Instrukcja obsługi Datalogic 94A151107

Datalogic Ładowarka do urządzenia mobilnego 94A151107

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Datalogic 94A151107 (2 stron) w kategorii Ładowarka do urządzenia mobilnego. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/2
ACCESSORIES
94A051013 WIN-NET VEHICLE POWER
CAB (CRADLE)
Cable containing an 8A slow-blow fuse for powering
the vehicle cradle from the car cigarette lighter.
94ACC1306 ADJUSTABLE ARM KIT FOR
VEHICLE CRADLE
positionable arm for mounting the cradle in the
vehicle.
TECHNICAL FEATURES
Kyman-NET™ Vehicle Cradle
Electrical Features
Power Supply from 10 to 32 VDC
Consumption (with mobile computer) Max. 1.8 A
Quiescent Consumption
(without mobile computer) Max. 5 mA
Indicators Power on LED (green)
Charge Time
(when mobile computer is off) Li-Ion Battery: max. 2.5 hours
Communication Features
Interface RS232
Baud Rate up to 115200 b/sec
Environmental Features
Working Temperature* -20° to +50 °C / -4° to +140 °F
Storage Temperature -20° to +70 °C / -4° to +158 °F
Humidity 90% non condensing
Degree of Protection IP20
Vibration Resistance EN60068-2-64 frequency range 5-1000 Hz; acceleration
RMS: 3.1 g; initial slope: 26dB/oct 5-10 Hz; final slope: -3dB/oct 10-1000 Hz
Shock Resistance EN60068-2-29 – ±25g, 6ms duration, 500 shock impacts per axis
Mechanical Features
Dimensions 118.5 x 321 x 104 mm / 4.66 x 12.63 x 4.09 in
Weight about 770 g / 27.16 oz
* Battery must be charged at a temperature ranging from 0° to +45 °C (+32° to +113 °F).
FCC COMPLIANCE
Modifications or changes to this equipment without the expressed written approval of Datalogic could void
the authority to use this equipment.
The device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference which may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant
to part 15 of the FCC Rules. These limits are des protection against harmful igned to provide reasonable
interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
822000692 (Rev. B)
Kyman-NET™ Vehicle Cradle
The Kyman-NET™ Vehicle Cradle allows charging the Kyman-NET™ mobile computer battery and
holding it securely in your vehicle. It also functions as a serial communication interface between a Host
(typically a Laptop PC) and the RS232 contacts on the mobile computer.
H
D
G
F
C
B
E
A
I
A) Microphone
B) Loudspeaker
C) Ext. Microphone/Headset Jack
D) LED Indicator
E) Mobile Computer Contacts
F) Mounting Holes
G) Adhesive Stylus Holder
H) Power Connector (Jack)
I) RS232 Connector
Figure 1 – Kyman-NET™ Vehicle Cradle
External microphone/headset jack, microphone and speaker allow managing a vocal communication (see
related paragraph on next page).
MOUNTING THE KYMAN-NET™ VEHICLE CRADLE
The Kyman-NET™ Vehicle Cradle can be mounted to the
desired surface using the 4 screws together with the 4 nuts.
Figure 2 – Mounting the Kyman-NET™ Vehicle Cradle
POWERING THE KYMAN-NET™ VEHICLE CRADLE
Once the cradle has been mounted, it is necessary to prepare the power cable termination to connect the
cradle to the vehicle power source.
− Brown wire: connect to a V+ (10 to 32 Vdc) vehicle power source;
− Blue wire: connect to the vehicle ground wire or chassis ground;
− Green/Yellow wire: not connected.
Figure 3 – Fuse Holder
For connection to the vehicle power source it is
possible to use the in-line fuse (with holder)
supplied with the cradle.
Verify that the a 8 A slow-blow fuse is contained
within the holder, then splice it to the end of the
brown wire of the cable. Make the distance
between fuse holder and power connection point as
short as possible and apply a caution label on the
fuse holder.
Once the power cable termination has been
completed, it is possible to connect the Kyman-
NET™ Vehicle Cradle to the vehicle power.
Figure 4 – Fuse Holder Connection
INSERTING THE KYMAN-NET™ INTO THE VEHICLE CRADLE
For correct functioning, first insert the
mobile computer into the cradle. Then,
push it towards the upper part of the cradle
until the retaining roller clicks.
When the cradle is powered, insert the
mobile computer and the green LED will
turn on. If the mobile computer is not
inserted, the LED remains off while the
cradle is still powered.
Click
Figure 5 – Inserting the Mobile Computer into the Kyman-NET™ Vehicle Cradle
EXTRACTING THE KYMAN-NET™ FROM THE VEHICLE CRADLE
To extract Kyman-NET™, push the clip o
f
the retaining roller up and extract the
mobile computer.
Figure 6 – Extracting the Mobile Computer from the Kyman-NET™ Vehicle Cradle
CONNECTION
The Kyman-NET™ Vehicle Cradle can be connected to a host by means of an RS232 interface.
RS232 Connection
The Kyman-NET™ Vehicle Cradle can be connected to the host by means of any standard null-modem
cable. A 9-pin female D-Sub connector must be connected to the RS232 port of the cradle. Once the host
has been turned on, insert the Kyman-NET™ mobile computer into the cradle.
Pin 9 of the Vehicle Cradle RS232 connector (normally not connected in null-modem cables), supplies
regulated +5 Vdc ± 5% 500 mA max power.
Figure 7 - RS232 Connection
Pinout
The Null Modem Cable allowing the RS232 connection has the following pinout:
DCD
RXD
TXD
DTR
GND
DSR
RTS
+5 V
CTS
RTS
1
2
3
7
3
2
4 6
5 5
4
8
6
7
1
Cradle side
9-pin D-sub
(
male
)
99
Host/PC side
9-pin D-sub
(
female
)
8
Figure 8 – Null Modem Cable Pinout
CONFIGURING KYMAN-NET™ MOBILE COMPUTER FOR VOCAL COMMUNICATION
By default vocal communication takes place through the Kyman-NET™ Mobile Computer integrated
loudspeaker and microphone. Once inserted into the vehicle cradle, the communication has to be
managed by the cradle itself. Thus, the mobile computer must be configured through the volume settings
applet available in the Windows CE .NET control panel to correctly manage the communication (refer to
the Kyman-NET™ User’s Manual for more details).
NOTE
Vocal Communication requires Kyman-NET™ Mobile Computer SW version 1.34
or later.
Fuse
Brown Wire
1
2
Host Computer
Standard Null-
Modem Cable
Kyman-NET™
Vehicle Cradle
To Vehicle Battery

