Instrukcja obsługi CyberPower EC850LCD

CyberPower zasilacz UPS EC850LCD

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla CyberPower EC850LCD (2 stron) w kategorii zasilacz UPS. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/2

EC350G / EC550G / EC750G

EC650LCD / EC850LCD

User’s Manual

K01-0000277-00

Thank you for purchasing a CyberPower product. Please take a few minutes to register your product at www.cpsww.com/registration.

Registration certifies your product's warranty, confirms your ownership in the event of a product loss or theft and entitles you to free technical

support.

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.

Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is disconnected.

CAUTION! The UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not

grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electric shock, turn off the unit and unplug it from the AC power source before installing a computer component.

CAUTION! Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/Data Processing Equipment,

ANSI/NFPA 75.

CAUTION! To reduce the risk of fire, connect only to a circuit provided with 20 amperes maximum branch circuit over current protection in

accordance with the National Electric Code, ANSI/NFPA 70.

CAUTION! Risk of explosion if battery is replaced by an incorrect type. Batteries shall be installed by service personnel, and the replacement of

batteries with a suitable recommended type. Dispose of used batteries according to the instructions.

CAUTION! Do not dispose of batteries in a fire. The batteries may explode.

CAUTION! Do not open or mutilate batteries. Released electrolyte is harmful to the skin and eyes. It may be toxic.

DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does not sell products for life support or medical

applications. use in any circumstance that would affect operation and safety of life support equipment, any medical applications or DO NOT

patient care.

DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire or electric shock, do not use with or near an aquarium. Condensation

from the aquarium can cause the unit to short out.

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

(a) UPS unit (b) User’s manual (c) USB device cable

*PowerPanel® Personal Edition software is available on our website. Please visit www.cpsww.com and go to the Software Section for

free download.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Ensure that the equipment plugged into the UPS does not exceed the UPS unit’s rated capacity (350VA/255W for EC350G, 550VA/330W for

EC550G, 750VA/450W for EC750G, 650VA/390W for EC650LCD, and 850VA/510W for EC850LCD). If the rated capacities of the unit are

exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to trip.

2. There are many factors that can affect the amount of power that your electronic equipment will require. For optimal system performance

keep the load below 80% of the unit’s rated capacity.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, after receiving a new UPS, to

ensure the battery’s maximum charge capacity, it is recommended that you charge the battery

for at least 8 hours. Your UPS is equipped with an auto-charge feature. When the UPS is

plugged into an AC outlet, the battery will automatically charge when it’s turned on or turned off.

2. With the UPS unit turned off and unplugged, connect your computer, monitor, and any other

peripherals requiring battery backup from the SURGE/BATTERY outlets. Plug the other peripheral equipment (e.g. printer, scanner,

speakers, etc.) into the full-time surge protection outlets. DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum

cleaner, sump pump, or other large electrical device into the “Battery and Surge Protected Outlets”. The power demands of these

devices will overload and possibly damage the unit.

3. To protect a fax, phone, or modem line, connect a telephone cable from the wall jack outlet to the IN jack of the UPS.

Connect a telephone cable from the UPS OUT jack to protect a modem port on the computer, a telephone, or fax machine.

4. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g. air

conditioner, refrigerator, copier, etc.). The warranty prohibits the use of extension cords, outlet strips,

and surge strips in conjunction with the UPS unit.

5. Press the power switch to turn the unit on. The Power On indicator light will illuminate green and the unit will “beep” twice.

6. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at

least one piece of equipment from the battery power supplied outlets. Make sure the circuit breaker is depressed and then turn the UPS on.

7. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

8. To store the UPS for an extended period of time, cover it and store with the battery fully charged. While in storage, recharge the battery

every three months to ensure optimal battery life.

9. Ensure the wall outlet and UPS are located near the equipment being attached for proper accessibility.

DESCRIPTION

1. Battery and Surge Protected Outlets

The unit has battery powered/surge suppression outlets to ensure temporary uninterrupted operation of your equipment during a power

failure. (DO NOT plug a laser printer, paper shredder, copier, space heater, vacuum cleaner, sump pump, or other large electrical

device into the “Battery and Surge Protected Outlets.” The power demands of these devices will overload and possibly damage

the unit.)

2. Full-Time Surge Protection Outlets / ECO Controlled Outlets

The unit has surge suppression outlets to provide surge and line noise protection. Three of the surge-only outlets are also ECO controlled

outlets.

