Instrukcja obsługi Lowrance EP-80R Temp
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Lowrance EP-80R Temp (28 stron) w kategorii Morski. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/28
1
Pub. 988-0154-472
EP-80R Temp
Electronic Temperature Sensor
Installation and Configuration Instructions
This document shows how to install an EP-80R temp sensor and how to
connect it to a NMEA 2000® network. It also provides instructions on
how to configure your temp sensor with Lowrance digital gauges (LMF-
200 & LMF-400) and display units.
NMEA 2000 is the communication bus standard developed by the
National Marine Electronics Association (NMEA) for use in boats.
Lowrance has introduced a line of products that can communicate over
a NMEA 2000 network (LowranceNet).
All Lowrance NMEA 2000 capable devices are either NMEA 2000
certified or certification is pending.
CAUTION:
Installing LowranceNET NMEA 2000 devices is significantly
different from installing earlier Lowrance components without
NMEA 2000 features. You should read all of the installation
instructions before proceeding. Decide where you want to install
all components before drilling any holes in your vessel.
Some sonar or GPS display units may require a software upgrade to
display NMEA 2000 data correctly. For free software upgrades or
additional information on the LowranceNet NMEA 2000® network
system, visit our web site, www.lowrance.com.
The EP-80R temperature sensor.
Temp
module
Smart module
NMEA 2000 red
cable connector
2
The EP-80R consists of the temp sensor module, a red cable connector
and the smart module, which converts analog temperature data to
NMEA 2000 data format. The cable length measures 18 inches (46 cm)
from the connector to the smart module and 10 feet (3 meters) from the
smart module to the temp module. The EP-80R Temp, like the other
LowranceNet Electronic Probe (EP) sensors, is designed for use with a
NMEA 2000 network. Your sensor, however, is also compatible with
LowranceNet blue connector networks. It can be added to a blue
connector network by using a red female to blue female adapter cable.
One way or another, your sensor MUST be connected to a NMEA 2000
network or it WILL NOT function.
The NMEA 2000 red female to blue female adapter cable allows users
to add red connector devices to a blue connector network.
Tools and Supplies
Your EP sensor packs with a T connector needed to attach it to a
NMEA 2000 LowranceNet network. If you are connecting to an existing
LowranceNET network, those are all the electronic components you
need. If this is the first sensor you are connecting, you will need to
purchase a LowranceNET Node Kit.
For complete instructions on setting up a new NMEA 2000 network or
expanding an existing one, see the NMEA 2000 document packed with
your EP-80R Temp, "Setup and Installation of NMEA 2000 Networks,
General Information," part number 988-0154-173. If that document is
missing, it can be downloaded free from the Lowrance web site.
Other supplies are not included, unless otherwise indicated. A transom
mount requires one #8 stainless steel screw (3/4" long) and a high
quality, marine-grade above- or below-waterline sealant/adhesive
compound. If you need a pilot hole for the screw, use a drill and a 1/8"
drill bit. If you want to feed the temp module through a transom or
bulkhead, use a 3/4" bit. A screwdriver is needed for mounting the temp
sensor.
3
LowranceNET Node Kit for a NMEA 2000 network. Includes a 2-foot
extension cable, T connector and two 120-ohm terminators.
Installation
The EP-80R temperature sensor can be mounted in any location where
you want temperature to be monitored. The most common applications
are transom mounts — to measure surface water temperature — or in
a livewell. Wherever you install it, make sure the temp module will be
in contact with the water at all times. If the sensor is mounted on the
transom, make sure it is mounted in a manner that prevents it from
coming into contact with the boat trailer.
Caution:
If you drill a hole in the transom for the cable, make sure it is
located above the waterline. After installation, be sure to seal the
cable hole with the same marine grade above-or below-waterline
sealant used for the screw.
Temp module on transom with cable routed through the transom.
Notice that the sensor was routed so the smart module is inboard.
After determining the location, use the temp module as a template and
mark the hull for the screw's pilot hole. Route the temp module and
cable over or through the transom to the mounting location. If routing
through the transom, drill a 3/4" hole to accommodate the temp
module. Make sure the smart module is inboard and not left exposed on
Specyfikacje produktu
| Marka: | Lowrance |
| Kategoria: | Morski |
| Model: | EP-80R Temp |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Lowrance EP-80R Temp, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Morski Lowrance
25 Września 2024
25 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
23 Września 2024
17 Września 2024
17 Września 2024
12 Września 2024
Instrukcje Morski
- Morski President
- Morski Garmin
- Morski Fusion
- Morski IVT
- Morski ICOM
- Morski Simrad
- Morski Raymarine
- Morski Rockford Fosgate
- Morski Humminbird
- Morski Alphatron
- Morski Silva
- Morski Polmar
- Morski Eagle
- Morski Furuno
- Morski Klarfit
- Morski BandG
- Morski Dickinson Marine
- Morski Efoy
- Morski Navionics
- Morski Echotec
- Morski Interphase
- Morski Easy
- Morski Lofrans
- Morski Fastnet
- Morski KVH
- Morski Standard Horizon
- Morski SEAFARER
- Morski Nasa
- Morski Katadyn
- Morski Sailtron
- Morski Lorenz
- Morski Raytheon
- Morski Geonav
- Morski Digital Yacht
- Morski Plastimo
Najnowsze instrukcje dla Morski
5 Października 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
27 Września 2024