Instrukcja obsługi DBX DDP
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla DBX DDP (40 stron) w kategorii edytor. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/40
DDP
DDP
DDP
DDPDDP
Digital Dynamics Processor
®
Operator Manual
WARNING
FOR YOUR PROTECTION, PLEASE READ THE FOLLOWING:
WATER AND MOISTURE: Appliance should not be used near water (e.g. near a bathtub, wash-
bowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool, etc). Care should
be taken so that objects do not fall and liquids are not spilled into the enclosure through open-
ings.
POWER SOURCES: The appliance should be connected to a power supply only of the type
described in the operating instructions or as marked on the appliance.
GROUNDING OR POLARIZATION: Precautions should be taken so that the grounding or polar-
ization means of an appliance is not defeated.
POWER CORD PROTECTION: Power supply cords should be routed so that they are not likely to
be walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the appliance.
SERVICING: To reduce the risk of fire or electric shock, the user should not attempt to service
the appliance beyond that described in the operating instructions. All other servicing should be
referred to qualified service personnel.
FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE: Replace fuse
with same type and rating only.
MULTIPLE-INPUT VOLTAGE: This equipment may require the use of a different line cord, attach-
ment plug, or both, depending on the available power source at installation. Connect this equip-
ment only to the power source indicated on the equipment rear panel. To reduce the risk of fire
or electric shock, refer servicing to qualified service personnel or equivalent.
SAFETY INSTRUCTIONS
NOTICE FOR CUSTOMERS IF YOUR UNIT IS EQUIPPED WITH A POWER CORD.
WARNING: THIS APPLIANCE MUST BE EARTHED.
The cores in the mains lead are coloured in accordance with the following code:
GREEN and YELLOW - Earth BLUE - Neutral BROWN - Live
As colours of the cores in the mains lead of this appliance may not correspond with
the coloured markings identifying the terminals in your plug, proceed as follows:
• The core which is coloured green and yellow must be connected to the ter-
minal in the plug marked with the letter E, or with the earth symbol, or
coloured green, or green and yellow.
• The core which is coloured blue must be connected to the terminal marked
N or coloured black.
• The core which is coloured brown must be connected to the terminal
marked L or coloured red.
This equipment may require the use of a different line cord, attachment plug, or
both, depending on the available power source at installation. If the attachment
plug needs to be changed, refer servicing to qualified service personnel who
should refer to the table below. The green/yellow wire shall be connected direct-
ly to the unit's chassis.
WARNING: If the ground is defeated, certain fault conditions in the unit or in the
system to which it is connected can result in full line voltage between chassis and
earth ground. Severe injury or death can then result if the chassis and earth
ground are touched simultaneously.
LIVE
E
NEUTRAL
EARTH GND
CONDUCTOR
L
N
BROWN
BLUE
GREEN/YEL
BLACK
Normal Alt
WIRE COLOR
WHITE
GREEN
U.K. MAINS PLUG WARNING
A
moulded mains plug that has been cut off from the cord is unsafe. Discard
the mains plug at a suitable disposal facility. NEVER UNDER ANY CIRCUM-
STANCES SHOULD YOU INSERT A DAMAGED OR CUT MAINS PLUG INTO A
13 AMP POWER SOCKET. Do not use the mains plug without the fuse cover
in place. Replacement fuse covers can be obtained from your local retailer.
Replacement fuses are 13 amps and MUST be ASTA approved to BS1362.
The symbols shown above are internationally accepted symbols that warn of
potential hazards with electrical products. The lightning flash with arrowpoint in
an equilateral triangle means that there are dangerous voltages present within the
unit. The exclamation point in an equilateral triangle indicates that it is necessary
for the user to refer to the owner’s manual.
These symbols warn that there are no user serviceable parts inside the unit. Do
not open the unit. Do not attempt to service the unit yourself. Refer all servicing
to qualified personnel. Opening the chassis for any reason will void the manufac-
turer’s warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off
immediately and take it to a dealer for service. Disconnect the unit during storms
to prevent damage.
