Instrukcja obsługi JL Audio FS108-W5

JL Audio subwoofer FS108-W5

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla JL Audio FS108-W5 (1 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
1. Unpack the enclosure and
determine where it will be
mounted. Consider access to the
opposite side of the mounting
surface to secure the mounting
bolts and for visual conrmation
you are not drilling through any
wires, hoses or even the hull of
the vessel. In addition, consider
the structural integrity of the
mounting surface itself and that
installation does not interfere with
water drainage, hatch lids, or any
moving parts on the vessel.
2. Using a Phillips-head screwdriver,
remove the 3 Stainless-Steel screws
that mount the woofer to the
enclosure and remove the woofer.
3. Mark the enclosure for the
location of the mounting holes.
There should be at least 2
mounting bolts used to secure the
enclosure (3 or more mounting
bolts are recommended for extra
strength and stability). On the
inside of the enclosure, ensure
there is ample room around the
mounting points for the mounting
hardware (not included).
4. In addition to the mounting holes,
one additional hole must be
marked for the entry of the speaker
wire into the enclosure. For this
hole, consider the most clean and
protected wire run (this may mean
the top or back of the enclosure).
5. Drill a pilot hole into the
enclosure at each of the marks
made in Step 3. Enlarge each
pilot hole to the appropriate
diameter, as dictated by the
mounting hardware and speaker
cable used.
6. Once all of the holes are drilled
through the enclosure, hold it
in the exact mounting location
determined in Step 1. Using the
holes drilled in as a guide, Step 5
mark the mounting surface so
that corresponding enclosure
mounting holes can be drilled.
7. At each mark made in Step
6 , drill pilot holes and then
appropriately-sized mounting
holes into the mounting surface.
8. Run the wire into the enclosure
leaving 18" within the enclosure
so that the woofer can be easily
wired and mounted. Fill the hole
through which the wire is run
with silicone caulk to both seal
the enclosure and protect the
wire from abrasion.
9. Securely mount the enclosure
using the mounting hardware and
seal the enclosure at the mounting
holes with a silicone caulk.
10. Make the terminal connections to
the woofer observing the correct
polarity and set the woofer in the
enclosure’s woofer mounting hole.
Orient the woofer’s logo so it is
appropriate for the installation
and so that each of the woofers
mounting holes line up with the
pre-drilled holes in the enclosure.
Re-mount the woofer using the
3 Stainless-Steel screws removed
in Step 2 and the 3 additional
Stainless-Steel screws included
with the enclosure.
11. You have completed the
installation. Enjoy your
new Enclosed Marine
Subwoofer System.
For questions concerning installation of
this product, contact JL Audio Technical
Support during regular business hours at
(954) 443-1100.
The FS108-W5 and FS110-W5 are designed to be a universal-application
Subwoofer Systems. The exact mounting procedure employed will vary
based on the requirements of the installation. The steps outlined in
these instructions take most considerations into account and should be
read thoroughly prior to beginning your installation.
FS108-W5 / FS110-W5
Installation Instructions
Reccomended Hardware/Mounting
(Stainless-Steel)
ENCLOSURE WALL
MOUNTING SURFACE
Fender Washer
Fender Washer
Lock Washer
Hex Nut
Hex Head Bolt
Silicone Sealant
Printed in U.S.A. 120117


Specyfikacje produktu

Marka: JL Audio
Kategoria: subwoofer
Model: FS108-W5

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z JL Audio FS108-W5, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje subwoofer JL Audio

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer