Instrukcja obsługi CyberPower Value 1200E

CyberPower zasilacz UPS Value 1200E

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CyberPower Value 1200E (2 stron) w kategorii zasilacz UPS. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

Value 1200E-GP/1500E-GP/2200E-GP

User’s Manual

K01-0000142-00

This manual contains important instructions that should be followed during installation and maintenance of

the UPS and batteries. Please read and follow all instructions carefully during installation and operation of

the unit. Read this manual thoroughly before attempting to unpack, install, or operate.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker

protection. DO NOT plug the UPS into an outlet that is not grounded. If you need to de-energize this

equipment, turn off and unplug the UPS.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does

not sell products for life support or medical applications. DO NOT use in any circumstance that would affect

the operation or safety of any life support equipment, with any medical applications, or patient care.

CAUTION! The battery can energize hazardous live parts inside even when the AC input power is

disconnected.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor

area, free of conductive contaminants. (Please see specifications for acceptable temperature and humidity

range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery. There

are no user serviceable parts inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before

servicing the battery or installing a computer component.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near

aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause

the machine to short out.

UNPACKING

The box should contain the following:

(1) UPS Unit x 1; (2) IEC Power Cord x 1; (3) IEC to AU Adapter Cable x 2; (4) USB Cable x 1; (5) Phone

Cable x 1 (6) User Manual x 1; (7) Management Software Disk x 1

OVERVIEW

The Value 1200E-GP/1500E-GP/2200E-GP provides automatic voltage regulation for inconsistent utility

power. The Value 1200E-GP/1500E-GP/2200E-GP features 910 Joules of surge protection, and provides

battery backup during power outages. The Value 1200E-GP/1500E-GP/2200E-GP ensures consistent power

to your computer system and its included software will automatically save your open files and shut down your

computer system during a utility power loss.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR

EQUIPMENT

1. Ensure that the equipment plugged into the battery power-supplied/surge outlets does not exceed the

UPS unit’s rated capacity (1200VA/720W for Value 1200E-GP, 1500VA/900W for Value 1500E -GP,

2200VA/1320W for Value 2200E-GP). If the rated unit capacities are exceeded, an overload condition

may occur and cause the UPS unit to shut down or the fuse blow.

2. There are many factors that can affect the amount of power that your computer system will require. For

optimal system performance keep the load below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8

hours is recommended to ensure that the battery's maximum charge capacity is achieved. Charge loss

may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into an AC

outlet. The unit will charge in both the on and off position.

2. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data

storage device (Zip drive, Jazz drive, Tape drive, etc. into the battery power supplied outlets. DO NOT

plug a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device

into the battery power supplied outlets. The power demands of these devices will overload and

possibly damage the unit.

3. To protect a fax, telephone, modem line or network, connect a telephone cable or network cable from the

wall jack outlet to the IN jack of the UPS. Then connect a telephone cable or network cable from the OUT

jack on the UPS to the modem, computer, telephone, fax machine, or network device.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.

air conditioner, refrigerator, copier, etc. Avoid using extension cords.

5. Depress the power switch to turn the unit on. The power on indicator light will illuminate and the unit will

"beep".

6. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,

turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait

10 seconds. Make sure the circuit breaker is depressed and then turn the UPS on.

7. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

8. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the

battery every three months to ensure battery life.

FRONT PANEL DESCRIPTION

1 Power On/Off Switch

Press the power switch to turn the UPS ON or OFF.

2 LCD Function Selected Switch

Press the LCD function selected switch to know the UPS status.

REAR PANEL DESCRIPTION

1 AC Inlet

Connect to utility power through the input power cord.

2 Input Circuit Breaker

The Circuit Breaker provides optimal overload protection.

3 AC outlet

The UPS provides 6 outlets for connected equipment to insure temporary uninterrupted operation

during a power failure and against surges and spikes.

4 Serial Port to PC

This port allows connection and communication from the DB9 serial on the computer to the UPS unit.

The UPS communicates its status to the PowerPanel® Personal Edition software.

5 USB Port to PC

This port allows connection and communication from the USB port on the computer to the UPS unit.

The UPS communicates its status to the PowerPanel® Personal Edition software.

NOTE: Only one of these two ports can be used as communication and control of the UPS unit at one time.

6 Communication Protection Ports RJ11/RJ45

Communication protection ports will protect any standard modem, fax, telephone line, or network cable.

IMPORTANT SAFETY INSTRUCTIONS

INSTALLING YOUR UPS SYSTEM

BASIC OPERATION

Model Value 1200E-GP Value 1500E-GP Value 2200E-GP

Capacity (VA) 1200 1500 2200

Capacity (Watts) 720 900 1320

Input

Input Voltage Range 160-265Vac

Frequency Range 47~63Hz (Auto Sensing)

AVR Boost @ 200V

Output

On Battery Output

Voltage Simulated Sine Wave at 230Vac +/-10%

On Battery Output

Frequency 50/60Hz +/-1%

Transfer Time 4ms Typical

Overload Protection On Utility: Circuit Breaker & Internal Current Limiting

On Battery: Internal Current Limiting

Surge Protection

Lightning / Surge

Protection Yes

Operating Temperature 0°C to 40°C

Operating Relative

Humidity 0 to 90% non-condensing

Physical

Total # of UPS outlets (6) IEC 320 C13

Maximum

Dimensions(LxWxH) 326x140x180mm

Weight (kg) 12.7 14.0 15.1

Batterie

Sealed Maintenance

Free Lead Acid Battery 12V / 7Ah p2-x2 12V / 8.5Ah p2-x2 12V / 9Ah p2-x2

Typical Recharge Time 8 hours

User Replaceable Yes

Status Indicators

Indicators Power On / Using Battery

Audible Alarms On Battery, Low Battery, Overload

Communication

PowerPanel® Personal

Edition Software Windows 7/Vista/XP/2000/Server 2003, Linux

Management

Auto-Charger Yes

Auto-Restart Yes

USB Yes

LCD INDICATION

Line mode

UPS Status Display Capacity Display Digital Value Display

Select SW

Press Load

Cap.