C A U T I O N
A T T E N T I O N : R I S Q U E D E C H O C E L E C T R I Q U E - N E P A S O U V R I R
W A R N I N G : T O R E D U C E T H E R I S K O F F I R E O R E L E C T R I C
S H O C K D O N O T E X P O S E T H I S E Q U I P M E N T T O R A I N O R M O I S T U R E
R I S K O F E L E C T R I C S H O C K
D O N O T O P E N
ELECTROMAGNETIC COMPATIBILITY
This unit conforms to the Product Specifications noted on the Declaration of Conformity.
Operation is subject to the following two conditions:
• this device may not cause harmful interference, and
• this device must accept any interference received, including interference that
may cause undesired operation.
Operation of this unit within significant electromagnetic fields should be avoided.
• use only shielded interconnecting cables.
DECLARATION OF CONFORMITY
Manufacturer’s Name: dbx Professional Products
Manufacturer’s Address: 8760 S. Sandy Parkway
Sandy, Utah 84070, USA
declares that the product:
dbx DDP
conforms to the following Product Specications:
Safety: EN 60065 (1993)
IEC65 (1985) with Amendments 1, 2, 3
EMC: EN 55013 (1990)
EN 55020 (1991)
Supplementary Information:
The product herewith complies with the requirements of
the Low Voltage Directive 73/23/EEC and the EMC
Directive 89/336/EEC as amended by Directive
93/68/EEC.
dbx Professional Products
Vice-President of Engineering
8760 S. Sandy Parkway
Sandy, Utah 84070, USA
March 31,1998
European Contact: Your Local dbx Sales and Service Oce or
International Sales Oce
68 Sheila Lane
Valparaiso, Indiana
46383, USA
Tel: (219) 462-0938
Fax: (219) 462-4596
Section 1: Introduction . . . . . . . . . . .2
Unpack . . . . . . . . . . . . . . . . . . . . . . . .2
Quickstart . . . . . . . . . . . . . . . . . . . . . . .2
Section 2: The DDP Tour . . . . . . . . .3
Hardware . . . . . . . . . . . . . . . . . . . . . . .3
Front Panel / Display . . . . . . . . . . . . .3
Rear Panel . . . . . . . . . . . . . . . . . . . .3
Signal Flow . . . . . . . . . . . . . . . . . . . .4
Software . . . . . . . . . . . . . . . . . . . . . . . .5
Setups and Programs . . . . . . . . . . . .5
Gate Section . . . . . . . . . . . . . . . . . . .5
Compressor Section . . . . . . . . . . . . . .5
De-essing Section . . . . . . . . . . . . . . .5
Limiting Section . . . . . . . . . . . . . . . . .5
Sidechain EQ Section . . . . . . . . . . . . .5
Section 3: Setup / Basic Operation . .6
Analog Connections . . . . . . . . . . . . . . . .6
Digital Connections . . . . . . . . . . . . . . . . .6
Midi Connections . . . . . . . . . . . . . . . . . .7
The Curve Window . . . . . . . . . . . . . . . . .7
Software Navigation . . . . . . . . . . . . . . . .8
Threshold Metering . . . . . . . . . . . . . .8
Operating Modes . . . . . . . . . . . . . . . .9
Program Mode . . . . . . . . . . . . . .9
The Bypass Button . . . . . . . . . . .10
Setup Mode . . . . . . . . . . . . . . . .10
Ext. S-chain and the Digital Meters .11
Viewing Elements of a Chain . . . . .13
Linked Programs . . . . . . . . . . . .13
Dual-mono Programs . . . . . . . . .13
Section 4: Editing/Recalling/Saving
Presets . . . . . . . . . . . . . . . . . . . 14
The Store Button . . . . . . . . . . . . . . . . . .14
Moving Around . . . . . . . . . . . . . . . . . . .14
Editing Gates . . . . . . . . . . . . . . . . . . . .14
Editing Compressors . . . . . . . . . . . . . . .15
Editing Limiters . . . . . . . . . . . . . . . . . . .17
Editing De-Essers . . . . . . . . . . . . . . . . . .18
Editing the Sidechain EQ . . . . . . . . . . . . .18
More About Sidechain EQ . . . . . . . . . . . .19
Changing Chain Types . . . . . . . . . . . . . . .20
Saving Programs and Setups . . . . . . . . . .20
Saving a Program . . . . . . . . . . . . . . .20
Saving a Setup . . . . . . . . . . . . . . . . .21
Replace Old . . . . . . . . . . . . . . . .21
Store New . . . . . . . . . . . . . . . . .21
Section 5: Utility Functions . . . . . . .23
Contrast . . . . . . . . . . . . . . . . . . . . . . .23
Sample Rate . . . . . . . . . . . . . . . . . . . . .23
AutoLoad . . . . . . . . . . . . . . . . . . . . . . .23
Digital Input Mode . . . . . . . . . . . . . . . . .23
Digital Output Mode . . . . . . . . . . . . . . . .24
Digital Input Level Controls . . . . . . . . . . .24
MIDI . . . . . . . . . . . . . . . . . . . . . . . .24
SysEx . . . . . . . . . . . . . . . . . . . . . . .24
A/D Calibration . . . . . . . . . . . . . . . . . . .24
Section 6: Appendices . . . . . . . . . . .25
A
PPENDIX
1: Misc. Information . . . . . . . . .25
Hard Reset . . . . . . . . . . . . . . . . . . .25
Change Default Startup Program . . . . .25
Front Panel Lockout . . . . . . . . . . . . .25
TYPE IV™ Conversion System . . . . . . .25
TSE™ Tape Saturation Emulation . . . . .25
TCM™ Transient Capture Mode . . . . .26
A
PPENDIX
2: Factory Setup Listing . . . . . . .27
A
PPENDIX
3: Factory Program Listing . . . .29
A
PPENDIX
4: MIDI/SysEx/CC Guide . . . . . .30
Midi Basics . . . . . . . . . . . . . . . . . . . . .30
MIDI Channels . . . . . . . . . . . . . . . . .30
MIDI Changes . . . . . . . . . . . . . . . . .30
Continuous Controller Listing . . . . . . . . . .30
S
YS
E
X
Basics . . . . . . . . . . . . . . . . . . . .31
General Format . . . . . . . . . . . . . . . .31
Hex Value Definitions . . . . . . . . . . . . .31
Procedures . . . . . . . . . . . . . . . . . . .31
SysEx Program Dump Sample . . . . . . .34
A
PPENDIX
5: Factory Service / Warranty . . .35
A
PPENDIX
6: Specifications . . . . . . . . . . . .36
DDP
DDP
DDP
DDPDDP
Digital Dynamics Processor
Manual Contents
1
Specyfikacje produktu
| Marka: | DBX |
| Kategoria: | edytor |
| Model: | DDP |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z DBX DDP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje edytor DBX
30 Września 2024
20 Września 2024
12 Września 2024
12 Września 2024
27 Sierpnia 2024
26 Sierpnia 2024
9 Sierpnia 2024
Instrukcje edytor
- edytor Hikvision
- edytor Roland
- edytor Bose
- edytor Asus
- edytor Allen & Heath
- edytor HP
- edytor Heritage Audio
- edytor Datapath
- edytor Zoom
- edytor TC Helicon
- edytor Vivolink
- edytor Eventide
- edytor Smart-AVI
- edytor Ashly
- edytor Gefen
- edytor SEADA
- edytor Radial Engineering
- edytor Lectrosonics
- edytor Neutrik
- edytor SPL
- edytor RGBlink
- edytor Rupert Neve Designs
- edytor Dangerous Music
- edytor Matrox
- edytor Intel
- edytor Golden Age Project
- edytor Sonifex
- edytor Solid State Logic
- edytor Mathew Lane
- edytor Warm Audio
- edytor Drawmer
- edytor SIIG
- edytor Manley
- edytor MuxLab
- edytor Helix
- edytor Christie
- edytor Rane
- edytor AMD
- edytor Lexicon
- edytor Empirical Labs
- edytor AudioThing
- edytor Avenview
- edytor FabFilter
- edytor Metric Halo
- edytor Henry Engineering
- edytor MyMix
Najnowsze instrukcje dla edytor
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
8 Października 2024
7 Października 2024
7 Października 2024
7 Października 2024