Instrukcja obsługi Cramer A82TXHD

Cramer Niesklasyfikowane A82TXHD

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Cramer A82TXHD (48 stron) w kategorii Niesklasyfikowane. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/48
cramer.eu
2902986 (Hedge trimmer)
EN | DE | ES | IT | FR | PT | NL | RU| FI | SV | NO| DA| PL | CS | SK | SL| HR| EL|
AR | TR | LT | LV | ET |
2cramer.eu
EN
Product Overview
Your machine has been engineered and manufactured to high standard for
dependability, ease of operation, and operator safety. When properly cared for, it
will give you years of trouble-free performance.
Know your Pole Hedge Trimmer Head
1. Blade
2. Pivot Button
3. Scabard
4. Auxiliary handle
5. Rubber protector
6. Lower shaft
7. Release button
8. knob
Assembly
•This product requires assembly.
•Carefully remove the product and any accessories from the box. Make sure
that all items listed in the packing list are included.
•Inspect the product carefully to make sure no breakage or damage
occurred during shipping.
•Do not discard the packing material until you have carefully inspected and
satisfactorily operated the product.
Install the Pole Hedge Trimmer Head (See Figure 2)
1 Remove the rubber protector.
2 Loosen the knob on the coupler.
3 Push in the release button located on the lower shaft. Align the release
button with the positioning hole and slide the two shafts together. Rotate the
lower shaft until the button locks into the positioning hole.
4 Tighten the knob securely.
NOTE: If the button does not release completely in the positioning hole, the
shafts are not locked into place. Slightly rotate from side to side until the button is
locked into place.
Adjust the Trimmer Head Angle (See figure 3)
The trimmer head pivots 180° and can be locked into 13 positions within that range.
1 Hold the auxiliary handle.
2 Pull back and hold the pivot button.
3 Use the auxiliary handle to adjust the trimmer head angle.
4 Release the pivot button once the trimmer head is in the desired position.
5 The trimmer head should lock securely in place.
Operation
Tips for Optimum Use (See figure 4-5)
•Start by trimming the top of the hedge. Slightly tilt the tool (up to 15° relative
to the line of cut) so that the blade tips point slightly towards the hedge. This
will cause the blades to cut more effectively. Hold the tool at the desired
angle and move it steadily along the line of cut. The doublesided blade allows
you to cut in either direction.
•In order to obtain a very straight cut, stretch a piece of string along the length
of the hedge at the desired height. Use the string as a guideline, cutting just
above it.
•In order to obtain flat sides, cut upwards with the growth. Younger stems
move outwards when the blade cuts downwards, causing shallow patches
in the hedge.
•Take care to avoid any foreign objects. Especially avoid hard objects such as
metal wire and railings, as these could damage the blades.
•Regularly oil the blades.
Maintenance
Clean the Machine
Clean the machine thoroughly to remove all dust and debris, after every work session.
•To reduce fire hazards, keep the machine and, in particular, the motor free
of leaves, branches or excessive grease.
•Always clean the machine after use with a damp cloth dipped in neutral
detergent.
•Remove all traces of humidity using a soft damp cloth. Humidity can
generate risks of electric shocks.
3
cramer.eu
EN
•Do not use aggressive detergents or solvents to clean the plastic parts or
handgrips.
•Do not spray water onto the motor and electrical components and prevent
them from getting wet.
•To avoid overheating and damage to the motor or the battery, always keep
the cooling air vents clean and free of debris.
Clean and Lubrication of the Cutting Means
To increase the efficiency and working life of the blades, clean and lubricate them
carefully after each work session:
•Place the machine in a stable horizontal position on the ground.
•Use a soft cloth to clean the blades, along with a brush to remove more
difficult dirt and debris.
•Lubricate the blades by applying a light layer of specific oil, preferably the
non-pollutant type, along the upper edge of the blade.
•Keep all nuts, bolts and screws tight to be sure the equipment is in safe
working condition.
•Check regularly that the handles are fixed firmly.
Troubleshooting
PROBLEM PROBABLE
CAUSE POSSIBLE SOLUTION
With the safety
lock button and
trigger on, the
cutting means
does not turn.
The machine is
damaged.
Do not use the machine. Immediately turn
off the machine remove the battery and
Contact a Service Centre.
The cutting means
overheats whilst
working.
Insufcient
blade
lubrication.
Turn off the machine, wait until the cutting
means is stationary, remove the battery
and lubricate the blades.
Excessive noise
and/or vibration is
experienced whilst
working.
Loose or
damaged parts.
Turn off the machine, remove the battery
and:
– inspect for damage;
– check for and tighten any loose parts;
– have any damaged parts replaced or
repaired with parts having equivalent
specications.
The machine gives
off smoke whilst
working.
The machine is
damaged.
Do not use the machine. Immediately turn
off the machine remove the battery and
Contact a Authorised Service Centre.
Technical Data
PROPERTY VALUE
Cutting length 466 mm

Specyfikacje produktu

Marka: Cramer
Kategoria: Niesklasyfikowane
Model: A82TXHD

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Cramer A82TXHD, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Niesklasyfikowane Cramer

Cramer

Cramer A82TXT Instrukcja

4 Października 2024
Cramer

Cramer 48SK192 Instrukcja

4 Października 2024
Cramer

Cramer A82TXHD Instrukcja

4 Października 2024
Cramer

Cramer A82TXPS Instrukcja

4 Października 2024
Cramer

Cramer 48SK96 Instrukcja

4 Października 2024
Cramer

Cramer A82TXE Instrukcja

4 Października 2024

Instrukcje Niesklasyfikowane

Najnowsze instrukcje dla Niesklasyfikowane

Black Diamond

Black Diamond BD1121530000ALL1 Instrukcja

15 Października 2024
Husqvarna

Husqvarna K 970 SmartGuard Instrukcja

15 Października 2024
Stihl

Stihl HT 70 Instrukcja

15 Października 2024
Ernesto

Ernesto H14270 Instrukcja

15 Października 2024
Uniden

Uniden BT MIC KIT Instrukcja

15 Października 2024
Vaude

Vaude Omnis Bike 26 Instrukcja

15 Października 2024
ART

ART ProChannel II Instrukcja

15 Października 2024
Aukey

Aukey DR02J Instrukcja

15 Października 2024
Master Lock

Master Lock 653EURD Instrukcja

15 Października 2024
Roland

Roland FR-18 Diatonic Instrukcja

15 Października 2024