Instrukcja obsługi CyberPower Smart App Intelligent LCD/AVR

CyberPower zasilacz UPS Smart App Intelligent LCD/AVR

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CyberPower Smart App Intelligent LCD/AVR (2 stron) w kategorii zasilacz UPS. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

OR1500LCDRTXL2U

OR2200LCDRTXL2U

User’s Manual

K01-0000075-00

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.

Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. Ensure the input power is removed

before servicing the batteries. There are no user serviceable parts inside except for the battery.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not

grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a computer

component.

CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in

accordance with the National Electric Code, ANSI/NFPA 70.

CAUTION! The UPS is suitable for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data

Processing Equipment, ANSI/NFPA 75.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical

applications. DO NOT use in any circumstance that would affect operation and safety of life support equipment, medical applications, or patient

care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation

from the aquarium can cause the unit to short out.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit x 1 (b) User’s manual x 1 (c) Rack mount brackets x 2 (d) Stands x 2 (e) Telephone cable x 1

(f) Emergency Power Off cable x 1 (g) PowerPanel

® Business Edition software CD x 1 (h) Serial cable x 2

(i) USB A+B type cable x 1 (j) Warranty registration card x 1

WHAT IS AVR

The OR1500LCDRTXL2U/OR2200LCDRTXL2U provides complete power protection from utility

power that is not always consistent. The OR1500LCDRTXL2U features 1840 Joules of surge

protection and the OR2200LCDRTXL2U features 2060 Joules of surge protection. Both units

provide long lasting battery backup during power outages with maintenance free batteries. The

OR1500LCDRTXL2U/OR2200LCDRTXL2U ensure consistent power to your computer system

and include software that will automatically save your open files and shutdown your computer

system during a utility power loss.

AUTOMATIC VOLTAGE REGULATOR

The OR1500LCDRTXL2U/OR2200LCDRTXL2U stabilizes inconsistent utility power voltage to nominal levels that are safe for equipment.

Inconsistent incoming utility power may be damaging to important data files and hardware, but with Automatic Voltage Regulation (AVR),

damaging voltage levels are corrected to safe levels. AVR automatically increases low utility power and decreases high utility power to a

consistent and safe 110/120 volts. If incoming utility voltage drops below 90 volts, or exceeds 140 volts the units automatically switch to battery

back-up power.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the outlet does not exceed the UPS unit’s rated capacity (1500VA/1125W for OR1500LCDRTXL2U,

2190VA/1650W for OR2200LCDRTXL2U). If the rated capacities of the unit are exceeded, an overload condition may occur and cause the

UPS unit to shut down or the circuit breaker to trip.

2. There are many factors that can affect the amount of power that your computer system will require. It is suggested that the load placed on

the battery outlets not exceed 80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the

battery for at least 8 hours is highly recommended to ensure that the battery’s maximum

charge capacity is achieved. A loss of charge may occur during shipping and

storage. To recharge the battery, simply leave the unit plugged into an AC outlet.

2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other peripherals

requiring battery backup into the battery power supplied outlets. Plug the other peripheral

equipments (printer, scanner, speakers) into the full-time surge protection outlets.

DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other

large electrical devices into the UPS. The power demands of these devices will overload and

possibly damage the unit.

3. To protect a fax, phone or modem, connect a telephone cable or network cable from the wall jack outlet

to the IN jack of the UPS. Connect a telephone cable or network cable from the OUT jack of the UPS to a

fax machine, telephone, modem, or network devices.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, refrigerator, copier, etc…). The warranty prohibits the use of extension cords, outlet strips, and

surge strips.

5. Press the power switch to turn the unit on. The Power On indicator light will illuminate and the unit will “beep”.

If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at

least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and then turn the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store the UPS for an extended period, cover it and store with the battery fully charged. While in storage, recharge the battery every three

months to ensure battery life.

8. To use PowerPanel® Business Edition software, connect the serial cable to the

serial port or the USB port on the UPS and the computer. These OR units include

one serial port, one dry contact, and one USB port to allow connection and

communication between the UPS and computers. Serial port II produces basic

information for equipment that can utilize a dry contact UPS. The primary computer

(with PowerPanel® Business Edition installed) is the computer that you will use to

control the UPS and make changes to the operation of the UPS. When there is a

power failure, the computer connected to the Primary port will start to shut down after

a user controlled delay. PowerPanel

® Business Edition will save and close any open

files prior to shutting down the system.

