Instrukcja obsługi Fusion XS-S10SPGW

Fusion subwoofer XS-S10SPGW

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Fusion XS-S10SPGW (5 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/5

XS Series Subwoofer Installation Instructions .................................................................................. 2

Instructions d'installation du caisson de basse XS Series ................................................................ 6

Subwoofer XS Series Istruzioni di installazione .............................................................................. 10

Subwoofer der XS Series – Installationsanweisungen ................................................................... 14

Instrucciones de instalación del subwoofer de la XS Series ...........................................................18

XS Series da série esportiva da marca ...........................................................................................22

XS Series subwooferinstallatie-instructies ...................................................................................... 26

Garmin®, the Garmin logo, FUSION®, the Fusion logo, and True-Marine™ are trademarks of Garmin Ltd. or its subsidiaries, registered in the USA and other countries. These trademarks may not be used

without the express permission of Garmin.

October 2018

190-02481-91_0A

XS Series Subwoofer Installation

Instructions

Important Safety Information

WARNING

Failure to follow these warnings and cautions could result in

personal injury, damage to the vehicle or vessel, or poor product

performance.

See the guide in the Important Safety and Product Information

product box for product warnings and other important

information.

This device must be installed according to these instructions.

Disconnect the vehicle's or vessel's power supply before

beginning to install this product.

CAUTION

Continuous exposure to sound pressure levels over 100 dBA

may cause permanent hearing loss. The volume is typically too

loud if you cannot hear people speaking around you. Limit the

amount of time you listen at high volume. If you experience

ringing in your ears or muffled speech, stop listening and have

your hearing checked.

Always wear safety goggles, ear protection, and a dust mask

when drilling, cutting, or sanding.

NOTICE

When drilling or cutting, always check what is on the opposite

side of the surface.

It is strongly recommended that you have your audio system

installed by a professional installer to ensure optimum

performance.

You must read all installation instructions before beginning the

installation. If you experience difficulty during the installation, go

to for product support.www.fusionentertainment.com

After installing the subwoofer, you should run the subwoofer at

low to medium volumes for the first few hours of use. This helps

to improve the overall sound by gradually loosening up the

moving components of the subwoofer, such as the cone, spider,

and surround

What's In the Box

• 1 subwoofer

• 6 Phillips stainless steel, 4.8 mm x 50 mm (10 gauge x 2 in.)

mounting screws

• Mounting template

• Grilles

Tools Needed

• Electric drill

• Drill bit (size varies based on surface material)

• Phillips screwdriver

• Wire strippers

• Crimping tool

• Electrical tape

• Appropriate saw or utility knife to cut surface material

• Marine sealant (optional)

• Suitable gauge speaker wire for the length required

NOTE: For customized installations, additional tools and

materials may be needed.

Mounting Considerations

Selecting the correct mounting location is critical to optimize the

performance of the audio system. This FUSION® subwoofer is

designed to perform in the widest possible range of mounting

locations, but the more you plan the installation, the better the

subwoofer sound will be.

• The audio system must be turned off before making any

connections. Failure to do so could result in permanent

damage to the audio system.

• You should protect all terminals and connections from

grounding and from each other. Failure to do so could result

in permanent damage to the audio system and voids the

product warranty.

• You should protect the wires from sharp objects and always

use rubber grommets when wiring through panels.

• The mounting location must avoid potential obstacles, such

as fuel and hydraulic lines and wiring.

• The mounting location must provide sufficient clearance for

the mounting depth of the subwoofer as specified in the side

view drawings and the specifications.

• When possible, the area behind each subwoofer should be

enclosed.

• To avoid interference with a magnetic compass, the

subwoofer should not be installed closer to a compass than

the compass-safe distance value listed in the product

specifications.

• You should select a flat mounting surface for the best seal.

• For better bass performance, the subwoofer should be

mounted in an area that provides just enough room behind

the subwoofer. Too small an area restricts bass, and too

large an area compromises bass performance. Refer to the

specifications for optimum volume recommendations.

