Instrukcja obsługi M-System MVK-90

M-System Okap wyciągowy MVK-90

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla M-System MVK-90 (16 stron) w kategorii Okap wyciągowy. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/16
INSTRUCTIONS FOR USE
GEBRAUCHSANWEISUNG
INSTRUCTIONS POUR L'EMPLOI
ISTRUZIONI PER L'USO
INSTRUCCIONES PARA EL USO
GEBRUIKSAANWIJZING
WARNING
-----------------------------------------------------------
The distance between the supporting surface for the
cooking vessels on the hob and the lower part of the
hood must be at least 65 cm. If the instructions for
installation for the hob specify a greater distance, this
has to be taken into account.
The air collected must not be conveyed into a duct used
to blow off smokes from appliances fed with an energy
other than electricity (central heating systems,
thermosiphons, water-heaters, etc.).
Comply with the official instructions provided by the
competent authorities in merit when installing the disposal
duct. In addition, exhaust air should not be discharged
into a wall cavity, unless the cavity is designed for that
purpose.
The room must be well aerated in case a hood and some
other heat equipment fed with an energy other than
electricity (gas, oil, coal heaters, etc) operate at the
same time. In fact the intake hood, disposing of air,
could create a vacuum in the room. The vacuum should
not exceed 0,04mbar. This prevents the gas exhausted
by the heat source from being intaken again. It is
therefore advisable to ensure the room contains air
taps able to ensure a steady flow of fresh air.
Check the data label inside the appliance; if the
symbol ( ) is printed, read the following: this
appliance has such technical particulars that it
belongs to class II insulation, therefore it must not
be earthed.
The following warning is valid in the United Kingdom
only: in case your cable is not furnished with a plug,
read the following instructions; as the colours of the
wires in the mains lead of this appliance may not
correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
– the wire which is coloured blue must be connected
to the terminal which is marked with the letter N or
coloured black;
– the wire which is coloured brown must be connected
to the terminal which is marked with the letter L or
coloured red.
– terminal of a three-pin plug.
Check the data label inside the appliance; if the
symbol ( ) is NOT printed, read the following:
ATTENTION: This appliance must be grounded. When
making the electrical connections, check that the
current socket has a ground connection.
The following warning is valid in the United Kingdom
only: as the colours of the wires in the mains lead of
this appliance may not correspond with the coloured
markings identifying the terminals in your plug, proceed
as follows:
– the wire which is coloured green and yellow must
be connected to the terminal in the plug which is marked
with the letter E or by the earth symbol [ ], or coloured
green or green and yellow;
English
– the wire which is coloured blue must be connected
to the terminal which is marked with the letter N or
coloured black;
– the wire which is coloured brown must be connected
to the terminal which is marked with the letter L or
coloured red.
When making the electrical connections, check that
the voltage values correspond to those indicated on
the data plate inside the appliance itself. In case your
appliance is not furnished with a non separating flexible
cable and has no plug, or has not got any other device
ensuring omnipolar disconnection from the electricity
main, with a contact opening distance of at least 3 mm,
such separating device ensuring disconnection from
the main must be included in the fixed installation. If
your unit features a power lead and plug, position this
so the plug is accessible.
Always switch off the electricity supply before carrying
out any cleaning or servicing operations on the
appliance.
USE
-----------------------------------------------------------
Avoid using materials which could cause spurts of
flame (flambées) near the appliance.
When frying, take particular care to prevent oil and
grease from catching fire. Already used oil is especially
dangerous in this respect. Do not use uncovered
electric grates.
To avoid possible risks of fire always comply with the
indicated instructions when cleaning anti-grease grille
and when removing grease deposits from the appliance.
MAINTENANCE
-----------------------------------------------------------
Thorough servicing guarantees correct and long-lasting
operation.
Particular care must be paid to the grease grille which
must be periodically cleaned in relation to use (at least
once every two months). Remove the grease grille and
wash them either by hand or in the dishwasher using
neutral detergent.
Any fat deposits should be removed from the appliance
periodically depending on amount of use (at least every
2 months). Avoid using abrasive or corrosive products.
To clean painted appliances on the outside, use a cloth
dipped in lukewarm water and neutral detergent. To
clean steel, copper or brass appliances on the outside,
it is always best to use specific products, following the
instructions on the products themselves. To clean the
inside of the appliance, use a cloth (or brush) dipped
in denatured ethyl alcohol.
DESCRIPTION
-----------------------------------------------------------
The appliance can be used in both the filtering and ducting
version.
In the Filtering version (Fig. 1), the air and vapours conveyed
by the appliance are depurated by charcoal filter(s) and
recirculated around the room. ATTENTION: Using the hood
as a filtering one it is necessary to use the charcoal filter(s)
that purifies the air sent back into the room.
In the Ducting version (Fig. 2), cooking vapours and odours
are conveyed straight outside by a disposal duct which
passes through the wall/ceiling. Use of charcoal filter is
therefore unnecessary.
According to the model you have bought, the appliance can
include 1 or 2 motors. In the I motor version the flange for
the air to be exhausted has not got a central position, but
it is slightly on the left.
INSTALLATION
-----------------------------------------------------------
Before assembling, in order to manoeuvre the appliance
more easily, take off the grease grille (Fig. 3): pull the front
of the grille upwards; desinsert the back from its seat.
IMPORTANT: So as not to damage your product, during
installation USE ONLY THE SCREWS PROVIDED. Make
sure these are used as shown in the following instructions.
To compensate possible depth voids between the appliance
and the wall, a plastic SPACING BAR to be fixed at the
back of the appliance by means of the three screws A is
included (Fig.4). The 3 screws A to be used are contained
in the accessory bag attached to the plastic spacing bar.
Cut the spacing bar according to the distance to be
adjusted.
Assembly under a pensile cupboard
The following operations are essential for as-sembly:
– Install the wiring system
– Prepare the air venting hole if your appliance is to be
installed in the Ducting version.
Fixation as indicated in Fig. 5:
Using the relative template make the 4 necessary fixing
holes in the bottom of the cupboard and cut the air venting
hole.
Move the hood close to the bottom of the wall unit and then
connect the two units by means of the 4 self-tapping
screws supplied together with the appliance.
Fixation with brackets as in Fig. 6 (optional):
Take the two brackets (S) out of the accessory bag
together with the 8 screws provided. Fit the brackets to
the wall unit being careful to position these correctly; for
this operation use the 4 longer screws. At this point,
secure the appliance to the brackets using the 4 shorter
screws.
Ducting version: connect the flange of the hood with the air
venting hole made previously in the wall/ceiling by means
of an adequate tube. Make the electrical connection of the
hood by means of the power supply cable. Assemble the
grease grille with the hood, inserting it obliquely (making the
front side go upwards).
Filtering version: connect a proper pipe to the flange of the
hood so that the air is sent outside the pensile and sent back
into the room. Make the electrical connection of the hood
by means of the power supply cable. Set the charcoal filter
(Fig. 7A) inside the grease grille blocking it by means of the
2 supplied metal wires (F), as indicated in Fig. 7; the 2 metal
wires must be threaded into the relevant slots.
Assemble the grease grille with the hood, inserting it ob-
liquely (making the front side go upwards).
OPERATION
-----------------------------------------------------------
Controls (Fig. 8):
A = ON/OFF 1st speed switch
B = II speed switch
C = III speed switch
The motor is automatically ON or OFF by opening/
closing the truck (unless switch A is on 0). Opening
the truck the motor works according to last speed
registered.
D = Light switch:position A (automatic), the light are
automatically regulated ON or OFF by the opening/
closing of the truck. Position M (manual), the light is
on. Position 0, the light is off.
In case the hood is a filtering version one, it is necessary
to change the charcoal filter(s) according to utilization
about every six month. To remove the filter:
– open the truck pulling it first downwards, then towards
the front.
– take off the grease grille: pull the front of the grille
upwards; desinsert the back from its seat.
– take off the charcoal filter (A) from the inside of the
grease grille taking off the 2 metal wires F (Fig. 7) that
blocks it.
Light bulb
- If the fluorescent light or incandescent lamps need
changing, slacken the light cover by disconnecting the
screw and remove the bulb itself (Fig. 9). Replace with a bulb
of the same type.
- To change the rectangular halogen bulbs open the cover
and remove the bulb without touching it with bare hands
(Fig.10). Replace with a bulb of the same type.

