Instrukcja obsługi Cramer A82TXPS

Cramer Niesklasyfikowane A82TXPS

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cramer A82TXPS (71 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/71
cramer.eu
2903286 (Pole saw)
EN | DE | ES | IT | FR | PT | NL | RU| FI | SV | NO| DA| PL | CS | SK | SL| HR|
EL | AR| TR | LT | LV | ET |
2cramer.eu
EN
1 Pole saw head
2 Chain cover lock nut
3 Oil tank
4 Bar
5 Chain
6 Scabbard
7 Knob
8 Release button
9 Cutters
10 Cutters chain rotation
11 Drive links
12 Bar groove
13 Chain adjustment screw
Product Overview
Your machine has been engineered and manufactured to high standard for
dependability, ease of operation, and operator safety. When properly cared for, it
will give you years of trouble-free performance.
Know your pole saw head
Assembly
Insatll the pole saw head (see ) Figure 2
1 Remove the rubber protector.
2 Loosen the knob on the coupler.
3 Push in the release button located on the lower shaft. Align the release
button with the positioning hole and slide the two shafts together. Rotate
the lower shaft until the button locks into the positioning hole.
4 Tighten the knob securely.
Operation
Adding bar and chain lubricant (see ) Figure 3
Use Bar and Chain Lubricant. It is designed for chains and chain oilers, and is
formulated to perform over a wide temperature range with no dilution required.
NOTE: Pole saw comes from the factory with no bar and chain lubricant added.
Level should also be checked after every 20 minutes of use and refilled as needed.
1 Unscrew and remove the cap from the oil tank.
2 Pour oil in the tank and monitor the level on the indicator.
3 Make sure no impurities penetrate the oil tank when filling.
4 Screw on the oil cap and tighten it.
NOTE: Do not use dirty, used or otherwise contaminated oils. Damage may occur
to the bar or chain.
NOTE: It is normal for oil to seep from the saw when not in use. To prevent
seepage, empty the oil tank after each use then run for one minute. When storing
the unit for a long period of time (three months or longer) be sure the chain is
lightly lubricated; this will prevent rust on the chain and bar sprocket.
Preparation for cutting
•Wear non-slip gloves for maximum grip and protection.
•Maintain a proper grip on the unit whenever the motor is running. Use your
right hand to firmly grip the rear handle while your left hand has a firm grip
on the pole shaft.
•Hold unit firmly with both hands. Always keep your left hand on the pole
shaft and your right hand on the rear handle, so your body is to the left of
the chain line. Never use a left-handed (cross-handed) grip, or any stance
that places your body or arm across the chain line.
•Never stand directly under the limb you are cutting.
•Be certain the collars are fully tightened before operating equipment; check
them periodically for tightness during use to avoid serious injury.
Work techniques
Delimbing a tree (see ) Figure 4
3
cramer.eu
EN
WARNING!
Make sure there is nothing or nobody in the area where the
branches will fall.
•Stand opposite the branch you want to cut.
•Start cutting lower branches followed by the higher ones.
•Cut downwards to prevent the bar from getting jammed.
Limbing tree branches (see ) Figure 5
Limbing means removing the branches from a felled tree.
WARNING!
Be careful of where the branches are lying on the ground, the risk of
them being under tension, the direction the branch may go during
cutting and the risk of the tree being unstable after the branch has
been cut.
When limbing, it is necessary to leave the lower, larger branches to support the
trunk on the ground. Remove the small branches with a single cut.
It is recommended to cut the tensioned branches working from the bottom
upwards to prevent the pole saw from bending.
MAINTENANCE
Adjusting the chain tension (see Figure 6.10.11)
•Untighten the chain cover lock nut slightly by turning it counterclockwise.
You do not need to remove the chain cover in order to adjust the chain
tension.
•Rotate the chain adjustment screw clockwise to increase the chain tension
and rotate counterclockwise to decrease the chain tension.
•Once the chain is at the desired tension, tighten the chain cover lock nut.
WARNING!
During normal saw operation, the temperature of the chain
increases. The drive links of a correctly tensioned warm chain will
hang approximately 1/16 in. (1,58 mm) out of the bar groove.
WARNING!
New chains tend to stretch; check the chain tension frequently
and tension as required.
Assemble the bar and chain (see Figure 6-11)
•Loose the lock nut and remove the chain cover.
•The bar contains a bar stud slot that fits over the bar stud. The bar also
contains a chain tension pin hole which fits over the chain tensioning pin.
•Place the bar onto the bar stud so that the chain tensioning pin fits into the
chain tensioning pin hole.
•Fit the chain over the sprocket and into the bar groove. The cutters on the
top of the bar should face toward the bar tip, in the direction of the chain
rotation.
•Replace the chain cover.
•Remove all slack from chain by turning the chain tensioning screw
clockwise, assuring that the chain seats into the bar groove during
tensioning.
•Lift the tip of the bar up to check for sag. Release the tip of the bar, and
turn the chain tensioning screw 1/2 turn clockwise. Repeat this process
until sag does not exist.
•Hold the lip of the bar up and tighten the lock nut securely.
•Chain is correctly tensioned when there is no slack on the underside of the
bar, the chain is snug, but it can be turned by hand without binding.
•Tighten the lock nut.
NOTE: If the chain is too tight, it will not rotate. Loosen the chain cover lock nut
slightly and turn the chain adjustment screw 1/4 turn counterclockwise. Lift the
tip of the guide bar up and retighten the chain cover lock nut. Ensure that the
chain will rotate without binding.

Specyfikacje produktu

Marka: Cramer
Kategoria: Niesklasyfikowane
Model: A82TXPS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Cramer A82TXPS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Cramer

Cramer

Cramer A82TXT Instrukcja

4 Października 2024
Cramer

Cramer 48SK192 Instrukcja

4 Października 2024
Cramer

Cramer A82TXHD Instrukcja

4 Października 2024
Cramer

Cramer A82TXPS Instrukcja

4 Października 2024
Cramer

Cramer 48SK96 Instrukcja

4 Października 2024
Cramer

Cramer A82TXE Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024