3. Power Switch

To turn the UPS , press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after a ON

short beep.

To turn the UPS OFF, press the power button for approximately 2 seconds - you will hear a constant tone (1 second) - and release after two

short beeps.

Alarm setting: The audible alarm can be turned by quickly pressing the POWER button twice. The default setting is for the Alarm Off or On

On. To turn the Alarm Off, quickly press the power button twice. You will hear two short beeps when the Alarm is turned Off. To turn the

Alarm back On, quickly press the power button twice. You will hear a single short beep when the Alarm is turned On. *When the Alarm is

turned Off, there will be no audible notification when the UPS reaches a low battery state.

4. Power On Indicator (green)

This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of surges and spikes.

5. Mode Switch (EC650LCD and EC850LCD only)

Press the Mode Switch for approximately 3 seconds to enter setup mode to select four functions: Utility High Voltage Range, Utility Low

Voltage Range, ECO ON/OFF, and LCD sleep ON/OFF. When a function is selected, press Mode Switch for 3 seconds to view options.

When an option is selected, wait for 8 seconds for the setting to be confirmed. After the setting has been confirmed the LCD screen will

leave setup mode and go back to status display. If there is no action for 8 seconds during setup, the LCD will also leave setup mode and go

back to the status display.

a. Utility High Voltage Range: Adjust the value of high voltage range.

b. Utility Low Voltage Range: Adjust the value of low voltage range.

c. ECO: Eon/EoF (ON/OFF): Turn on or turn off ECO function. For more information, refer to section. ECO Function Setup

d. LCD: L1/L0 (ON/OFF):

* When LCD is set to L1, LCD will be always ON. When LCD is set to L0, LCD will dim if untouched for 1 minute.

* In battery mode, LCD is always on regardless if the setting is L1 or L0.

ECO Button (EC350G, EC550G, and EC750G only)

Press ECO button for 3 seconds to turn on or turn off ECO function in line mode.

6. ECO Indicator

ECO Indicator shows the condition of ECO function. For more information, refer to section. ECO Function Setup

7. Communication Protection Ports

Communication protection ports will protect any standard modem, fax, or telephone line. (RJ11)

8. Circuit Breaker

Located on the side of the UPS, the circuit breaker serves to provide overload and fault protection.

9. USB Port to PC

The USB port allows connection and communication between the USB port on the computer and the UPS unit. The UPS communicates its

status to the PowerPanel® Personal Edition software. The USB port is also used for operating the UPS in ECO mode. For more information,

refer to section. ECO Function Setup

10. Outlets Designed for AC Adapters

The UPS unit has 4 widely-spaced outlets so AC power adapters can be plugged into the UPS without overlapping or blocking adjacent

outlets.

ECO FUNCTION SETUP

ECO Function

When the ECO function is active the UPS can detect whether the PC that is connected to the USB port is turned on or off. If the PC is turned

off, the UPS will turn off the ECO controlled outlets and cut power to the devices connected to them in order to save power. Generally, these

are peripherals that are not used when the PC is not turned on.

ECO Controlled Outlets

Three of the surge-only outlets are also ECO controlled outlets. When the PC that is connected to the USB port is turned off, the UPS will

turn off the ECO controlled outlets to save energy.

ECO Setup

1. The factory default setting is OFF. ECO mode can only be enabled/disabled and will only be active when the UPS is receiving utility

power and not in battery mode.

2. For the EC650/850LCD, press the Mode switch for approximately 3 seconds to enter setup mode and select the ECO function. When

the ECO function is selected, press the Mode switch for 3 seconds to turn the function ON or OFF. Once ON or OFF is selected, wait 8

seconds for the setting to be confirmed and the LCD screen will return to status mode. For the EC350/550/750G, press the ECO button

for 3 seconds to turn ON or OFF the ECO function.

3. When the ECO function is OFF, utility power from the ECO outlets will always be on. When the ECO function is ON, utility power from

the ECO outlets will turn off if the PC connected to the UPS via the USB port is turned off or if there is no PC is connected to the UPS via

USB.

ECO Indicator

The LED will be blinking when the ECO function is turned ON but the PC is either off or not connected. The LED will be solid if the ECO

function is turned on and the connected PC is on. The LED is off when the ECO function is disabled. See below table for more information.

