301DZ Instrukcja

5 Września 2024
Makita

Makita DSC102ZJ Instrukcja

1 Września 2024
Makita

Makita DSC251ZK Instrukcja

31 Sierpnia 2024
Makita

Makita DCO180Z Instrukcja

30 Sierpnia 2024
Makita

Makita DUR368APG2 Instrukcja

5 Lipca 2024
Makita

Makita SD100DZ Instrukcja

4 Lipca 2024

Instrukcje maszyna do cięcia

Najnowsze instrukcje dla maszyna do cięcia

Royal Catering

Royal Catering RCAM-250E Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCAM-250PRO Instrukcja

14 Października 2024
Royal Catering

Royal Catering RCAM-250EXPERT Instrukcja

14 Października 2024
Princess

Princess Classic Multi Food Slicer 492977 Instrukcja

10 Października 2024
Melissa

Melissa 16220009 Instrukcja

9 Października 2024
Severin

Severin AS 3914 Instrukcja

9 Października 2024
Graef

Graef S52200 Instrukcja

8 Października 2024
Cigweld

Cigweld COMET Instrukcja

8 Października 2024
RGV

RGV Luxury 25 Instrukcja

8 Października 2024
Weston

Weston 36-3551-W Instrukcja

8 Października 2024