Instrukcja obsługi Honeywell H4D3PRV2

Honeywell kamera bezpieczeństwa H4D3PRV2

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Honeywell H4D3PRV2 (2 stron) w kategorii kamera bezpieczeństwa. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

H4D3PRV2 True Day/Night Rugged Indoor/Outdoor

IR Minidome IP Camera Regulatory Statements

Information to the User: This has equipment been and tested found to comply with the limits afor

Class B digital device, pursuant to part 15 of the Rules. FCC These limits are designed to provide

reasonable against protection harmful interference a in residential installation. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance

with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that a particular interference will not occur in installation.

Quick Installation Guide

Document - 1800 2123 V1— A– Rev 10/2015

Thank you for a 2 camera. purchasing H4D3PRV

Follow the

instructions in this guide and to install

log on to

your camera. For instructions on

configuring the

camera, refer to the Performance

Series IP

Cameras User Guide on the software

and

documentation CD that came with your

camera. If

you require additional assistance,

please call the

number shown below.

If this equipment does cause harmful interference to radio be or television reception, which can

determined by turning the equipment is and off on, the user encouraged to try to correct the

interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

Increase the the separation between equipment and receiver.

Connect the equipment into an outlet a that on circuit different from to which the receiver is

connected.

Consult the dealer or an experienced radio/TV technician for help.

Cautions and Warnings

•

Note Changes or modifications not expressly approved by party the responsible for compliance

could void the user’s authority to operate the equipment.

This B Class digital apparatus complies Canadian with ICES- 003.

Cet appareil numérique de la B à Classe est conforme la - Canada. norme NMB 003 du

Important Safeguards

WARNING

•

Read and keep these instructions.

Do not aim the camera toward a bright light source for extended periods to prevent damage to

the imager. Avoid operating the unit under or close to unstable light sources (may cause

flickering), or close to fluorescent lamps or objects reflecting light.

Do not touch the camera lens.

Do not drop the camera or subject it to physical shock.

Do not use a strong or abrasive detergent when cleaning the camera.

Avoid operating or storing the unit in extremely humid, dusty, hot/cold environments, where the

operating temperature is outside the recommended range of – 4°F to 140°F (– 20°C to 60°C).

To ensure compliance with electrical safety standards this product is

intended for use with a Listed Power Adapter marked with “Limited Power Source”, “LPS”,

on the unit, output rated 12 V DC, minimum 0.33A, Tma=60Deg.C or from Power over

Ethernet (PoE) provided by Listed Information Technology Equipment meeting the IEEE

802.3af PoE standard. •

•

The Ethernet connection is not intended to be connected to exposed (outside plant)

networks. Do not connect two power sources to the camera at the same time.

CAUTION

Invisible LED radiation (850 nm). Avoid exposure to beam. Note

Do not apply power to the completing installation. camera before

Note

Confirm the installation surface can support at least three times the weight of the camera.

Document - 1 – A– 800 2123 V1 Rev 10/2015

H4D3PRV2 True Day/Night Rugged Indoor/Outdoor IR Minidome IP Camera

Before You Begin

Before you begin, that check you have received all of the parts listed If any parts are below. missing

or your damaged, contact dealer immediately.

•

Camera

Documentation CD

Quick install guide

Allen key (L- wrench)

•

Self- 3)tapping screws (×

Plastic wall anchors 3)(×

Mounting template

Required tools:

•

A Phillips screwdriver

A drill with an appropriately- sized drill bit for pre- drilling holes for the screw anchors.

CAUTION

Installation and servicing should be performed only by qualified

and experienced technicians to conform to all local codes and to maintain your

warranty.

Aiming the Camera and Adjusting Zoom and Focus

1. Aim the camera lens in the desired direction.

2. Tighten the adjustment screws to secure the camera lens in place.

3. Attach the dome cover to the camera and remove the protective film from the bubble.

4. S et the lens zoom and focus.

The camera connected to a PoE port of the Honeywell Embedded NVR can be configured

with the NVR directly.

To log on to the camera with a PC, perform the following steps:

a. Install the Honeywell Config Tool from the software and the documentation CD, find the

camera and open the web browser with the Honeywell Config Tool.

b. Log on to the camera as the admin user. The default user name is admin (case-

sensitive) and the default password is 1234.

c. Go to Setup



Camera



Conditions



Zoom and Focus. The following panel appears:

Preparing the Mounting Surface

1. Inspect the site where you want to install the camera. The mounting surface must be

flat and capable of supporting at least three times the weight of the camera.

2. Remove the backing from the mounting template sticker and affix the sticker to the

mounting surface.

Note If you are using the side exit for the cable, no te the orientation of the cab le exit no tch.

In out oor onsd ins l ital at the no r to t fr i tch should point downwa ds prevent wa er om enter ng

the ca i mera hous ng.