• When a subwoofer is not exposed to the outside

environment, a better bass performance can be achieved

using an enclosure that has a ported design.Theile Small

parameters are provided in the specifications to assist with

enclosure and port design.

• If you intend to mount the subwoofer outside the boat, follow

these considerations.

◦ When mounted correctly, the subwoofer is rated IP65 for

protection in the marine environment from the front of the

subwoofer. Water exposure and damage to the rear of the

subwoofer voids the warranty.

◦ The subwoofer must be mounted in a location well above

the waterline, where it is not submerged.

◦ The subwoofer must be mounted in a location where it

cannot be damaged by docks, pilings, or other pieces of

equipment.

◦ The subwoofer should be mounted in a sealed enclosure,

especially if it is exposed to wash down. A port or vent

may allow water to collect in the enclosure and damage

the subwoofer.

Mounting the Subwoofer

Before mounting the subwoofer, you must choose a location

following the mounting considerations above.

Before cutting the mounting surface, you should verify that there

is enough clearance for the speaker behind the surface. Refer to

the specifications for clearance information.

NOTICE

Do not apply grease or lubricant to the screws when fastening

the subwoofer to the mounting surface. Grease or other

lubricants can cause damage to the subwoofer housing.

1Route the wires from the source to the mounting location,

away from sources of electrical interference.

2Trim the template and make sure it fits in the selected

location.

3Orient the template so the FUSION logo is level in the

selected location.

2 Installation Instructions

4Secure the template to the selected location.

5Using a rotary tool or jigsaw, cut the mounting surface along

the inside of the line on the template.

6Place the subwoofer in the cutout to test the fit.

7If necessary, use a file and sandpaper to refine the size of

the cutout.

8After the subwoofer fits correctly in the cutout, ensure the

mounting holes on the subwoofer line up with the pilot holes

on the template.

9If the mounting holes on the subwoofer do not line up, mark

the new hole locations.

10 Using an appropriately sized drill bit for the mounting surface

and screw type, drill the holes.

11 Remove the template from the mounting surface.

12 Connect the subwoofer wires À while observing polarity

( ).Subwoofer Wiring, page 3

13 If necessary, connect the LED wires to the Sports model

subwoofer ( ).LED Wiring, page 3

14 Place the subwoofer in the cutout.

15 Secure the subwoofer to the mounting surface using the

included screws Á.

NOTE: Do not over tighten the screws, especially if the

mounting surface is not flat.

16 With the subwoofer mounted, hold the grille with the FUSION

logo at the bottom, or at the 6 o'clock position.

17 Press on the grille to snap it into place.

Subwoofer Wiring

When connecting the subwoofer to your amplifier or source,

observe the following considerations.

• Speaker wire is not included with the subwoofer. You should

use 20 AWG (0.52 mm2) speaker wire to connect the

subwoofer to the amplifier or source.

• The leads on the subwoofer are terminated using male spade

connectors. You should use female spade connectors (not

included) to connect the speaker wire to the speaker leads

for the best connection.

• The subwoofer features a dual 2 Ohm voice coil that can be

configured for 2.1 operation (two speakers and one

subwoofer) when connected to a FUSION stereo with DSP

capability (Configuring the Subwoofer for 2.1 Operation,

page 4).

• You can use the following table to identify the polarity of the

leads on the speaker.

White Positive (+)

Gray with a black stripe Negative (-)

NOTE: Gray and white with a black stripe wires are

connected to jumper terminals on the back of the subwoofer.

These wires must remain connected to the jumper terminals

for normal use (4 Ohm) and should be disconnected only

when configuring the speaker for 2.1 operation.

LED Wiring

Connecting the LED Wires

You can control the color of the LEDs by connecting the LED

color wires to ground. You can splice the ground wire to multiple

LED wires to customize the LED color.

NOTE: This feature is available only on the sports model.