Battery

Cap.

Input

Voltage

Output

Voltage

Run

Time

Load

Batt.

Initial V X -- X V X V

1st V X -- X V X V

2nd V X -- X V X V

3rd V X -- X X V V

4th V X -- X V X V

5th(Return) V X -- X V X V

Press >3sec

(Sound Disable) V X V X -- -- -- -- -- -- --

Press >3sec

again

(Sound Enable)

V X X X -- -- -- -- -- -- --

(Overload) V X -- V -- -- -- -- -- -- --

“V” : Illuminated, “X” : Not Illuminated, “--“ : Either

Battery mode

UPS Status Display Capacity Display Digital Value Display

Select SW

Press Load

Cap.

Battery

Cap.

Input

Voltage

Output

Voltage

Run

Time

Load

Batt.

Initial X V -- X X V V

1st X V -- X X V V

2nd X V -- X V X V

3rd X V -- X X V V

4th X V -- X X V V

5th(Return) X V -- X X V V

Press >3sec

(Sound Disable) X V V X -- -- -- -- -- -- --

Press >3sec

again

(Sound Enable) X V X X -- -- -- -- -- -- --

(Overload) X V -- V -- -- -- -- -- -- --

“V” : Illuminated, “X” : Not Illuminated, “--“ : Either

CyberPower’s Green Commitment

CyberPower is dedicated to the development of green products, and has adopted

Green practices throughout its business, including: membership in Climate Savers

Computing Initiative (CSCI), accordance with the Restriction on Hazardous

Substances (RoHS), Waste Electrical and Electronic Equipment (WEEE) protocols,

as well as ISO 14001 and IECQ QC080000. CyberPower pledges to provide the

advanced energy solution for the environment and become a leading eco-friendly

organization in the UPS industry.

Reduce Energy Cost with GreenPower UPSTM Technology

CyberPower’s goal is not only to provide eco-friendly products but also to bring the best value for consumers.

The advanced energy-saving design improves the operating efficiency and eliminates waste energy

consumption. As a result, consumers will enjoy significant energy cost savings with the adoption of

GreenPower UPSTM technology.

Problem Possible Cause Solution

Battery not fully charged.

Recharge the battery by leaving

the UPS plugged in.

The UPS does not perform

expected runtime.

Battery is slightly worn out.

Contact CyberPower Systems

about

replacement batteries at

service@cpsww.com.au

The on/off switch is designed to

prevent damage by rapidly

turning it off and on.

Turn the UPS off. Wait 10

seconds and then turn the UPS

on.

The unit is not connected to an

AC outlet.

The unit must be connected to a

220-240V 50/60Hz outlet.

The battery is worn out.

Contact CyberPower Systems

about

replacement batteries at

service@cpsww.com.au

The UPS will not turn on.

Mechanical problem.

Contact CyberPower Systems at

service@cpsww.com.au

Circuit breaker has tripped due to

an overload.

Turn the UPS off and unplug at

least one piece of equipment.

Wait 10 seconds, reset the circuit

breaker by depressing the

button, and then turn the UPS

on.

Batteries are discharged.

Allow the unit to recharge for at

least 4 hours.

Outlets do not provide power to

equipment.

Unit has been damaged by a

surge or spike.

Contact CyberPower Systems at

service@cpsww.com.au

The serial/USB cable is not

connected.

Connect the serial/USB cable to

the UPS unit and an open serial

port on the back of the

computer. You must use the

cable that came with the unit.

PowerPanel® Personal Edition is

inactive.

The unit is not providing battery

power.

Shutdown your computer and

turn the UPS off. Wait 10

seconds and turn the UPS back

on. This should reset the unit.

Additional troubleshooting information can be found at www.cpsww.com.au

For more information, visit www.cpsww.com.au or contact

CyberPower Systems B.V.

Flight Forum 3545 5657DW Eindhoven The Netherlands

Tel: +31 40 2348170, E-MAIL: sales@cpsww.com.au

part without permission is prohibited. PowerPanel® and PowerPanel® Plus are trademarks of CyberPower

Systems (USA) Inc.

TECHNICAL SPECIFICATIONS CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

TROUBLESHOOTING

Specyfikacje produktu

Marka:	CyberPower
Kategoria:	zasilacz UPS
Model:	Value 1200E
Kolor produktu:	Czarny
Waga produktu:	12700 g
Czas ładowania:	8 h
Technologia baterii:	Ołowiany (VRLA)
Ilość portów Ethernet LAN (RJ-45):	1
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	0 - 95 %
Liczba portów USB 2.0:	1
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-15 - 45 °C
Wymiary produktu (SxGxW):	140 x 326 x 180 mm
Czas odpowiedzi (typowy):	4 ms
System operacyjny:	Windows 98/Me/2000/NT/XP/Vista
Moc rzeczywista:	720 W
Szeregowe porty komunikacyjne:	1
Maksymalna możliwa do konfiguracji moc:	1.2 kVA
Słyszalny alarm:	Tak
Porty modemu rj-11:	1
Wartość nominalna napięcia wyjściowego:	230 V