Specyfikacje produktu

Marka: M-System
Kategoria: Okap wyciągowy
Model: MVK-90

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z M-System MVK-90, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Okap wyciągowy M-System

M-System

M-System MSPK951IX Instrukcja

6 Kwietnia 2025
M-System

M-System MSK651IX Instrukcja

11 Marca 2025
M-System

M-System MVK-90 Instrukcja

27 Stycznia 2025
M-System

M-System MSPK 761 IX Instrukcja

15 Października 2024
M-System

M-System EK-9 GALASSIA Instrukcja

29 Września 2024
M-System

M-System MU-50 Instrukcja

12 Września 2024
M-System

M-System MSPK 760 IX Instrukcja

9 Września 2024
M-System

M-System MSDK 660 Instrukcja

5 Września 2024
M-System

M-System MSPK 660 IX Instrukcja

5 Września 2024
M-System

M-System MSPK 1261 Instrukcja

5 Września 2024

Instrukcje Okap wyciągowy

Najnowsze instrukcje dla Okap wyciągowy

Atag

Atag shc 9 Instrukcja

9 Kwietnia 2025
Bosch

Bosch DWA067A50 Instrukcja

9 Kwietnia 2025
Bosch

Bosch DWK098E50 Instrukcja

9 Kwietnia 2025
AEG

AEG DK9160-W Instrukcja

9 Kwietnia 2025
Atag

Atag WS 9011 PC Instrukcja

9 Kwietnia 2025
AEG

AEG DPE5950G Instrukcja

9 Kwietnia 2025
Bosch

Bosch DWB091E59 Instrukcja

9 Kwietnia 2025
Hansa

Hansa OKP931TH Instrukcja

9 Kwietnia 2025
Smeg

Smeg CA9SRX Instrukcja

9 Kwietnia 2025
Oranier

Oranier Mendo Isola 90 Instrukcja

9 Kwietnia 2025