DESCRIPTION

①

①①

Power Switch

Master on/off switch for equipment connected to the UPS.

②

②②

Power On Indicator (blue)

This LED is illuminated when the utility power is normal and the UPS

outlets are providing power, free of surges and spikes.

③

③③

LCD module display

Crystal Blue intelligent LCD panel shows all the UPS information using

icons and messages. For more information please review the

“Definitions for Illuminated LCD Indicators” section below.

④

④④

LCD function selection switch

The switch can be used to select the LCD display contents including

input/output voltage and estimated run time, etc.

⑤

⑤⑤

8 Full Time Battery Powered and Surge Protected Outlets

The unit has eight battery powered/surge suppression outlets for connected equipments to ensure temporary uninterrupted operation of

your equipment during a power failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum, sump pump or other

large electrical devices into the UPS. The power demands of these devices will overload and possibly damage the unit.)

⑥

⑥⑥

AC Input Power Cord

Heavy-duty, extra long power cord.

⑦

⑦⑦

Output Circuit Breaker

Resettable circuit breakers provide output optimal overload protection.

⑧

⑧⑧

Input Circuit Breaker

Resettable circuit breakers provide input optimal overload protection.

⑨

⑨⑨

USB Port

The USB port allows connection and communication between the USB port on the computer and the UPS unit.

⑩

⑩⑩

Communication Protection Ports

Communication protection ports will protect any standard modem, fax, telephone line, network or Ethernet connection (RJ11/RJ45).

⑪

⑪⑪

Wiring Fault Indicator (red)

This LED indicator will illuminate to warn the user that a wiring problem exists, such as bad ground, missing ground or reversed wiring. If

this is illuminated, disconnect all electrical equipments from the outlet and have an electrician verify the outlet is properly wired. The unit will

not provide surge protection without being plugged into a grounded and properly wired wall outlet.

⑫

⑫⑫

Coax/Cable/DSS Surge Protection

The Coax/Cable/DSS surge protection ports will protect any cable modem, CATV converter, or DSS receiver.

⑬

⑬⑬

Serial Port I (Primary)

The serial port allows connection and communication between the UPS and the computer.

⑭

⑭⑭

Serial Port II (Dry Contact)

Dry contact produces information for equipment that can utilize dry contact signals.

⑮

⑮⑮

EPO (Emergency Power Off) Port:

The interface can be used to switches for emergency power off.

Note: EPO function is provided in UPS. EPO remote switch which is a Push-Back button installed computer room outside by a phone line,

and not connected any other equipment.

⑯

⑯⑯

SNMP/HTTP Network Slot:

Remove the cover panel to install an optional RMCARD provides remote monitoring and management of your UPS over a network.

⑰

⑰⑰

External Battery Pack Connector

Use to connect the optional CyberPower external battery packs for extended runtime.

REPLACING THE BATTERY

Read and follow the IMPORTANT SAFETY INSTRUCTIONS before servicing the battery. Service the battery under the supervision of personnel

knowledgeable of batteries and their precautions. CAUTION! Servicing of the battery should only be performed by trained personnel

familiar with batteries and their precautions. For more information on battery replacement, contact your dealer or call the number on

this manual.

Replacement of batteries located in an OPERATOR ACCESS AREA.

1. When replacing batteries, replace with the same number of the following battery: RBP834 (BP7-12 / BB) for the OR1500LCDRTXL2U, or

a CyberPower qualified 7Ah battery; RBP844 (HR9-12 / BB) for the OR2200LCDRTXL2U, or a CyberPower qualified 9Ah battery.

2. CAUTION! Risk of Energy Hazard, 12 V, maximum 7(BP7-12 for the OR1500LCDRTXL2U) or 9 (HR9-12 for the OR2200LCDRTXL2U)

Ampere-hour battery. Before replacing batteries, remove conductive jewelry such as chains, wrist watches, and rings. High energy

conducted through these materials could cause severe burns;

3. CAUTION! Do not dispose of batteries in a fire. The batteries may explode;

4. CAUTION! Do not open or mutilate batteries. Released material is harmful to the skin and eyes. It may be toxic.

CAUTION - RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BATTERIES ACCORDING

TO LOCAL REGULATIONS.

