Instrukcja obsługi Lowrance EP-85R Storage Device

Lowrance Morski EP-85R Storage Device

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lowrance EP-85R Storage Device (32 stron) w kategorii Morski. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/32
1
Pub. 988-0154-522
EP-85R Storage Device
Electronic Sensor
Installation and Operation Instructions
This document shows how to connect an EP-85R storage device to a
NMEA 2000® network. The EP-85R stores Fuel Used, Trip Fuel Used
and Seasonal Fuel Used data for up to three NMEA 2000 compatible
engines that output standard NMEA 2000 Fuel Rate Data.
NMEA 2000 is the communication bus standard developed by the
National Marine Electronics Association (NMEA) for use in boats.
Lowrance has introduced a line of products that can communicate over
a NMEA 2000 network (LowranceNet).
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending.
CAUTION:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. Decide where you want to install
all components before drilling any holes in your vessel.
Some sonar or GPS display units may require a software upgrade to
display NMEA 2000 data correctly. For free software upgrades or
additional information on the LowranceNet NMEA 2000® network
system, visit our web site, www.lowrance.com.
The EP-85R Storage Device.
Smart module
Red NMEA 2000
connector
2
The EP-85R consists of a red cable connector and a smart module. It
accumulates fuel used data from fuel flow messages it receives from up
to three engines. Fuel used data includes: Fuel Range, Fuel Used, Trip
Fuel Used and Seasonal Fuel Used.
The EP-85R Storage Device, like the other LowranceNet Electronic
Probe (EP) sensors, is designed for use with a NMEA 2000 network.
Your sensor, however, is also compatible with LowranceNet blue
connector networks. It can be added to a blue connector network by
using a red female to blue female adapter cable. Your sensor MUST be
connected to a NMEA 2000 network or it WILL NOT function.
The NMEA 2000 red female to blue female adapter cable allows users
to add red connector devices to a blue connector network.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If you are connecting to an
existing LowranceNET network, those are all the electronic
components you need. If this is the first sensor you are connecting, you
will also need a one-time purchase of a LowranceNET Node Kit.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one, see the other document packed with your
EP-85R Storage Device, "Setup and Installation of NMEA 2000
Networks, General Information," part number 988-0154-173. If that
document is not available, it can be downloaded free at
www.lowrance.com.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2-foot
extension cable, T connector and two 120-ohm terminators.
3
Installation
To install the EP-85R Storage Device, route the sensor's cable
connector to the T on the network backbone where you intend to attach
it and plug it in.
Connecting to a NMEA 2000 Network
A NMEA 2000 network is a communications link between two or more
devices that transfer NMEA 2000 information. LowranceNET is the
NMEA 2000 networking system developed by Lowrance Electronics. A
NMEA 2000 network functions like the phone wiring in a house. If, for
example, you pick up a phone in the living room you will be able to
hear the conversation someone is having on a phone in the bedroom.
In similar fashion, a NMEA 2000 network allows multiple display units
to receive data from a GPS antenna or multiple sonar units to receive
messages sent by a temperature sensor. A NMEA 2000 network gives
you the flexibility to view information like engine diagnostics and fuel
level data on digital gauges or display units located anywhere on your
boat.
There are two types of LowranceNet red connectors: the single T
connector (left) and the double T connector (right).
Network Backbone and Network Nodes
A network bus backbone consists of network cabling, terminators and T
connectors. Network nodes are made by fitting T-shaped connectors into
the backbone (using the sockets on the sides) and attaching any network
device to the bottom of the T.
Staying with the previous phone wiring example, T connectors on the
backbone are the equivalent of phone jacks spread throughout a house.
To pick up a phone and be able to hear a conversation from another
phone in the house, both phones have to be connected to the main phone
line. In similar fashion, only sensors and display units plugged into the
NMEA network can share information. The network backbone is like the
phone wiring that runs throughout a home.


Specyfikacje produktu

Marka: Lowrance
Kategoria: Morski
Model: EP-85R Storage Device

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Lowrance EP-85R Storage Device, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Morski Lowrance

Instrukcje Morski

Najnowsze instrukcje dla Morski

Silva

Silva S15 Instrukcja

28 Września 2024
Silva

Silva S15-N Navtex Instrukcja

28 Września 2024
IVT

IVT 8A Solar Instrukcja

28 Września 2024
Digital Yacht

Digital Yacht WL400 Instrukcja

28 Września 2024
Digital Yacht

Digital Yacht WL50 Instrukcja

28 Września 2024
Digital Yacht

Digital Yacht WL500 Instrukcja

28 Września 2024
Humminbird

Humminbird 323 Instrukcja

27 Września 2024