Instrukcja obsługi EnGenius EWS385AP


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla EnGenius EWS385AP (6 stron) w kategorii Punkt dostępu. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/6
Quick Installation Guide
Package Contents
Minimum Requirements
+ Broadband Internet Service
(Cable or DSL Modem)
(Internet Explorer, Safari, Firefox, Chrome, Edge)
+Internet Browser
(To use with EWS Series Management Switches)
+EnGenius Wireless Management L2 Switch
Managed Access Point Installation with Wireless Management Switch
Tri-Band Wireless Indoor Access Point
Quick Installation Guide
EWS385AP
version l.0
1Connecting the Access Point
(Through EnGenius Wireless Management Switch)
A)
B)
Connect one end of the on the front Ethernet Cable into an Ethernet Port
panel of the EnGenius Wireless Management Switch and the other end to the
Ethernet Port on the computer.
Connect another into the of the Managed AP Ethernet Cable LAN Port
and the other end to the on the Wireless Management Switch. Ethernet Port
With the Wireless Management Switches, the Managed AP is able to obtain
proper assigned IP address for further configurations.
C)
D)
Users may create several clusters simultaneously to accommodate
their deployments under .AP Clusters
For distinct settings, EnGenius Wireless Management switches still
off er individual Managed Access Point customization for cluster
members such as diff erent channels that best adapt your local WLAN
deployments.
2IP Address Configuration
B)
A) Once your computer is on, ensure that
your TCP/IP is set to or . On Enabled
Open Network Connections and then click
Local Area Connection Internet . Select
Protocol Version 4 (TCP/IPv4)
If your computer is already on a network,
ensure that you have set it to a Static IP
Address on the interface.
(Example: 192.168.0.88 and the Subnet
Mask address as 255.255.255.0.)
A)
B)
3Management Switch Setup
C)
Open a web browser on your computer. In the address bar of the web
browser, enter and .192.168.0.239 enter
The EnGenius Wireless Management Switch User Interface will appear.
Make sure the is set to .Controller State Enabled
A login screen will appear. By default, username is and the admin
password is . Enter the current username and password of password
the Wireless Management Switch and then click .Login
Your model number may be
different in the web browser
interface.
*
5
Conguring Managed AP
(Through EnGenius Wireless Management Switch GUI)
A)
B)
Confi gure Managed AP(s) through the GUI interface from the switch for
WLAN settings under . Click the “Device Name” in Device Management
order to confi gure your Managed AP.
Add Managed AP(s) to specifi c to save repetitive configuration AP Cluster
tasks.
88:DC :96:0D:C6:E0
EWS310AP
EWS310APOnline 88:DC:96:0D:C6:E0 EWS310AP 192.168.0.12
EWS320APOnline 88:DC:96:01:9B:86 EWS320AP 192.168.0.11
4 Adding Managed AP
(Through EnGenius Wireless Management Switch GUI)
A) All Managed AP(s) connected to the same network as the Wireless
Management Switch will appear on the right side of the screen, under
the Access Point list. Locate and select the Managed AP(s) Detected
AP by checking the box and click to manage the device.Add
B) You may confi gure your Managed AP(s) after you successfully
connected to the Wireless Management Switch through its .GUI
EWS310AP 88:DC:96:0D:C6:E0 EWS310AP 192.168.0.12
EWS320AP 88:DC:96:01:9B:86 EWS320AP 192.168.0.11
EWS320AP
88:DC: 96:01 :9B:86
EWS310AP
88:DC: 96:0D: C6:E0
EWS310AP
Technical Support
Country of Purchase
Service Center
Service Information
North America Canada
Los Angeles, USA
support@engeniusnetworks.eu
(+31) 40 8200 887
technology@senao.com
Europe Netherlands
Africa
CIS
Middle East
Russia
www.engeniustech.com.sg
www.engenius-me.com
www.engeniusnetworks.eu
www.engeniustech.com
www.engeniuscanada.com
Dubai, UAE
Asia
Oceania
Singapore
Taiwan, R.O.C
Others
www.engeniusnetworks.com
Notes
Maximum data rates are based on the IEEE standards. Actual throughput and range may vary depending on
many factors including environmental conditions, distance between devices, radio interference in the
operating environment, and mix of devices in the network. Features and specications subject to change
without notice. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation. Trademarks and
registered trademarks are the property of their respective owners. For United States of America: Copyright
©2019 EnGenius Technologies, Inc. All rights reserved.
rma@engeniuscanada.comToll
Free: (+1) 888 397 2788Local:
(+1) 905 940 8181
support@engeniustech.comToll
Free: (+1) 888 735 7888Local:
(+1) 714 432 8668
support@engenius-me.com
Toll Free:
U.A.E.: 800-EnGenius
800-364-364-87
General: (+971) 4 357 5599
support@engeniustech.com
Toll Free: (+1) 888 735 7888
Local: (+1) 714 432 8668
Stand-alone Access Point Installation
EWS385AP
Tri RadioAP+2T2R, 400Mbps+867Mbps+867Mbps
EWS385AP
2 IP Address Configuration
A)
B)
A)
B)
1
Connecting the Access Point
A)
3
Access Point Setup
C)
B)
.
Connect one end of the into the of the Ethernet cable LAN port
Access Point and the other end to the on the computer.Ethernet port
Once your computer is on, ensure that
your TCP/IP is set to or . On Enabled
Open Network Connections and then
click . SelectLocal Area Connection
Internet Protocol Version 4 (TCP/IPv4).
Open a web browser on your computer.
In the address bar of the web browser,
enter and .192.168.1.1 enter
A login screen will appear. By default,
the username of the Access Point is
admin admin and the password is
Enter the current username and
password of the Access Point and
then click .Login
The EnGenius Access Point User Interface will appear. This device
can operate in Access Point operating mode.
* Your model number may be diff erent in the web browser interface.
If your computer is already on a
network, ensure that you have set it to
a Static IP Address on the interface.
(Example: 192.168.1.10 and the
Subnet Mask address as
255.255.255.0.)
Connect the to the of the Access Point and Power Adapter DC-IN port
plug the other end into an electrical outlet.
Note: IEEE 802.3at The Access Point supports both PoE ( Power over
Ethernet ) or the included power adapter. You may use either one as the
power source. DO NOT use both at the same time. EWS385AP