ECO Indicator ECO Function ECO Outlet Status Condition

Solid (green) ON With Utility Power When PC is ON and USB port on the UPS is connected, Peripherals

will receive power to operate.

Blinking ON Without Utility Power When PC is OFF or the USB port on the UPS is not connected, power

to the Peripherals will be turned off.

OFF OFF Always with Utility

Power

When PC is ON/OFF, Peripherals is always ON.

DEFINITIONS FOR ILLUMINATED LED INDICATORS

Power ON

Alarm

CONDITION

On Off Normal

On Beep twice

every 30 seconds

Utility Failure- The UPS is providing power to battery power-supplied

outlets from its battery.

On Rapid Beeping

every 1/2 second

Utility Failure- The UPS is providing battery power. Rapid beeping

indicates the unit will run out of power shortly.

Off Constant tone

Battery Overload - Occurs when connected equipment exceeds the

listed capacity of the UPS. Turn the UPS off, unplug at least one

piece of equipment from battery outlets, wait 10 seconds, reset the

circuit breaker and turn the unit on.

INPUT voltage meter: This meter measures the AC voltage that the UPS system is receiving from the

utility wall outlet. The UPS is designed to continuously supply connected equipment with stable output

voltage. In the event of a complete power loss, severe brownout, or over-voltage, the UPS relies on its

internal battery to supply consistent 110/120 output voltage. The INPUT voltage meter can be used as

a diagnostic tool to identify poor-quality input power.

OUTPUT voltage meter: This meter measures, in real time, the AC voltage that the UPS system is

providing to the computer during normal AC/Utility Power mode, and battery backup mode.

ESTIMATE RUN TIME: This displays the run time estimate of the UPS with the current battery

capacity and load.

NORMAL icon: This icon appears when the UPS is working under normal conditions.

BATTERY icon: During a severe brownout or blackout, this icon appears and an alarm sounds (two short beeps followed by a pause) to indicate

the UPS is operating from its internal battery. The alarm will continue to sound during a prolonged brownout or blackout. The BATT.CAPACITY

meter will show one 20% capacity segment remaining to indicate the UPS's battery is nearly out of power. You should save files and turn off your

equipment immediately.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY WARNINGS

DEFINITIONS FOR ILLUMINATED LCD INDICATORS

The LCD display indicates a variety

of UPS operational conditions. All

descriptions apply when the UPS is

plugged into an AC outlet and turned

on or when the UPS is on battery.

PRODUCT REGISTRATION

EC650LCD (8 outlets)

EC850LCD

(12

outlets)

EC350G / EC550G (8 outlets)

EC750G

(12 outlets)

OVER LOAD icon: This icon appears and an alarm sounds to indicate the battery-supplied outlets are overloaded. To clear the overload, unplug

some of your equipment from the battery-supplied outlets until the icon turns off and the alarm stops.

BATT. CAPACITY meter: This meter displays the approximate charge level of the UPS's internal battery in 20% increments. During a blackout

or severe brownout, the UPS switches to battery power (the BATTERY icon appears) and the battery charge level decreases.

LOAD CAPACITY meter : This meter displays the approximate output load level of the UPS battery outlets in 20% increments.

Problem Possible Cause Solution

Full-time surge protection outlets

stop providing power to

equipment. Circuit breaker

button is projecting from the side

of the unit.

Circuit breaker has been tripped due

to an overload.

Turn the UPS off and unplug at least one piece of

equipment. Wait 10 seconds, reset the circuit breaker by

pressing the button, and then turn the UPS on.

The UPS does not perform

expected runtime.

Battery not fully charged. Recharge the battery by leaving the UPS plugged in.

Battery is worn out. Contact CyberPower Systems about replacement batteries

at tech@cpsww.com.

The UPS will not turn on.

The on/off switch is designed to

prevent damage from rapidly turning

it off and on.

Turn the UPS off. Wait 10 seconds and then turn the UPS

on.

The unit is not connected to an AC

outlet. The unit must be connected to a 110/120V 50/60Hz outlet.

The battery is worn out. Contact CyberPower Systems about replacement batteries

at tech@cpsww.com.

Mechanical problem. Contact CyberPower Systems at tech@cpsww.com

The frequency is outside of the

operating range of 47-63Hz.

Turn the UPS off. Make sure the frequency range is within

47-63Hz. Or you can turn the UPS on in battery mode.