BATTERY REPLACEMENT PROCEDURE:

REMINDER: Batteries are considered HAZARDOUS WASTE and must be disposed of properly. Most retailers that sell lead-acid batteries

collect used batteries for recycling, as required by local regulations.

1. INPUT voltage meter: This meter measures the AC voltage that the UPS system is

receiving from the utility wall outlet. The UPS is designed, through the use of automatic

voltage regulation, to continuously correct output voltage to connected equipment to a

safe 110/120 voltage output range. In the event of a complete power loss, severe brownout,

or over-voltage, the UPS relies on its internal battery to supply consistent 110/120 output

voltage. The INPUT voltage meter can be used as a diagnostic tool to identify

poor-quality input power.

2. OUTPUT voltage meter: This meter measures, in real time, the AC voltage that the

UPS system is providing to the computer, such as normal line mode, AVR mode, and

battery backup mode.

(Note: The OUTPUT voltage meter shows the status of the battery backup outlets.)

3. ESTIMATED RUN TIME: This displays the run time estimate of the UPS with current battery capacity and load.

4. NORMAL icon: This icon appears when the UPS is working under normal conditions.

5. BATTERY icon: During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps followed by a pause) to

indicate the UPS is operating from its internal batteries. During a prolonged brownout or blackout, the alarm will beep rapidly every 1/2

second (and the BATT.CAPACITY meter shows one 20% capacity segment shaded) to indicate the UPS’s batteries are nearly out of power.

You should save files and turn off your equipment immediately.

6. AVR (Automatic Voltage Regulation) icon: This icon appears whenever your UPS is automatically correcting low AC line voltage

without using battery power. This is a normal, automatic operation of your UPS, and no action is required on your part.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY WARNINGS

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

1. Remove the right side front panel. 2. Remove the three retaining screws of the cable 3. Remove the two retaining screws of

protection cover then remove the cover. the cable connectors.

4. Disconnect the black and red cable. 5. Remove the four retaining screws. 6. Insert the new battery pack. Assemble the

screws, cover, cable and front panel in the

reverse sequence of above steps.

Recharge the unit for 4-8 hours to ensure

the UPS

erforms ex

ected runtime.

7. SILENT MODE icon: This icon appears whenever the UPS is in silent mode. The buzzer does not beep during silent mode until the

battery reaches low capacity.

8. OVER LOAD icon: This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To clear the

overload, unplug some of your equipment from the battery-supplied outlets until the icon turns off and the alarm stops.

9. FAULT icon: This icon appears if there is a problem with the UPS, Contact CyberPower Systems at tech@cyberpowersystems.com for

further help and support.

10. BATT. CAPACITY meter: This meter displays the approximate charge level (in 20% increments) of the UPS’s internal battery. During a

blackout or severe brownout, the UPS switches to battery power, the BATTERY icon appears, and the charge level decreases.

11. LOAD CAPACITY meter: This meter displays the approximate output load level (in 20% increments) of the UPS battery outlets.

Alarm

CONDITION

On Off Off Off Normal

Off On Off Beeps twice

every 30 seconds

Utility Failure - The UPS is providing power to battery

power-supplied outlets from its battery.

Off On Off Rapid Beeping

every 1/2 second

Utility Failure - The UPS is providing battery power. Rapid

beeping indicates the unit will run out of power shortly.

Off On On Constant tone

Battery Overload - Occurs when connected equipment

exceeds the listed capacity of the UPS. Turn the UPS off,

unplug at least one piece of equipment from battery outlets,

wait 10 seconds, reset the circuit breaker and turn the unit on.

Problem Possible Cause Solution

Full-time surge protection outlets

stop providing power to

equipment. Circuit breaker

button is projecting from the side

of the unit.

Circuit breaker has tripped due to an

overload.

Turn the UPS off and unplug at least one piece of

equipment. Wait 10 seconds, reset the circuit breaker by

depressing the button, and then turn the UPS on.

