Instrukcja obsługi LYYT ISRF1

LYYT Kontroler ISRF1

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LYYT ISRF1 (2 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
ISRF1
IN-LINE WIRELESS CONTROLLER
FOR SINGLE COLOUR LED TAPE
Item ref: 153.796UK
User Manual
WARNING: This product intended for professional installation of single colour LED tape and should be is
connected by qualified personnel in accordance with electrical safety standards. Ensure that the rated load
indicated is not exceeded.
Installation
The IS 1 controller can be employed to control single colour LED tape operating from a RF
5-24Vdc power supply. Maximum short term current load is rated at 12A.
For constant full power output, it is advised to limit this to 6A load.
For Lyyt single colour LED tape (156.705-1 6. 68UK), is recommended to connect no 5 7 it
more than 3 5m tapes radially from the same controller. When connecting more than one x
5m tape in this way, it will be necessary to remove the connectors and strip the wires for DC
connec using termina strips. I is also advised to use bypass wiring instead o connecting tion l t f
end- -end to avoid noticeable voltage drop at the furthes end fro the powe supply. to t m r
153.796 User Manual UK
Remote control
1. POWER LED on / standby button
2. LIGHT switches from pattern to static light mode
3. 100% sets static light brightness to 100%
4. MODE+ steps upwards through modes
5. SPEED- reduces speed of pattern
6. MODE- steps downwards through modes
7. BRIGHT+ increases brightness
8. BRIGHT- decreases brightness
9. 50% sets static light brightness to 50%
10. 25% sets static light brightness to 25%
11. SPEED+ increases speed of pattern
Remove the clear tab from the handheld remote to engage the battery (replacement CR2025 button cell)
To switch LEDs on, press the POWER button (from standby, the last setting is resumed)
If there is no response from the handset, it may be necessary to pair the handset to the controller (see “ ” below)Pairing
MODE+ and - buttons step through the 8 preset programmes in sequence (shown below)
SPEED+ or - will alter the rate of change in the selected mode
LIGHT button overrides the pattern mode to give a static light setting
BRIGHT+ or - will change the brightness in static mode
Preset brightness can be jumped to via the 25%, 50% or 100% buttons
Press POWER to enter standby mode (all LEDs off)
Pairing : If the LED controller does not respond to the RF remote handset, disconnect DC power from the controller.
Reconnect the DC power to the controller and hold down the “100%” and “25%” buttons simultaneously.
The controller and handset should now be paired and the controller should respond to the handset.
Preset
Name
Description
1
Random Glow
Fade in and out at random brightness & intervals
2
Regular Glow
Fade between fully on and off at a regular rate
3
Half Glow
Fade between fully on and half-on at a regular rate
4
Flicker
Flash on and off at a fast regular rate
5
Offset Flash
Flash on and off with pause at a regular rate
6
Even Flash
Flash on and off evenly at a regular rate
7
SOS
3 short - 3 long - 3 short Morse Code flash sequence
8
Strobe
Very short burst at regular intervals
Specifications
Power supply
5-24Vdc, 12A (50% duty cycle) or 6A (100% duty cycle)
Remote control frequency
433MHz
Lead length (power input, LED output)
100mm
Connections
DC5521 connectors
Controller dimensions
42 x 13 x 5mm
Weight
4.8g
Disposal: The “Crossed Wheelie Bin” symbol on the product means that the product is classed as Electrical or
Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life.
The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 201 . AVSL Group Ltd.7

Specyfikacje produktu

Marka: LYYT
Kategoria: Kontroler
Model: ISRF1

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z LYYT ISRF1, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kontroler LYYT

LYYT

LYYT LTC22IR Instrukcja

14 Września 2024
LYYT

LYYT PS60 Instrukcja

14 Września 2024
LYYT

LYYT A2-A1818C Instrukcja

13 Września 2024
LYYT

LYYT ISRF1 Instrukcja

13 Września 2024
LYYT

LYYT AL1-W2915 Instrukcja

12 Września 2024
LYYT

LYYT IMDC1 Instrukcja

12 Września 2024
LYYT

LYYT AL2-C1709 Instrukcja

10 Września 2024
LYYT

LYYT LTC44IR Instrukcja

10 Września 2024
LYYT

LYYT AL1-C2311 Instrukcja

8 Września 2024
LYYT

LYYT PS45-24 Instrukcja

6 Września 2024

Instrukcje Kontroler

Najnowsze instrukcje dla Kontroler

PowerA

PowerA Enhanced Wireless Controller Instrukcja

26 Lutego 2025
Nyko

Nyko Sound Pad Instrukcja

25 Lutego 2025
Nyko

Nyko Air Glow 87303 Instrukcja

25 Lutego 2025
Nyko

Nyko 87270 Instrukcja

25 Lutego 2025
IPEGA

IPEGA PG-9078 Instrukcja

20 Lutego 2025
Showtec

Showtec AirDrive 2.4 Pocket Instrukcja

20 Lutego 2025
Axis

Axis TA4201 Instrukcja

20 Lutego 2025
Speed-Link

Speed-Link Black Bolt SL-650300-BK Instrukcja

20 Lutego 2025
PowerA

PowerA Advantage Wired Controller Instrukcja

19 Lutego 2025
PowerA

PowerA Enhanced Wired Controller Instrukcja

19 Lutego 2025