PowerPanel® Personal Edition is

inactive (all icons are gray).

The USB cable is not connected. Connect the USB cable to the UPS unit and an open USB

port on the computer.

The USB cable is connected to a

bad USB port. Check for a different USB port and plug the cable in.

The unit is not providing battery

power.

Shutdown your computer and turn the UPS off. Wait 10

seconds and turn the UPS back on. This should reset the

unit.

Additional troubleshooting information can be found at “Support” at

www.CPSww.com

Model

EC350G

EC550G

EC750G

EC650LCD

EC850LCD

Capacity 350VA/255W 550VA/330W 750VA/450W 650VA/390W 850VA/510W

Nominal Input

Voltage

120Vac

Input Frequency 47 Hz to 63 Hz

On-Battery Output

Voltage

120Vac ± 5%

On-Battery Output

Frequency

50Hz/60Hz ± 1% (auto-sensing)

Max. Load for UPS

Outlets

350VA/255W 550VA/330W 750VA/450W 650VA/390W 850VA/510W

Max. Load for

Full-Time Surge

Protection outlets

10 Amps

On-Battery Output

Wave Form

Simulated Sine Wave

Operating

Temperature

32°F to 104° F / 0° C to 40° C

Operating Relative

Humidity

0 to 90% non-condensing

Size (W x H x D) 5.9” x 3.1” x 10.6”

150 x 79 x 269 mm

5.9” x 3.1” x 10.6”

150 x 79 x 269 mm

7” x 3.1” x 12.2”

178 x 79 x 310 mm

5.9” x 3.1” x 10.6”

150 x 79 x 269 mm

7” x 3.1” x 12.2”

178 x 79 x 310mm

Net Weight 4.5 lbs / 2.1kg 6.0 lbs / 2.7kg 7.7 lbs / 3.5kg 6.4 lbs / 2.9kg 7.7 lbs / 3.5kg

Typical Battery

Recharge Time

8 hours typical from total discharge

Typical Battery Life 3 to 6 years, depending on number of discharge/recharge cycles

Battery Sealed Maintenance Free Lead Acid Battery

Safety Approvals UL1778(UPS), cUL CSA C22.2 No.107.3-05, FCC/DoC Class B

SYSTEM FUNCTION BLOCK DIAGRAM

EMI Filter

Surge

Suppressor

Charger

AC/DC Battery

Inverter

Input Output

Normal Mode

Battery Mode

Advanced Energy-Saving Design

The GreenPower UPS™ has a high-efficiency charger, which makes it the most energy-efficient UPS in

its class. The advanced high-frequency charging system significantly improves charging efficiency and

conserves energy. As a result of this advanced design, the GreenPower UPS™ uses less energy

compared to competitive models. The GreenPower UPS™ is manufactured in accordance with the

Restriction on Hazardous Substances (RoHS) directive making it one of the most

environmentally-friendly UPS on the market today.

Read the following terms and conditions carefully before using the CyberPower EC350G, EC550G, EC750G, EC650LCD, and

EC850LCD (the “Product”). By using the Product you consent to be bound by and become a party to the terms and conditions of this

Limited Warranty and Connected Equipment Guarantee (together referred to as this “Warranty”). If you do not agree to the terms and

conditions of this Warranty, you should return the Product for a full refund prior to using it.

Who is Providing this Warranty?

CyberPower Systems (USA), Inc. (“CyberPower”) provides this Limited Warranty.

What Does This Warranty Cover?

This warranty covers defects in materials and workmanship in the Product under normal use and conditions.

It also covers equipment that was connected to the Product and damaged because of the failure of the Product.

What is the Period of Coverage?

This warranty covers the Product for three years. Connected equipment is covered for as long as you own the Product.

Who Is Covered?

This warranty only covers the original purchaser. Coverage ends if you sell or otherwise transfer the Product.

How Do You Get Service?

1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN 55379

or send us an e-mail message at claims@cpsww.com for instructions.

2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have

information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and

Request a Claim Number.

3. You must provide a dated Proof-of-Purchase receipt (or other proof of the original purchase) and provide a description of the

defect.

How Do You Open A Connected Equipment Claim?

1. Call us at (877) 297-6937 or write to us at Cyber Power Systems (USA), Inc., 4241 12th Ave. E., STE 400, Shakopee, MN

55379, or send us an e-mail message at claims@cpsww.com for instructions, within 10 days of the occurrence.