Battery not fully charged. Recharge the battery by leaving the UPS plugged in.

The UPS does not perform

expected runtime. Battery is worn out. Contact CyberPower Systems about replacement batteries

at tech@cyberpowersystems.com

The on/off switch is designed to

prevent damage from rapidly turning

it off and on.

Turn the UPS off. Wait 10 seconds and then turn the UPS

on.

The unit is not connected to an AC

outlet. The unit must be connected to a 110/120V 60Hz outlet.

The battery is worn out. Contact CyberPower Systems about replacement batteries

at tech@cyberpowersystems.com

The UPS will not turn on.

Mechanical problem. Contact CyberPower Systems at

tech@cyberpowersystems.com

The USB / serial cable is not

connected.

Connect the USB / serial cable to the UPS unit and an open

USB / serial port on the back of the computer. You must

use the cable that came with the unit.

The USB / serial cable is connected

to the wrong port.

Check the back of the computer for an additional USB /

serial port. Move the cable to this port.

The unit is not providing battery

power.

Shutdown your computer and turn the UPS off. Wait 10

seconds and turn the UPS back on. This should reset the

unit.

PowerPanel® Business Edition is

inactive (all icons are gray).

The serial cable is not the cable that

came with the unit.

Please use the serial cable that came with the unit for the

software.

Additional troubleshooting information can be found under “Support” at

www.CPSww.com

Model OR1500LCDRTXL2U OR2200LCDRTXL2U

Capacity 1500VA / 1125W 2190VA / 1650W

Input Voltage on Utility 90V to 140V

Input Frequency 47 Hz to 63 Hz

On-Battery Output Voltage 120Vac ± 5%

Transfer Time 4ms Typical

Max. Load for UPS Outlets (8 Outlets) 1500VA / 1125W 2190VA / 1650W

Max. Load for Full-Time Surge Protection outlets

(8 Outlets) 12 Amps 17.2 Amps

On-Battery Output Wave Form Simulated Sine Wave

Operating Temperature + 32°F to 104° F / 0° C to 40° C

Operating Relative Humidity 0 to 90% non-condensing

Size (L x W x H) 433 x 478 x 88 mm (2U Rack)

17” x 18.8” x 3.5”

Net Weight 59.5lbs / 27kg 66.1lbs / 30kg

Battery Type 12V, 7Ah (BP7-12 / BB) 12V, 9Ah (HR9-12 / BB)

Typical Battery Recharge Time 8 hours from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Recommended Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778, CSA C22.2 No 107.3, FCC/DoC Class B

SYSTEM FUNCTIONAL BLOCK DIAGRAM

Advanced Energy-Saving Patented Bypass Technology

CyberPower’s patented GreenPower UPS™ with Bypass Technology reduces UPS energy

costs by up to 75% compared to conventional UPS models. Even when utility power is normal,

conventional UPS models constantly pass power through a transformer. By contrast, under

normal conditions the advanced circuitry of a GreenPower UPS™ bypasses the transformer.

As a result, the power efficiency is significantly increased while decreasing waste heat, using less

energy, and reducing energy costs.

When an abnormal power condition occurs, the GreenPower UPS™ automatically runs power

through its transformer to regulate voltage and provide “safe” power. Since utility power is

normal over 88% of the time, the GreenPower UPS™ operates primarily in its efficient bypass mode.

The GreenPower UPS™ is also manufactured in accordance with the Restriction on Hazardous Substances (RoHS) directive making

it one of the most environmentally-friendly on the market today.

Read the following terms and conditions carefully before using the CyberPower OR1500LCDRTXL2U / OR2200LCDRTXL2U (the

“Product”). By using the Product you consent to be bound by and become a party to the terms and conditions of this Limited Warranty

and Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and conditions of this

Warranty, you should return the Product for a full refund prior to using it.

Who is Providing this Warranty?

CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.

What Does This Warranty Cover?

This warranty covers defects in materials and workmanship in the Product under normal use and conditions. It also covers

equipment that was connected to the Product and damaged because of the failure of the Product.

What is the Period of Coverage?

This warranty covers the Product for three years and connected equipment for as long as you own the Product.

Who Is Covered?

This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.

How Do You Get Service?

