Instrukcja obsługi LYYT AL1-W2915

LYYT Kontroler AL1-W2915

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla LYYT AL1-W2915 (4 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 14 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/4
153.743UK User Ma al nu
RGB/RGBW Sound Active Controller
I ref: 153.743UK tem User Manual
Wireless controller for RGB/RGBW multi-colour LED tape with a 24-key handheld remote. Capable of operating 12V or
24V tape with up to 5A per channel (R/G/B) 4A (R/G/B/W). Options for 8 static colours, 3 auto sequences with speed or
control or 3 sound-activated sequences from an internal microphone or 3.5mm audio input with sensitivity control.
Operating with this controller enables RGB/RGBW tape to give sound-reactive colour to architectural features or signage.
Note: This controller can operate with 12V or 24V LED tape up to 5A maximum output per channel for R/G/B tape 5(1 A
total) and up to 4A maximum output per channel for R/G/B/W tape ( A total). For longer runs of RGB and RGBW p16 ta e
with higher current requirements, RGB/RGBW amplifiers with additional power supplies will be necessary.
If you have bought one of our LED Tape kits, you will have been supplied with a 4-pin lead to connect to connect to
RBG/RGBW tape from the controller rip the wires for R G B W + and connect to the relative screw terminals on . St / / / / V
the controller. you haven t bought one of r LED Tape kits, you will have to purchase this lead separately If ’ou .
Main Unit Specification:
Working temperature
- - 20 60℃
Supply voltage
DC5V-24V
Static power consumption
<1W
Connecting mode
common anode
Grayscale
1024 levels (RGB each)
Speed stage
100 graduations
External dimension
L72*W42*20mm
Packing size
L92*W56*H32 mm
Net weight
52g
Gross weight
81g
Output
3/4 channels
Max. Output current
3*5A(RGB)/4*4A(RGBW)
RF frequency
433.92Mhz
Remote distance
Up to 20M
PWM frequency
1.95KHz
Memory function
Yes
Short-circuit protection
Yes
Max. Output power
80W(5V); 192W(12V); 384W(24V)
RF Remote-Control Specification:
Version 1.0
Caution: Please read this manual carefully before operating
Damage caused by misuse is not covered by the warranty
Working temperature
Supply voltage
DC3V CR2025 （ ）
Standby current
Working current
12mA
Standby power
Working power
36mW
Net weight
RF frequency
433.92MHz
External dimension
RF distance
≤20m
153.743UK User Ma al nu
Main Unit Layout:
RF Remote Control Layout:
Setting up:
Connect the +V, R, G, B (and W if using RGBW tape) output to the LED tape using a connection lead, ensuring that all
terminals are fed to the correct connections on the tape. Connect 12Vdc or 24Vdc power to the DC5521 jack input or DC
power input terminals ensuring that both power supply and controller have enough current capacity to operate the ,
connected tape.
Remove the plastic tab from the handheld RF remote control unit to activate the battery (Button cell CR2025). Power up
the main control unit from the 12Vdc or 24Vdc power supply and if the LEDs are not lit, press the power ‘ON’ key on the
remote control.
Use the ‘SET’ button to set the controller according to the type of LED tape being used. The indicator light will flash
slowly for RGB tape and flash fast for RGBW tape setting.
Select static colours by pressing one of the colour keys on the remote control. Use the two brightness keys to adjust the
brightness of the LED’s. short press on the W key will switch the white LED ght on/off. A long press on the W key will A li
dim the white LED light.
153.743UK User Ma al nu
Preset auto sequences can be selected by pressing FLASH, BLOOM or SMOOTH keys. The speed of the selected preset
can be adjusted using the SPEED+/SPEED- keys.
The controller has 3 sound activated modes:
1. Press the F.T. key for a sound activated colour flash effec t
2. Press the M.T. key for a sound activated colour morph effect
3. Press the C.T. key for a sound activated colour scroll effect
Two Colo balance keys enable manual setting any of 1024 colours by stepping up or do through m incremental . r wn the ly
DIY 1 : A long press on either Y key 3 seconds will store a new light colour setting, created using the colou& 2 DI for r
balance ke . A short press will then activate the preset colour setting for that key. ys
Sound activated presets will be triggered by sound captured by the internal microphone. Alternatively, a line level audio
source may be connected to the 3.5mm audio input jack.
Sound activated triggering is adjusted using the rotary sensitivity control. To switch off the LEDs temporarily, press the
OFF key, then press ON to switch back on. If not being used for long periods, it is better to switch off the 12Vdc or 24Vdc
power supply.
Application Circuit RGB:
Application Circuit RGBW:
Warning:
• For reasons of electrical safety, this device must never be immersed in t , exposed to da conditions or wa er mp
excessive force.
• Do not use this vice if you find that it is damaged in any way. de
• Do not attempt to repair this device or take apart under any circumstances, as this will invalidate your warranty.

Specyfikacje produktu

Marka: LYYT
Kategoria: Kontroler
Model: AL1-W2915

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z LYYT AL1-W2915, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kontroler LYYT

LYYT

LYYT LTC22IR Instrukcja

14 Września 2024
LYYT

LYYT PS60 Instrukcja

14 Września 2024
LYYT

LYYT A2-A1818C Instrukcja

13 Września 2024
LYYT

LYYT ISRF1 Instrukcja

13 Września 2024
LYYT

LYYT AL1-W2915 Instrukcja

12 Września 2024
LYYT

LYYT IMDC1 Instrukcja

12 Września 2024
LYYT

LYYT AL2-C1709 Instrukcja

10 Września 2024
LYYT

LYYT LTC44IR Instrukcja

10 Września 2024
LYYT

LYYT AL1-C2311 Instrukcja

8 Września 2024
LYYT

LYYT PS45-24 Instrukcja

6 Września 2024

Instrukcje Kontroler

Najnowsze instrukcje dla Kontroler

PowerA

PowerA Enhanced Wireless Controller Instrukcja

26 Lutego 2025
Nyko

Nyko Sound Pad Instrukcja

25 Lutego 2025
Nyko

Nyko Air Glow 87303 Instrukcja

25 Lutego 2025
Nyko

Nyko 87270 Instrukcja

25 Lutego 2025
IPEGA

IPEGA PG-9078 Instrukcja

20 Lutego 2025
Showtec

Showtec AirDrive 2.4 Pocket Instrukcja

20 Lutego 2025
Axis

Axis TA4201 Instrukcja

20 Lutego 2025
Speed-Link

Speed-Link Black Bolt SL-650300-BK Instrukcja

20 Lutego 2025
PowerA

PowerA Advantage Wired Controller Instrukcja

19 Lutego 2025
PowerA

PowerA Enhanced Wired Controller Instrukcja

19 Lutego 2025