Instrukcja obsługi Lowrance EP-25 Speed
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lowrance EP-25 Speed (8 stron) w kategorii Morski. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/8
1
Pub. 988-0154-451
EP-25 Speed
Electronic Sensor
Installation Instructions
This instruction sheet tells how to install your EP-25 Speed sensor and
connect it to a NMEA 2000 network using LowranceNET network
components. You must refer to your digital gauge, sonar or GPS unit's
manual for sensor operation instructions.
Caution:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. You should decide where to
install all components before drilling any holes in your vessel.
Some sonar or GPS units may require a software upgrade to display
NMEA 2000 data correctly and a manual addendum describing how to
operate the sensor. You can download these free and get additional
information on the NMEA 2000 compatible LowranceNET system at
our web site, www.lowrance.com.
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending. See our web site for the latest
product status information.
The EP-25 Speed sensor.
The EP-25 consists of the paddle wheel module, a blue female locking
cable connector and the smart module. The cable length from the
Paddle wheel module
Smart module
Blue female NMEA
2000 connector
2
connector to the smart module is 18 inches (46 cm) and from the smart
module to the paddle wheel module is 10 feet (3 meters).
The smart module converts speed data from the paddle wheel to the
NMEA 2000 data format. This allows any digital gauge, sonar or GPS
unit connected to the NMEA 2000 network to display the speed.
The EP-25 Speed, like the other Lowrance Electronic Probe (EP)
sensors, is designed only for use with a NMEA 2000 Network. It must
be connected to a NMEA 2000 network or it will not function.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
LowranceNET NMEA 2000 network. If you are connecting to an
existing LowranceNET network, those are all the electronic
components you need. If this is the first sensor you are connecting, you
will also need a one-time purchase of a LowranceNET Node Kit.
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2 foot (61
cm) extension cable, T connector, 120-ohm male terminator and 120-
ohm female terminator.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one refer to the "Setup and Installation of NEMA
2000 Networks, General Information" document (part number 988-
0154-172) included with your EP-25 sensor. If that document is missing
it can be downloaded free from the Lowrance web site.
Supplies are not included, unless otherwise indicated. Required supplies
for this job are: four #8 stainless steel wood screws (3/4" or 19 mm long),
high quality, marine grade above- or below-waterline sealant compound.
Recommended tools for this job include: screwdriver, drill, 1/8" (3 mm) drill
bit for pilot holes. If you want to feed the smart module or blue cable
connector through a transom or bulkhead, you will also need a 7/8" (22
mm) drill bit.
3
Installation
To install the speed sensor, first find a location on the boat's transom
where the water flow is smoothest. Don't mount the paddle wheel
module behind strakes or ribs. These will disturb the water flow to the
paddle wheel.
Make sure the paddle wheel will remain in the water when the boat is
on plane. Also make sure the location doesn't interfere with the boat's
trailer. Typically, the paddle wheel module is mounted about one foot
(30.5 cm) to the side of the transom's centerline.
Stern view showing good mounting location on transom.
Once you've determined the proper location for the paddle wheel, place
it on the transom. The bottom of the bracket should be flush with the
hull's bottom. Using the paddle wheel's bracket as a template, mark the
hull for the screws' pilot holes. Drill four 1/8" (3 mm) holes, one in each
end of the slots.
Paddle wheel module rear view.
Mount the paddle wheel module to the hull using four #8 stainless steel
wood screws. Use a high quality, marine grade above- or below-
waterline sealant to seal the screws. Make sure the paddle wheel
bracket is flush with the bottom of the hull and tighten the screws.
good location
Rear view
Bottom of hull
Specyfikacje produktu
| Marka: | Lowrance |
| Kategoria: | Morski |
| Model: | EP-25 Speed |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Lowrance EP-25 Speed, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Morski Lowrance
25 Września 2024
25 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
17 Września 2024
17 Września 2024
12 Września 2024
Instrukcje Morski
- Morski President
- Morski Garmin
- Morski Fusion
- Morski IVT
- Morski ICOM
- Morski Simrad
- Morski Raymarine
- Morski Rockford Fosgate
- Morski Humminbird
- Morski Alphatron
- Morski Silva
- Morski Polmar
- Morski Eagle
- Morski Furuno
- Morski Klarfit
- Morski BandG
- Morski Dickinson Marine
- Morski Efoy
- Morski Navionics
- Morski Echotec
- Morski Interphase
- Morski Lofrans
- Morski Fastnet
- Morski KVH
- Morski Standard Horizon
- Morski SEAFARER
- Morski Nasa
- Morski Katadyn
- Morski Sailtron
- Morski Lorenz
- Morski Raytheon
- Morski Geonav
- Morski Digital Yacht
- Morski Plastimo
Najnowsze instrukcje dla Morski
5 Października 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
27 Września 2024