Document - 1 – – 800 2123 V1 Rev A 10/2015

© 5 this publication 201 Honeywell International Inc. All rights reserved. No part of may be reproduced by any means without written permission from Honeywell. The information in this publication is believed to be accurate in all respects. However,

Honeywell cannot assume responsibility for any consequences resulting from the use thereof. The information Revisions editions contained herein is subject to change without notice. or new to this publication may be issued such to incorporate changes.

3. Dr ho at lo tions a ill three screw les the ca indic ted on

t n ng tem te ic r he mou ti pla st ke and in t e th e ser th re

supplied pla ic an in holest chors the s.

4. If you ush nti c ra are fl mou ng the ame and want to

sto b i i re the ca les nside the wall or ceil ng, drill a hole

at the the ca ible ex t po tion on si i mount ng temp late

and ough the then pull the cables thr hole.

Mounting the Camera

1. Use su the p o t do co f the ra a ly set plied Allen key to rem ve he me ver rom came ssemb and it

aside.

a. Open the cover of the microSD card reader as shown in Figure 2-1.

b. Place the microSD card in the reader as shown in Figure 2-2, and then

close the cover.

3. Connect the camera with the Ethernet cable and the power cable.

a. Connect one end of the Ethernet cable to the RJ- 45 port on the camera.

b. - -If the other end of the Ethernet cable is NOT connected to a PoE (Power over

Ethernet) switch or NVR, connect the power connector of the camera to a 12 V DC

power source.

4. Attach the camera assembly to the mounting surface using the supplied screws.

• Click Zoom in + or Zoom out – to zoom in or out.

• Click Near – or Far + to focus near or far, or click Auto Focus to enable auto

focus.

2. If local storage is needed, insert a Micro SD card into the Micro SD card slot according to

the following steps:

Figure 2-1

Figure 2-2

Specyfikacje produktu

Marka:	Honeywell
Kategoria:	kamera bezpieczeństwa
Model:	H4D3PRV2
Kolor produktu:	Black, White
Rodzaj zasilania:	PoE
Wysokość produktu:	89 mm
Głębokość produktu:	122 mm
Waga produktu:	500 g
Technologia łączności:	Przewodowa
Bluetooth:	Nie
Certyfikaty:	FCC
Maksymalne zużycie mocy:	8.5 W
Liczba kamer:	1
Formaty kompresji:	H.264, M-JPEG
Obsługiwane typy kart pamięci:	MicroSDHC
Maksymalny rozmiar karty pamięci:	128 GB
Przeznaczenie:	Wewnętrz i na wolnym powietrzu
Standardy komunikacyjne:	IEEE 802.3af
Ilość portów Ethernet LAN (RJ-45):	1
Obsługa PoE:	Tak
Zakres temperatur (eksploatacja):	-30 - 60 °C
Zakres wilgotności względnej:	10 - 100 %
Układ:	Douszne
Automatyczne ustawienie ostrości:	Tak
Możliwość przybliżenia:	Tak
Tryb nocny:	Tak
Wi-Fi:	Nie
Przewodowa sieć LAN:	Tak
Zintegrowany czytnik kart:	Tak
Obsługiwane operacyjne systemy komórkowe:	Android, iOS
Szyfrowanie / bezpieczeństwo:	802.1x RADIUS
Model:	Kamera bezpieczeństwa IP
Technologia okablowania:	10/100Base-T(X)
Obsługa jakość serwisu (QoS):	Tak
Maks. rozdzielczość:	2304 x 1296 px
Stopień ochrony IP:	IP66
Typ mocowania:	Ściana
Stosunek sygnału do szumu:	50 dB
Długość ogniskowa:	2.7 - 12 mm
Obsługiwane rozdzielczości grafiki:	352 x 240,704 x 480,1280 x 720 (HD 720),1920 x 1080 (HD 1080),2304 x 1296
Obsługiwane tryby wideo:	720p, 1080p
Obsługa funkcji Plug & Play:	Tak
Typ przetwornika obrazu:	CMOS
Suma megapikseli:	3 MP
Balans bieli:	Auto, Manual
Typ migawki aparatu:	Elektroniczny
Tryb dzienny / nocny:	Tak
Typ diody LED:	Podczerwień
Min. Oświetlenie:	0.1 lx
Pełny HD:	Tak
Czujnik ruchu:	Tak
Ostrość:	Zmotoryzowana
Filtrowanie adresów IP:	Tak
Kąt widzenia obiektywu, w poziomie:	86 °
Wielkość czujnika CCD:	1/3 "
Maksymalna przesłona:	1.4
Ilość klatek:	30 fps
Szybkość migawki:	1/100000 s
Inkrypcja HTTS:	Tak
Podczerwień (IR) Filtr odcięcia:	Tak
Liczba użytkowników:	20 użyt.
Wyjście prądu stałego (w woltach):	12
Kompensacja oświetlenia tylnego:	Tak
Odległość widzenia nocnego (Night Vision):	30 m
Zdalny podgląd:	Tak
Cechy zabiezpieczeń:	Wodoodporna
Maska prywatności:	Tak
Prędkość przepływu danych:	4 - 8192 kbps