Instrukcja obsługi Ionmax ION10
Ionmax
filtr do wody
ION10
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Ionmax ION10 (2 stron) w kategorii filtr do wody. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
'9)+8/5+/'2+8+6/7
246+8.'32246
786'/-.85'68/7
1+77 8.'3 22
+)8'3-91'646
:'1"=5+
$/8.!+3746"=5+
!.4;+64>>1+"=5+
466493*'9)+87
222222
46462/3-'9)+87
33+6"=5+
46462/3-
'9)+87
!+88/3-"441
8.+6'9)+8"=5+7
!86'/-.8'9)+8"=5+7
58/43'1/88/3-*'5846
/6.4
PRODUCT DIAGRAM
HOW TO USE
SPECIFICATION
WATER PRESSURE
FITTING ADAPTER
REPLACING THE AIR FILTER
Faucet Pipe Diameter is
more than 25mm or straight
part is less than 15 mm
Turn the lever to switch between normal tap water and ozone water faucets.
CAUTION: Do not turn the lever in any other direction other than illustrated as this will break the lever.
The ION10 converts tap water into ozone water. The unit relies on water pressure to work properly.
The ‘Operating’ Green LED will light up when the water pressure is sufcient and ozone is being
produced. If The ‘Operating’ Green LED does not light up, it means that there is insufcient water
pressure to generate ozone. When the water pressure is higher than 0.35Mpa, the ‘Overload’ Red LED
will light up and the unit may emit noise and stop ozone production. In this case, turn off the faucet and
turn it back on slowly until the ‘Operating’ Green LED lights up.
The air lter is installed to dehumidify the inside of the unit. It can last for
more than twelve (12) months under normal usage. If the unit is being used
in high humidity conditions for an extended period, it would need to be
replaced sooner.
The air lter can be removed by turning it counterclockwise.
When the lever is up, the water will ow straight through the
unit and provide normal tap water.
The ‘Operating’ Green LED will not light up.
When the lever is down, the water will ow into the unit
andout of the ozone water faucet to provide ozone water.
The ‘Operating’ Green LED will light up.
Optional Fitting Adaptor
Universal Coupling
‘Operating’ Green LED
Air Filter
Attachment
Ozone/Tap Water
Change Lever
Tap Water Faucet
Ozone Water Faucet
Vent with lter
‘Overload’ Red LED
NOTE: The tting adaptor cannot be used for the following faucet types:
Ozone Production: 70mg/h
Electric Generator: AC Generator
Output Power: Max 3.0 Watt
Water Pressure Range: 0.15 - 0.40 Mpa
Applicable Faucet: See below
Weight: 310g
Dimensions: W100 x L126 x H73
Main Material: ABS
ION10 OZONE WATER GENERATOR
Instruction Manual
CLEANING THE WIRE MESH FILTER
Wire
mesh
lter
For the unit to function, the tap water ow needs to have sufcient water
pressure. When dirt or foreign substances get stuck to the wire mesh lter,
it may lower the water pressure and reduce the unit’s ability to produce
ozone.
Clean the wire mesh lter regularly and be sure to reassemble it correctly
to prevent water leakage in the tting adaptor.
For the unit to function, the tap water ow needs to have sufcient water
pressure. When dirt or foreign substances get stuck to the wire mesh lter,
it may lower the water pressure and reduce the unit’s ability to produce
ozone.
Clean the wire mesh lter regularly and be sure to reassemble it correctly
to prevent water leakage in the tting adaptor.
FITTING ADAPTOR INSTALLATION GUIDE FOR FORMING FAUCET OPTIONAL FITTIMG ADAPTOR INSTALLATION GUIDE
CAUTION
Remove the forming cap from the faucet.
Select the correct tting
adaptor
Put the coupling and adaptor
onto the faucet pipe.
Put the coupling and adaptor onto the faucet pipe.
Loosen the coupling and insert faucet to optional adaptor with
the unit horizontally.
Tighten four screw uniformly then tighten the coupling.
Check for water leakages after installation.
If the water leaks from the joint part, to make sure whether the
coupling and four screws are tightened enough or check the
unit is set horizontally.
• Please wait at least 5 minutes before drinking ozone water.
• Ensure adequate ventilation around the unit when operating.
• Ensure the air lter remains clean and dry.
• Do not block the water faucet with hands or other objects.
• As this product contains electric components, do not immerse or submerge it in water. To clean
the unit, wipe using a damp cloth.
• In high humidity environments such as bathrooms, the ozone generating capacity will be less
efcient.
Follow the steps in Fig.1 above
for installation and check for
water leakages.
Select the correct tting adaptor and connect
the coupling to the faucet head.
Use the setting tool to tighten the tting
adaptor.
Hold the unit rmly from the bottom to align
the faucet to the inlet properly, and then
tighten the coupling.
Check for water leakages after installation.
If the water leaks from the joint part, make
sure that the coupling is tightened or try
another adaptor until the unit is securely
tted with no leakages.
INNER TYPE OUTER TYPE
FITTING ADAPTOR INSTALLATION GUIDE FOR ROUND FAUCET
Fig. 1
Specyfikacje produktu
| Marka: | Ionmax |
| Kategoria: | filtr do wody |
| Model: | ION10 |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Ionmax ION10, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje filtr do wody Ionmax
24 Września 2024
Instrukcje filtr do wody
- filtr do wody Electrolux
- filtr do wody Philips
- filtr do wody GE
- filtr do wody BRITA
- filtr do wody Hyundai
- filtr do wody Fisher & Paykel
- filtr do wody Fiap
- filtr do wody Grohe
- filtr do wody Juwel
- filtr do wody Ecowater
- filtr do wody Franke
- filtr do wody Eheim
- filtr do wody Flama
- filtr do wody PUR
Najnowsze instrukcje dla filtr do wody
2 Października 2024
29 Września 2024
22 Sierpnia 2024
7 Sierpnia 2024
18 Czerwca 2024
27 Maja 2024
26 Maja 2024
25 Maja 2024
23 Maja 2024
16 Maja 2024