Specyfikacje produktu

Marka: Datalogic
Kategoria: Ładowarka do urządzenia mobilnego
Model: 94A151107

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Datalogic 94A151107, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Ładowarka do urządzenia mobilnego Datalogic

Datalogic

Datalogic 94A151107 Instrukcja

3 Września 2024
Datalogic

Datalogic 94A151115 Instrukcja

29 Sierpnia 2024
Datalogic

Datalogic 94A151132 Instrukcja

4 Lipca 2024

Instrukcje Ładowarka do urządzenia mobilnego

Najnowsze instrukcje dla Ładowarka do urządzenia mobilnego

Tripp Lite

Tripp Lite CSC32USBW Instrukcja

15 Stycznia 2025
Mophie

Mophie speedport 120 Instrukcja

13 Stycznia 2025
Kogan

Kogan KACHG120PDA Instrukcja

7 Stycznia 2025
Ansmann

Ansmann HC130PD mini Instrukcja

5 Stycznia 2025
Ikea

Ikea NORDMÄRKE 104.916.58 Instrukcja

5 Stycznia 2025
Ikea

Ikea LIVBOJ 004.574.95 Instrukcja

5 Stycznia 2025
Ikea

Ikea NORDMÄRKE 604.780.65 Instrukcja

5 Stycznia 2025
Ikea

Ikea NORDMÄRKE 204.900.12 Instrukcja

5 Stycznia 2025
Ikea

Ikea LIVBOJ 404.470.51 Instrukcja

5 Stycznia 2025
Ikea

Ikea SJÖMÄRKE 705.163.97 Instrukcja

5 Stycznia 2025