NOTE: Instead of connecting the LED wires for one dedicated

color, you can install a remote control to turn the LEDs on and

off, change the color, and create lighting effects. See your

FUSION dealer or for more www.fusionentertainment.com

information.

The black wire on the LED cable is terminated with a 4 mm

female bullet connector, and the color wires are terminated with

4 mm male bullet connectors. You can connect these to 4 mm

bullet connectors on your wires (not included), or remove the

bullet connectors to connect to the bare wires instead.

1Connect a positive wire to the black wire on the LED cable.

2Connect a ground wire to the wire on the LED cable

according to the preferred LED color.

LED Color LED Wire Color

Red Red

Green Green

Blue Blue

Yellow Red and green

Magenta Red and blue

Cyan Blue and green

White Red, green, and blue

3Route the positive and negative wires, and connect them to a

power source (Connecting the LED Wires to Power,

page 3).

Connecting the LED Wires to Power

NOTE: This feature is available on only the sports model.

You must connect all 12 Vdc wiring to the LEDs to a 3 A fuse at

the power-source end of the cable. You should connect the

positive (+) power wire to a 12 Vdc power source through an

isolator switch or circuit breaker to turn the LEDs on and off. You

can use the same isolator or circuit breaker controlling the

power supply to your stereo, which allows you to turn the LEDs

and the stereo on and off at the same time.

You should use 22 AWG (0.33 mm2) or thicker wire to connect

the LEDs to the battery.

1Route the positive power (+) and negative ground (-) wires

from the LED-wire connections to the battery.

2Connect the negative wire to the negative (-) battery terminal.

3Connect the positive wire to the positive (+) terminal through

a 3 A fuse and isolator switch or circuit breaker.

Subwoofer Sound Optimization

While installing the subwoofer, you can ensure the sound from

the subwoofer is optimized by running the subwoofer out of

phase. You can switch the positive and negative wires on the

amplifier or source to run them out of phase.

Running the subwoofer out of phase from the speakers allows

you to hear if the perception of bass is more from the location of

the subwoofer or from the speakers. If running the subwoofer

out of phase gives a better perception that the bass is from the

speakers’ location, then out-of-phase wiring is correct for your

system.

You can run the subwoofer out of phase by temporarily

switching the positive and negative connections from the

subwoofer at the amplifier or source. Depending on the outcome

of the test, you can then switch the connections back if

necessary.

Installation Instructions 3

Specyfikacje produktu

Marka:	Fusion
Kategoria:	subwoofer
Model:	XS-S10SPGW

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Fusion XS-S10SPGW, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje subwoofer Fusion

Fusion CS-AT1100 Instrukcja

22 Września 2024

Fusion XS-SL10SPGW Instrukcja

18 Września 2024

Fusion SG-SL122SPC Instrukcja

16 Września 2024

Fusion XS-S10SPGW Instrukcja

16 Września 2024

Fusion SG-SL102SPC Instrukcja

15 Września 2024

Fusion SG-S102W Instrukcja

14 Września 2024

Fusion MS-SW10 Instrukcja

14 Września 2024

Fusion XS-S10CWB Instrukcja

13 Września 2024

Fusion SG-SL122SPW Instrukcja

13 Września 2024

Fusion FM-S10SB Instrukcja

13 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

JL Audio SGR-10TW3 Instrukcja

13 Października 2024

Teufel T6 Instrukcja

13 Października 2024

Polk DB1040 Instrukcja

10 Października 2024

OSD Audio NERO DUAL X8 Instrukcja

9 Października 2024

OSD Audio NERO WSA Instrukcja

9 Października 2024

Kicker 51CWQ102 Instrukcja

9 Października 2024

Kicker 51CWQ122 Instrukcja

9 Października 2024

Kicker 43C84 Instrukcja

9 Października 2024

Kicker 51CWQ124 Instrukcja

9 Października 2024

OSD Audio FS12 Instrukcja

9 Października 2024