Instrukcja obsługi Honeywell LYNX Touch L5210

Honeywell system alarmowy LYNX Touch L5210

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell LYNX Touch L5210 (88 stron) w kategorii system alarmowy. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/88

800-19974 12/14 Rev. A

LYNX Touch Installation and Setup Guide

- 2 -

RECOMMENDATIONS FOR PROPER PROTECTION

The Following Recommendations for the Location of Fire and Burglary Detection Devices Help

Provide Proper Coverage for the Protected Premises.

Recommendations for Smoke and Heat Detectors

With regard to the number and placement of smoke/heat detectors, we subscribe to the

recommendations contained in the National Fire Protection Association's (NFPA) Standard #72

noted below.

• Early warning fire detection is best achieved by the installation of fire detection equipment in all rooms and

areas of the household as follows: For minimum protection a smoke detector should be installed outside of

each separate sleeping area, and on each additional floor of a multi-floor family living unit, including

basements. The installation of smoke detectors in kitchens, attics (finished or unfinished), or in garages is not

normally recommended.

• For additional protection the NFPA recommends that you install heat or smoke detectors in the living room,

dining room, bedroom(s), kitchen, hallway(s), attic, furnace room, utility and storage rooms, basements and

attached garages.

In addition, we recommend the following:

• Install a smoke detector inside every bedroom where a smoker sleeps.

• Install a smoke detector inside every bedroom where someone sleeps with the door partly or completely

closed. Smoke could be blocked by the closed door. Also, an alarm in the hallway outside may not wake up the

sleeper if the door is closed.

• Install a smoke detector inside bedrooms where electrical appliances (such as portable heaters, air

conditioners or humidifiers) are used.

• Install a smoke detector at both ends of a hallway if the hallway is more than 40 feet (12 meters) long.

• Install smoke detectors in any room where an alarm control is located, or in any room where alarm control

connections to an AC source or phone lines are made. If detectors are not so located, a fire within the room

could prevent the control from reporting a fire or an intrusion.

THIS CONTROL COMPLIES WITH NFPA REQUIREMENTS FOR TEMPORAL PULSE

SOUNDING OF FIRE NOTIFICATION APPLIANCES.

DINING

KITCHEN BEDROOM

BEDROOM

LIVING ROOM BEDROOM

BDRM

DINING

LIVING ROOM

TV ROOM KITCHEN

BEDROOM BEDROOM

LVNG RM

BASEMENT

KTCHN

CLOSED

DOOR

GARAGE

Smoke Detectors for Minimum Protection

Smoke Detectors for Additional Protection

Heat-Activated Detectors

BDRM

floor_plan-001-V1

Recommendations For Proper Intrusion Protection

• For proper intrusion coverage, sensors should be located at every possible point of entry to a home or

premises. This would include any skylights that may be present, and the upper windows in a multi-level

building.

• In addition, we recommend that radio backup be used in a security system. This will ensure that alarm

signals can be sent to the alarm monitoring station in the event that the telephone lines are out of order

(alarm signals are normally sent over the phone lines, if connected to an alarm monitoring station).

LYNX Touch Installation and Setup Guide

-3-

Table of Contents

System Features ................................................................................................................................................................................. 5

Installing the Control ........................................................................................................................................................................ 7

Wall Mounting ............................................................................................................................................................................... 7

Desktop Mounting .......................................................................................................................................................................... 7

Wiring Overview ............................................................................................................................................................................ 8

Wiring Connections ........................................................................................................................................................................... 9

AC Power and Backup Battery ....................................................................................................................................................... 9

General ................................................................................................................................................................................................ 10

Installing the Rechargeable Backup Battery .............................................................................................................................. 10

Replacing the Rechargeable Backup Battery.............................................................................................................................. 10

Battery Selection .......................................................................................................................................................................... 10

Installing/Configuring Communications & Home Automation Modules ............................................................................. 12

Connecting and Configuring Communications Modules .................................................................................................................... 12

Installing the 4GL/4GLC or 3GL/3GLC ...................................................................................................................................... 12

Installing the ILP5 ....................................................................................................................................................................... 14

Installing the L5100-WiFi Module .............................................................................................................................................. 15

Installing the L5100-ZWAVE Module ......................................................................................................................................... 15

Installing Wireless Zones ............................................................................................................................................................... 17

General Information ............................................................................................................................................................................ 17

Zones............................................................................................................................................................................................. 17

Range ............................................................................................................................................................................................ 17

Transmitters ................................................................................................................................................................................ 17

House Identification ..................................................................................................................................................................... 17

Transmitter Supervision ............................................................................................................................................................. 17

Transmitter Input Types ............................................................................................................................................................. 17

Transmitter Battery Life ............................................................................................................................................................. 17

RF Sniffer Test Mode ................................................................................................................................................................... 18

Go-No-Go Test Mode .................................................................................................................................................................... 18

5800 Series Transmitter Loop Numbers ..................................................................................................................................... 19

Mechanics of Programming ........................................................................................................................................................... 20

Navigating Menus ............................................................................................................................................................................... 20

Touchscreen Display .................................................................................................................................................................... 20

Navigation Keys ........................................................................................................................................................................... 21

Home Screen ................................................................................................................................................................................ 21

Security Screen ............................................................................................................................................................................ 22

Security Menus ............................................................................................................................................................................ 22

Installer Tools Menu .................................................................................................................................................................... 22

User Tools Menu .......................................................................................................................................................................... 22

General Programming Information .................................................................................................................................................... 23

Programming ....................................................................................................................................................................................... 23

Enter Installer Programming Mode ............................................................................................................................................ 23

Loading Factory Defaults .................................................................................................................................................................... 24

Select a Default Configuration .................................................................................................................................................... 24

Exiting Programming Mode ................................................................................................................................................................ 24

Zone Response Type Definitions .................................................................................................................................................. 25

General Information ............................................................................................................................................................................ 25

Programming the Control .............................................................................................................................................................. 27

Enter Installer Programming Mode without using Installer Code ................................................................................................... 27

Change Installer Code ......................................................................................................................................................................... 27

Select a Language................................................................................................................................................................................ 27

System Type ........................................................................................................................................................................................ 27

Program Date and Time ...................................................................................................................................................................... 30

Program the Communications Module ............................................................................................................................................... 31

Program the Z-Wave Module .............................................................................................................................................................. 34

Program Zones ..................................................................................................................................................................................... 35

Program Keys ...................................................................................................................................................................................... 38

Program Reporting .............................................................................................................................................................................. 40

Program Sounder................................................................................................................................................................................. 47

Program System Settings .................................................................................................................................................................... 48

Communications Diagnostics .............................................................................................................................................................. 51

Communications Status ............................................................................................................................................................... 51

Ethernet Information ................................................................................................................................................................... 51

GSM Information ......................................................................................................................................................................... 51