2. When you contact CyberPower, identify the Product, the Purchase Date, and the item(s) of Connected Equipment. Have

information on all applicable insurance or other resources of recovery/payment that are available to the Initial Customer and

Request a Claim Number.

3. You must provide a dated purchase receipt (or other proof of the original purchase) and provide a description of the damage to

your connected equipment.

4. Pack and ship the product to CyberPower and, if requested, the item(s) of Connected Equipment, a repair cost estimate for the

damage to the Connected Equipment, and all claim forms that CyberPower provides to you. Show the Claim Number on the

shipping label or include it with the product. You must prepay all shipping costs, you are responsible for packaging and

shipment, and you must pay the cost of the repair estimate.

How Long Do I Have To Make A Claim?

All claims must be made within ten days of the occurrence.

What Will We Do To Correct Problems?

CyberPower will inspect and examine the Product.

If the Product is defective in material or workmanship, CyberPower will repair or replace it at CyberPower's expense, or, if

CyberPower is unable to or decides not to repair or replace the Product (if defective) within a reasonable time, CyberPower will refund

you the full purchase price you paid for the Product (purchase receipt showing price paid is required).

If it appears that our Product failed to protect any equipment plugged into it, we will also send you forms for making your claim for the

connected equipment. We will repair or replace the equipment that was damaged because of the failure of our Product or pay you

the fair market value (NOT REPLACEMENT COST) of the equipment at the time of the damage. We will use Orion Blue Book, or

another third-party valuation guide, or eBay, craigslist, or other source to establish that amount. Our maximum liability is limited to

$100,000 for the EC350G, EC550G, EC750G, EC650LCD, and EC850LCD.

Who Pays For Shipping?

We pay when we send items to you; you pay when you send items to us.

What isn’t covered by the warranty?

1. This Warranty does not cover any software that was damaged or needs to be replaced due to the failure of the Product or any

data that is lost as a result of the failure or the restoration of data or records, or the reinstallation of software.

2. This Warranty does not cover or apply to: misuse, modification, operation or storage outside environmental limits of the Product

or the equipment connected to it, nor for damage while in transit or in storage, nor if there has been improper operation or

maintenance, or use with items not designed or intended for use with the Product, such as laser printers, appliances, aquariums,

medical or life support devices, etc.

What are the Limitations?

The sole and exclusive remedies to the Initial Customer are those provided by this Warranty.

1. This Warranty does not apply unless the Product and the equipment that was connected to it were connected to properly wired

and grounded outlets (including compliance with electrical and safety codes of the most current electrical code), without the use

of any adapters or other connectors.

2. The Product must have been plugged directly into the power source and the equipment connected to the Product must be

directly connected to the Product and not “daisy-chained” together in serial fashion with any extension cords, another Product

or device similar to the Product, surge suppressor, or power tap. Any such installation voids the Limited Warranty.

3. The Product and equipment connected to it must have been used properly in a suitable and proper environment and in

conformance with any license, instruction manual, or warnings provided with the Product and the equipment connected to it.

4. The Product must have been used at all times within the limitations on the Product’s VA/Watt capacity.

The Product was designed to eliminate disrupting and damaging effects of momentary (less than 1ms) voltage spikes or impulses

from lightning or other power transients. If it can be shown that a voltage spike lasting longer than 1ms has occurred, the occurrence

will be deemed outside the rated capabilities of the Product and the Limited Warranty is void. CyberPower Does Not Cover or

Undertake Any Liability in Any Event for Any of the Following:

1. Loss of or damage to data, records, or software or the restoration of data or records, or the reinstallation of software.

2. Damage from causes other than AC Power Line Transients, spikes, or surges on properly installed, grounded and

code-compliant 120 volt power lines in the United States and Canada; transients, surges or spikes on standard telephone land

lines, PBX telephone equipment lines or Base 10T Ethernet lines, when properly installed and connected. (This exclusion

applies, for example, to fluctuations in data transmission or reception, by CATV or RF transmission or fluctuations, or by

transients in such transmission.)

3. Damage from any circumstance described as excluded above with respect to the Product.

4. Damages from fire, flood, wind, rain, rising water, leakage or breakage of plumbing, abuse, misuse or alteration of either the

product or the Connected Equipment.