1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12

th Ave. E., STE 400, Shakopee, MN 55379

or send us an e-mail message at claims@cyberpowersystems.com for instructions.

2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have

information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and

Request a Claim Number.

3. You must provide a dated Proof-of-Purchase receipt (or other proof of the original purchase) and provide a description of the

defect.

4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the

damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the

shipping label or include it with the product. You must prepay all shipping costs, you are responsible for packaging and

shipment, and you must pay the cost of the repair estimate.

How Long Do I Have To Make A Claim?

All claims must be made within ten days of the occurrence.

What Will We Do To Correct Problems?

CyberPower will inspect and examine the Product.

If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if

CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund

to you the full purchase price you paid for the Product (purchase receipt showing price paid is required).

If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the

connected equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you

the fair market value (NOT REPLACEMENT COST) of the equipment at of the time of the damage. We will use Orion Blue Book, or

another a third-party valuation guide, or eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to

$300,000 for the OR1500LCDRTXL2U and OR2200LCDRTXL2U.

Who Pays For Shipping?

We pay when we send items to you; you pay when you send items to us.

What Are Some Things This Warranty Does Not Cover?

1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any

data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software.

2. This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product

or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or

maintenance, or use with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums,

medical or life support devices, etc.

What are the Limitations?

The sole and exclusive remedies of the Initial Customer are those provided by this Warranty.

1. This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired

and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use

of any adapters or other connectors.

2. The Product must have been plugged directly into the power source and the equipment connected to the Product must be

directly connected to the Product and not “daisy-chained” together in serial fashion with any extension cords, another Product

or device similar to the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty.

3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in

conformance with any license, instruction manual, or warnings provided with the Product and the equipment connected to it.

4. The Product must have been used at all times within the limitations on the Product’s VA capacity.

Where Can I Get More Information?

For further information please feel free to contact CyberPower at Cyber Power Systems (USA), Inc. 4241 12

th Ave E., STE 400,

Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at claims@cyberpowersystems.com.

DEFINITIONS FOR LCD ICONS & AUDIBLE INDICATION

TECHNICAL SPECIFICATIONS

Limited Warranty and Connected Equipment Guarantee

TROUBLESHOOTING

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

EMI

Filter

Surge

Suppressor

AVR

Charge

AC/DC

Battery

Inverter

Input Output

Normal Mode

Battery Mode

Specyfikacje produktu

Marka:	CyberPower
Kategoria:	zasilacz UPS
Model:	Smart App Intelligent LCD/AVR
Kolor produktu:	Czarny
Typ wyświetlacza:	LCD
Wysokość produktu:	88.9 mm
Szerokość produktu:	431.8 mm
Głębokość produktu:	477.52 mm
Waga produktu:	26988.7 g
Długość kabla:	3 m
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Czas ładowania:	8 h
Certyfikaty:	UL1778, cUL 107.3, FCC DOC Class B
Technologia baterii:	Ołowiany (VRLA)
Zakres temperatur (eksploatacja):	0 - 35 °C
Zakres wilgotności względnej:	0 - 90 %
Funkcje zarządzania:	SNMP, HTTP
Układ:	Rackmount/Tower
Liczba portów USB 2.0:	1
Rodzaj baterii:	12V, 7AH
Częstotliwość danych wejściowych:	- Hz
Diody LED:	Tak
Port RS-232:	2
Czas odpowiedzi (typowy):	4 ms
Moc rzeczywista:	1125 W
Pojemność stelaża:	2U
Maksymalna możliwa do konfiguracji moc:	1.5 kVA
Wartość znamionowa udaru energii:	1840 J
Słyszalny alarm:	Tak
Ilość gniazd sieciowych:	8 x gniazdo sieciowe
Typy wyjść AC:	NEMA 5–15R
Porty modemu rj-11:	2
Typowy czas podtrzymania przy połowie obciążenia:	18 min
Typowy czas podtrzymania przy pełnym obciążeniu:	7 min
Wartość nominalna napięcia wyjściowego:	120 V
Wartość nominalna napięcia wejściowego:	90-140 V
Funkcje ochrony zasilania:	Przeładowanie
Filtr EMI/RFI:	Tak
Akumulatory wymieniane podczas pracy:	Tak