Instrukcja obsługi Honeywell HBW4PER2

Honeywell kamera bezpieczeństwa HBW4PER2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell HBW4PER2 (2 stron) w kategorii kamera bezpieczeństwa. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

HBW8PR2 WDR 8MP IR Bullet Camera

Quick Installation Guide

Thank you for purchasing a Honeywell Performance Series IP

camera. Follow the instructions in this guide to install and log

in to your camera. For instructions on conﬁguring the camera,

refer to the user guide on the CD that came with your camera.

If you require additional assistance, call the number listed for

your region on the back cover.

Cautions and Warnings

WARNING

To ensure compliance with electrical safety standards, this product is

intended for use with a Listed Power Adapter marked “Limited Power

Source” or “LPS” on the unit, output rated to 12 VDC, minimum 0.33 A,

TMA=60 deg C, or from Power over Ethernet (PoE) provided by Listed

Information Technology Equipment meeting IEEE 802.3af PoE standard.

CAUTION

The Ethernet connection is not intended to be connected to exposed

(outside plant) networks. Do not connect two power sources to the camera

at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam.

Important Safeguards

• Read and keep these instructions.

• Confirm the installation surface can support at least three times the weight of the

camera.

• Do not aim the camera toward a bright light source for extended periods to prevent

damage to the imager.

• Avoid operating the unit under or close to unstable light sources (may cause flickering),

or close to fluorescent lamps or objects reflecting light.

• Do not touch the camera lens.

• Do not drop the camera or subject it to physical shock.

• Do not use a strong or abrasive detergent when cleaning the camera.

• Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments,

where the operating temperature is outside the -recommended range of 22°F to 140°F

(–3 0°C to 60°C).

• Do not apply power to the camera before completing installation.

Before You Begin

Before you begin, check that you have received all of the parts listed below. If any parts are

missing or damaged, contact your dealer immediately.

•

Camera

• Installation CD

• Quick installation guide

• Allen key (L- wrench)

•

Self-tapping screws (×4)

• Plastic wall anchors (×4)

• Mounting template

CAUTION Installation and servicing should be performed only by qualified and experienced

technicians to conform to all local codes and to maintain your warranty.

Preparing the Mounting Surface

1. Apply the mounting template to the mounting

surface.

Note Observe the orientation of the cable exit notch

on the bracket base. In outdoor installations, the

notch should point downward to prevent water from

entering the camera housing.

2. Using the mounting template as a guide, drill three

pilot holes in the mounting surface, then hammer the

supplied anchors into the holes.

3. Drill a cable entry hole in the mounting surface, then pull the required cables through the

hole.

Mounting and Aiming the

Camera

1. If you are using a microSD card with

the camera, install it before continuing.

Remove the panel on the underside of

CAUTION

THIS SYMBOL INDICATES THAT

DANGEROUS VOLTAGE

CONSTITUTING A RISK OF

ELECTRIC SHOCK IS PRESENT

WITHIN THE UNIT.

CA : TUTION O REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE OVER.THE C

NO USER-SERVICEABLE PAR .TS INSIDE

REFER SER TO QUVICING ALIFIED SERVICE

PERSONNEL.

THIS SYMBOL INDICATES THAT

IMPORTANT OPERATING AND

MAINTENANCE INSTRUCTIONS

ACCOMPANY THIS UNIT.

RISK OF ELECTRIC

SHOCK

DO NOT OPEN

Figure 1

© 2018 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However, Honeywell

cannot assume responsibility for any consequences resulting from the use thereof. The information contained herein is subject to change without notice. Revisions or new additions to this publication may be issued to incorporate such changes.

the camera and insert a microSD card into the ). SD card slot (refer to Figure 1

2. Connect one end of the Ethernet cable to the RJ-45 port on the camera.

3. If the other end of the Ethernet cable is NOT connected to a PoE switch or NVR, connect

the power connector of the camera to a 12 VDC power source.

4. Attach the camera assembly to the mounting

surface using the supplied screws.

5. Using the supplied Allen key, loosen the

locking screws on the mounting bracket arm,

point the camera in the desired direction by

rotating the camera body and mounting

bracket arm, then tighten the screws (refer to

Figure 2).

Logging On to the Camera

If the camera is connected to the PoE port of a Honeywell Embedded NVR, it can be

configured using the NVR.

To log on remotely from a PC, install the Honeywell Config Tool from the software and

documentation CD, find the camera on the network, and then open the web browser with the

Honeywell Config Tool. The default user name is admin -(case sensitive) and the default

password is 1234.

Note



Only Internet Explorer 11 (or later) is supported.



IP address of the device is assigned automatically by server. If the DHCP server is not DHCP

available, the device will acquire 192.168.1.108 as the default IP address.

Adjusting the Zoom and Focus Settings

After you have logged on to the camera, go to Setup  Camera   Conditions Zoom and

Focus to fine- tune the camera’s zoom and focus settings.

Recommended Recorders

HEN*4 8/16/32/64 264 and H.265)-channel Focus 4K NVRs (H.

HEN*3 4/8/16/32-channel Performance Series NVRs (H.264 ) and H.265

Regulatory Statements

FCC Compliance

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

Note Changes or modifications not expressly approved by the party responsible for

compliance could void the user’s authority to operate the equipment.

This Class B digital apparatus complies with Canadian ICES- 003.