Specyfikacje produktu

Marka: EnGenius
Kategoria: Punkt dostępu
Model: EWS385AP

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z EnGenius EWS385AP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Punkt dostępu EnGenius

EnGenius

EnGenius ECW220S Instrukcja

17 Września 2024
EnGenius

EnGenius EWS385AP Instrukcja

14 Września 2024
EnGenius

EnGenius ETA1305 Instrukcja

10 Września 2024
EnGenius

EnGenius ECB9500 Instrukcja

4 Września 2024
EnGenius

EnGenius EAP300 Instrukcja

27 Sierpnia 2024
EnGenius

EnGenius EWS871AP Instrukcja

24 Sierpnia 2024
EnGenius

EnGenius ECW336 Instrukcja

23 Sierpnia 2024
EnGenius

EnGenius EWS510AP Instrukcja

21 Sierpnia 2024
EnGenius

EnGenius EAP1200H Instrukcja

20 Sierpnia 2024

Instrukcje Punkt dostępu

Najnowsze instrukcje dla Punkt dostępu

Cisco

Cisco MR12 Instrukcja

14 Października 2024
Draytek

Draytek VigorAP 920R Instrukcja

13 Października 2024
Netgear

Netgear WNDAP360 Instrukcja

12 Października 2024
TP-Link

TP-Link Festa F65-Wall Instrukcja

9 Października 2024
D-Link

D-Link DWL-1000AP+ Instrukcja

9 Października 2024
D-Link

D-Link DWL-700AP Instrukcja

9 Października 2024