Instrukcja obsługi Chord Anni

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Chord Anni (7 stron) w kategorii Receiver. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
Operation 3.0
Chord Electronics
Anni | Manual
_
Chord Electronics
Product Communication | English
_
The Pumphouse Farleigh Lane,
East Farleigh, Maidstone
ME16 9NB United Kingdon
info@chordelectronics.co.uk
chordelectronics.co.uk
Anni
Manual
_
V.1
Power output 10 W 8 ohms
THD 0.02 %
Signal to noise -92 dB
Noise floor -110 dB
Frequency response 5 Hz-60 kHz
chordelectronics.co.uk
_
Gain
Anni benefits from a two-stage (high and low) gain function on the
loudspeaker outputs (only) to suit a wide range of partnering speakers.
Press the gain button to alternate between low (blue) and high (red) gain
modes, allowing 3 seconds to switch between modes.
When using either of the headphone outputs, Anni is automatically
switched to low gain mode. If when inserting headphones Anni was
previously set to high gain (red) the gain sphere will show purple, before
reverting back to red when the headphones are removed. If low gain (blue)
was previously selected, the gain sphere will remain blue and continue to
display blue when the headphones are disconnected.
If using Anni with Qutest, ensure Qutests output voltage is set no higher
than 2 V. The Qutest manual describes how to set output voltage.
Placement
Anni benefits from extensive casework ventilation and a cooling fan for
demanding environments. Always ensure Anni is used in a well-ventilated
setting, away from direct sunlight and heat sources, and has sucient
space around the unit.
Chord Electronics’ Qutest Stand System (available separately) has been
designed to perfectly house Anni. Otherwise, care should be taken not to
stack other units on Anni.
Support
If you need support, in the first instance, please contact your supplying
retailer who will be best placed to assist you. If you need additional help
beyond that of your retailer, please visit our support page: chordelectronics.
co.uk/get-support
Specifications
Inputs 2.1
Connect to any line level source component using a standard RCA cable.
Rear
Front
Introduction
Anni is a next-generation desktop integrated amplier that complements the
high quality of our multi-award-winning Qutest DAC and Huei phono stage. We
took a dierent approach to the design and created a powerful, desktop device
for headphones and desktop loudspeakers that belies its compact dimensions.
Accurately controlled across the entire audio bandwidth with extraordinary
low frequency capability, Annis protection circuitry allows for the delivery of
enormous peak current outputs for its size whilst avoiding overdrive; it does this
dierently to other ampliers on a half-cycle by half-cycle basis. If the output
of the amp is being over-driven, Anni will detect it and collapse the waveform
on each over-driven, half-cycle. So not clipping like other ampliers but instead
going from a completely undistorted waveform to one that is missing half-cycles
i.e. it becomes heavily distorted suddenly until the level is slightly reduced. Then
the music signal will totally recover without any harm occurring to the amplifier
or speaker, with the music being once again undistorted.
Power on/o 3.1
With connections successfully made (as per section 2.0), and volume set to
zero, press the power button. The button will display green, before settling
on cyan. Pressing the power button again puts the unit in standby; the
button will display red.
Note: if either of the headphone outputs are connected, the power button
will display green to show the speaker output has been disconnected. If the
headphones are then removed, the power button will revert to cyan and the
speaker output will become active.
Select an input 3.2
Select input 1 or 2 by pushing the volume knob sequentially. Input 1 is
indicated by a blue LED ring, input 2 is red.
Amplifier operation 3.3
With connections successfully made and with volume set to zero, select the
input, press play on the chosen source and adjust Anni’s volume accordingly.
Connections and
controls
Operation
2.0 3.0
6.35 mm (1/4 inch)
headphone output
Volume control/input
select
3.5 mm headphone output
12 V DC output
Speaker output left
channel
Speaker output right
channel
Line level inputs 1 and 215 V DC power input
General operation and
important information
1.0
Chord Electronics
Anni | Manual
_
Connecting to loudspeakers 2.2
Connect to the loudspeaker using 4 mm banana-plug-terminated speaker
cable, observing polarity.
Ground terminal
Gain
button
Power
button
Connecting to headphones 2.3
Using the front two outputs, connect headphones with 6.35 mm (1/4-
inch) or 3.5 mm terminations to Anni and the output will automatically be
selected. The volume controls both headphone outputs simultaneously: they
are not independently controllable.
Headphone operation 3.4
Anni has both 6.35 mm (1/4 inch) and 3.5 mm headphone outputs, which
can be used both individually or simultaneously meaning two can listen.
With the volume set to zero, connect to one or both headphone outputs and
slowly increase the volume.
Note: if connecting headphones when music is already playing through
the loudspeakers, a short delay will be experienced before the headphone
output becomes active (to protect the amp). In addition, low gain will be
automatically selected. Removing the headphones (with speakers still
connected) will revert the output signal back to the speakers.
Input 1 Input 2
Right speaker
channel
Left speaker
channel
6.35 mm
headphone
3.5 mm
headphone
Input 1 Input 2
Power connection
Anni is supplied with an external power supply and has been designed to
be permanently connected to a power source. Connect the included 15 V supply
to Anni. If hum occurs, use the ground terminal to connect to an available
earth point. Always set the volume to zero before playback and before
connecting/removing headphones.
Connections and controls 2.0

Specyfikacje produktu

Marka: Chord
Kategoria: Receiver
Model: Anni

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Chord Anni, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Receiver Chord

Chord

Chord Anni Instrukcja

14 Października 2024
Chord

Chord 2yu Instrukcja

2 Września 2024
Chord

Chord Dave Instrukcja

27 Sierpnia 2024
Chord

Chord Mezzo 75 Instrukcja

18 Sierpnia 2024
Chord

Chord Qutest Instrukcja

16 Sierpnia 2024
Chord

Chord Ultima 2 Instrukcja

9 Sierpnia 2024
Chord

Chord Dual Instrukcja

5 Lipca 2024

Instrukcje Receiver

Najnowsze instrukcje dla Receiver

Apart

Apart SBR160 Instrukcja

14 Października 2024
American Audio

American Audio VLP 600 Instrukcja

14 Października 2024
Sennheiser

Sennheiser EM 9046 SU Instrukcja

14 Października 2024
Yamaha

Yamaha MusicCast RX-V481 Instrukcja

13 Października 2024
JL Audio

JL Audio VX600/6i Instrukcja

12 Października 2024
Pioneer

Pioneer SX-303RDS Instrukcja

10 Października 2024
Denon

Denon AVR-991 Instrukcja

10 Października 2024
Denon

Denon AVR-4810 Instrukcja

10 Października 2024
Avantree

Avantree Audiplex Instrukcja

9 Października 2024
Avantree

Avantree Oasis Plus Instrukcja

9 Października 2024