Manufacturer’s Declaration of Conformance

North America The equipment supplied with this guide conforms to UL 60950-1 and CSA

C22.2 No. 60950-1.

Europe The manufacturer declares that the equipment supplied is compliant with the

European Parliament and Council Directive on the restriction of the use of certain hazardous

substances in electrical and electronic equipment (2011/65/EU), General Product Safety

Directive (2001/95/EC), and the essential requirements of the EMC directive (2014/30/EU),

conforming to the requirements of standards EN 55032 for emissions, EN 50130-4 for

immunity, and EN 62368 1 for electrical equipment- safety.

WEEE (Waste Electrical and Electronic Equipment)

Correct disposal of this product (applicable in the European Union and other

European countries with separate collection systems). This product should be

disposed of, at the end of its useful life, as per applicable local laws, regulations,

and procedures.

Honeywell

2700 Blankenbaker Pkwy, Suite 150

Louisville, KY, 40299, USA

www.honeywell.com/security

+1 800 323 4576

(North America only)

Aston Fields Road, Whitehouse Industrial

Estate Runcorn, Cheshire, WA7 3DL, UK

www.honeywell.com/security/uk

+1 44 (0) 1928 754 028

(Europe only)

Building #1, 555 Huanke Road, Zhang Jiang Hi-Tech

Park, Pudong New Area, Shanghai, 201203, China

www.asia.security.honeywell.com

+400 840 2233

(Asia Pacific only)

Document 800-245 /20196 – – 08Rev A 8

Figure 2

Specyfikacje produktu

Marka:	Honeywell
Kategoria:	kamera bezpieczeństwa
Model:	HBW4PER2
Kolor produktu:	Black, White
Rodzaj zasilania:	DC, PoE
Wysokość produktu:	90.4 mm
Szerokość produktu:	214.8 mm
Waga produktu:	685 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Technologia łączności:	Przewodowa
Bluetooth:	Nie
Certyfikaty:	FCC Part 15B, EN 55032\nEN 50130-4\nEU: EN 60950-1\nNorth America UL listed to UL/CSA 60950-1\nEN 50581
Maksymalne zużycie mocy:	11.74 W
Liczba kamer:	1
Formaty kompresji:	H.264, H.264+, H.265, H.265+
Obsługiwane systemy operacyjne Windows:	Windows 7, Windows 7 Enterprise, Windows 7 Home Basic, Windows 7 Home Premium, Windows 7 Professional, Windows 7 Starter, Windows 7 Ultimate
Obsługiwane typy kart pamięci:	MicroSDHC
Maksymalny rozmiar karty pamięci:	128 GB
Przeznaczenie:	Wewnętrz i na wolnym powietrzu
Standardy komunikacyjne:	IEEE 802.3af
Ilość portów Ethernet LAN (RJ-45):	1
Zakres temperatur (eksploatacja):	-30 - 60 °C
Zakres wilgotności względnej:	0 - 95 %
Układ:	Pocisk
Tryb nocny:	Tak
Wi-Fi:	Nie
Przewodowa sieć LAN:	Tak
Zintegrowany czytnik kart:	Tak
Waga wraz z opakowaniem:	860 g
Zakres temperatur (przechowywanie):	-30 - 60 °C
Dopuszczalna wilgotność względna:	0 - 95 %
Model:	Kamera bezpieczeństwa IP
Technologia okablowania:	10/100Base-T(X)
Maks. rozdzielczość:	2688 x 1520 px
Rodzaj interfejsu sieci Ethernet:	Fast Ethernet
Stopień ochrony IP:	IP66
Typ mocowania:	Ściana
Stosunek sygnału do szumu:	45 dB
Obsługiwane protokoły sieciowe:	IPv4/v6, TCP/IP, UDP, RTP, RTSP, RTCP, HTTP, HTTPS, SSL, FTP, SMTP, DHCP, PPPoE, UPnP, SNMP v2/v3, Bonjour, DNS, DDNS, IEEE 802.1X, QoS, NTP
Długość ogniskowa:	2.7 - 13.5 mm
Cyfrowe zbliżenie:	16 x
Obsługiwane rozdzielczości grafiki:	352 x 240,352 x 288,640 x 480 (VGA),704 x 480,704 x 576,1280 x 1024 (SXGA),1280 x 720 (HD 720),1280 x 960,1920 x 1080 (HD 1080),2304 x 1296,2560 x 1440,2688 x 1520
Typ przetwornika obrazu:	CMOS
Suma megapikseli:	4 MP
Balans bieli:	Auto, Manual, Natural, Outdoor
Typ migawki aparatu:	Elektroniczny
Tryb dzienny / nocny:	Tak
Typ diody LED:	Podczerwień
Min. Oświetlenie:	0.03 lx
System formatu sygnału analogowego:	NTSC, PAL
Wbudowany HDD:	Nie
Kąt widzenia obiektywu, w poziomie:	104 °
Kąt widzenia obiektywu w pionie:	55 °
Wielkość czujnika CCD:	1/3 "
Skanowanie progresywne:	Tak
Video detektor ruchu:	Tak
Ilość klatek:	30 fps
Szybkość migawki:	1/3 - 1/100000 s
Liczba użytkowników:	20 użyt.
Liczba czujników:	1
Kompensacja oświetlenia tylnego:	Tak
Odległość widzenia nocnego (Night Vision):	50 m
Liczba soczewek:	1
Maska prywatności:	Tak
Minimalna przesłona:	1.4