5. CyberPower excludes any liability for personal injury under the Limited Warranty and Connected Equipment Guarantee.

CyberPower excludes any liability for direct, indirect, special, incidental or consequential damages, whether for damage to or

loss of property [EXCEPT FOR (AND ONLY FOR) the specific limited agreement of CyberPower to provide certain warranty

benefits regarding "Connected Equipment" under this Warranty], loss of profits, business interruption, or loss of information or

data. NOTE: Some States or Provinces do not allow the exclusion or limitation of incidental or consequential damages, so the

above limitation may not apply to you.

6. The Product is not for use in high-risk activities or with aquariums. The Product is not designed or intended for use in hazardous

environments requiring fail-safe performance, or for use in any circumstance in which the failure of the Product could lead

directly to death, personal injury, or severe physical or property damage, or that would affect operation or safety of any medical

or life support device (collectively, "High Risk Activities"). CyberPower expressly disclaims any express or implied warranty of

fitness for High Risk Activities or with aquariums. CyberPower does not authorize use of any Product in any High Risk Activities

or with Aquariums. . ANY SUCH USE IS IMPROPER AND IS A MISUSE OF THE PRODUCT

The application of the United Nations Convention of Contracts for the International Sale of Goods is expressly excluded. CyberPower

is the warrantor under this Limited Warranty.

Where Can I Get More Information?

For further information please feel free to contact CyberPower at Cyber Power Systems (USA), Inc. 4241 12th Ave E., STE 400,

Shakopee, MN 55379; call us at (877) 297-6937; or send us an e-mail message at claims@cpsww.com.

CyberPower Systems encourages environmentally sound methods for disposal and recycling of its UPS products.

Please dispose and/or recycle your UPS and batteries in accordance to the local regulations of your state.

TECHNICAL SPECIFICATIONS

Limited Warranty and Connected Equipment Guarantee

TROUBLESHOOTING

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

Specyfikacje produktu

Marka:	CyberPower
Kategoria:	zasilacz UPS
Model:	EC850LCD
Kolor produktu:	Czarny
Typ wyświetlacza:	LCD
Wysokość produktu:	78.74 mm
Szerokość produktu:	309.88 mm
Głębokość produktu:	177.8 mm
Waga produktu:	3492.66 g
Długość kabla:	1.5 m
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS, ENERGY STAR
Czas ładowania:	8 h
Certyfikaty:	UL1778, cUL 107.3, FCC
Napięcie operacyjne wejścia (maksymalne):	140 V
Technologia baterii:	Ołowiany (VRLA)
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	0 - 90 %
Układ:	Kompaktowy
Liczba portów USB 2.0:	1
Waga wraz z opakowaniem:	3538.02 g
Częstotliwość danych wejściowych:	47/63 Hz
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-15 - 45 °C
Dopuszczalna wilgotność względna:	0 - 95 %
Dołączone oprogramowanie:	PowerPanel
Wymiary opakowania (SxGxW):	381 x 241.3 x 109.22 mm
Dopuszczalna wysokość podczas eksploatacji (n.p.m.):	0 - 3000 m
Napięcie baterii:	12 V
Moc rzeczywista:	510 W
Maksymalna możliwa do konfiguracji moc:	0.85 kVA
Napięcie operacyjne wejścia (minimalne):	96 V
Napięcie operacyjne wyjścia (maksymalne):	- V
Napięcie operacyjne wyjścia (minimalne):	- V
Wartość znamionowa udaru energii:	526 J
Funkcje ochrony przed przepięciami:	Modem, Telephone
Słyszalny alarm:	Tak
Ilość gniazd sieciowych:	12 x gniazdo sieciowe
Typy wyjść AC:	NEMA 5–15R
Porty modemu rj-11:	2
Typowy czas podtrzymania przy połowie obciążenia:	10.4 min
Typowy czas podtrzymania przy pełnym obciążeniu:	2.15 min
Dopuszczalna wysokość (n.p.m.):	0 - 15000 m
Wartość nominalna napięcia wyjściowego:	120 V
Funkcje ochrony zasilania:	Przeładowanie
Wtyczka:	NEMA 5-15P
Ochrona przed nagłym wzrostem napięcia:	Tak
Przebieg falowy:	Sinus
Topologia UPS:	Technologia line-interactive
Filtr EMI/RFI:	Tak