Instrukcja obsługi Casio DQ-950S

Casio zegar DQ-950S

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Casio DQ-950S (4 stron) w kategorii zegar. Ta instrukcja była pomocna dla 13 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
Operation Guide DQ-950S
1
MA1205-EA
ILLUSTRATION
©
2012 CASIO COMPUTER CO., LTD.
SNOOZE/LIGHT
ALARM
SET DEMO
RESET
SNOOZE
ON
OFF
3
4
2
ALARM
SNOOZE
ON
OFF
8
SET DEMO
5 6 7
1
MAX/MIN
MAX/MIN
RESET
SNOOZE/LIGHT
RESET
A sticker is affixed to the glass of the clock when you purchase it. Be sure to remove the sticker before using the
clock.
Depending on the clock model, the configuration of your clock may differ somewhat from that shown in the
illustration.
Current time
(Hour, minutes,
seconds)
Day of the week
Current Humidity Current Temperature
DATE
(month - date)
PM
indicator
Alarm time
Snooze on
indicator
Alarm on
indicator
Alarm Off Snooze Alarm On
Operation Guide DQ-950S
2
GENERAL GUIDE
11
11
1SNOOZE/LIGHT button
Press this button to illuminate the display for about five seconds.
The SNOOZE/LIGHT button is the area at the top of the clock panel marked “SNOOZE/LIGHT”.
Pressing this button while the alarm is sounding stops the alarm.
22
22
2MAX/MIN button
Press this button to display the high and low temperature and humidity values.
33
33
3°C/°F button
Press this button to toggle the temperature units between Celsius and Fahrenheit.
44
44
4+ (UP) / (DOWN) buttons
Use these buttons to change the alarm time or the setting that is flashing on the display.
55
55
5SET button
Use this button when setting the current time.
66
66
6DEMO button
Press this button to test the alarm sound.
77
77
7RESET button
Press this button to reset the clock after replacing its batteries.
88
88
8Alarm Mode selector
SNOOZE: Snooze alarm on
ON: Alarm on
OFF: Alarm off
USING THE CLOCK
1. Press the SET button (5) to cycle through the setting screens as shown below.
12-hour/24-hour
Setting Screen
Time Setting ScreenMonth and Day Setting Screen
Year Setting Screen
Normal Timekeeping Screen Contrast Setting Screen
2. While the screen you want is displayed, use the (DOWN) and + (UP) buttons (4) to change the flashing digits.
MAX/MIN
Press (DOWN
)
to decrease
the flashing digits.
Press + (UP) to increase
the flashing digits.
Holding down + (UP) or (DOWN) changes the flashing digits at high speed.
You can set the year in the range of 2000 to 2099. The day of the week is set automatically in accordance with
the date setting.
Pressing + (UP) or (DOWN) while the Time Setting Screen is on the display causes the seconds count to be
reset to 00.
Each press of + (UP) or (DOWN) while the 12-hour/24-hour Setting Screen is on the display toggles
between 12-hour and 24-hour timekeeping.
You can set the contrast level in the range of 1 to 10.
3. After making the settings you want, use the SET button (5) to display the Normal Timekeeping Screen.
The clock automatically returns to the Normal Timekeeping Screen if you leave a setting screen on the display
for about three minutes without performing any operation.
Operation Guide DQ-950S
3
USING THE ALARM
The alarm sounds when the alarm time you set is reached. You can also use the Alarm Mode selector (8) to
select the snooze alarm feature.
Setting the Alarm Time
Use the (DOWN) and + (UP) buttons (4) to set the alarm time.
Pressing the (DOWN) and + (UP) buttons (4) causes the alarm time to appear in place of the date on the
display.
MAX/MIN
Press to change the alarm
time setting (+).
Press to change the alarm
time setting (
).
Holding down + (UP) or (DOWN) changes the digits at high speed.
Turning the Alarm On and Off
Use the Alarm Mode selector (8) on the side of the clock to turn the alarm on and off, and to select the snooze
feature.
The alarm time appears in place of the date on the display whenever the Alarm Mode selector (8) is set to ON
or SNOOZE.
The volume of the alarm sound cycles through five levels as it sounds.
Stopping the Alarm
When alarm is sounding, press the SNOOZE/LIGHT button (1) to stop it. When the snooze feature is turned on,
the alarm will sound again in about five minutes.
To turn off the snooze feature, slide the Alarm Mode selector (8) to OFF.
USING THE LIGHT
Pressing the SNOOZE/LIGHT button (1) turns on the light and illuminates the display for easy reading in the dark.
Important!
Overuse of the light can shorten battery life.
THERMOMETER AND HYGROMETER FUNCTIONS
A built-in sensor measures temperature and humidity, and shows the measured value on the display.
The readout from the temperature sensor can also be switched between Celsius (°C) and Fahrenheit (°F).
Temperature Measurements
The temperature display shows “LO” for temperatures below –19.9°C (–3.8°F) and “HI” for temperatures above
49.9°C (121.8°F).
Though temperature readings are displayed up to 0°C (32°F) and greater than 41°C (105°F), note that such
readings are actually outside the guaranteed temperature range of this clock.
Switching between Celsius and Fahrenheit
Push the °C/°F button (3) to select either Celsius (°C) or Fahrenheit (°F).
Switching between Celsius and Fahrenheit causes current high temperature/humidity and low temperature/
humidity memory contents to be cleared.
°C/°F button (3)
°C°F
Celsius (°C) Fahrenheit (°F)
Humidity Measurements
The humidity display shows “LO” for humidity below 10% and “HI” for humidity above 90%.
Whenever the current temperature is outside the range of 0°C to 49.9°C, the humidity display will show “– –”.
Daily High Temperature/Humidity, Low Temperature/Humidity Memory
The clock remembers the highest and lowest temperature and humidity readings for the current 24-hour day.
Each press of the MAX/MIN button (2) cycles between screens as illustrated below.
Daily high and low temperature/humidity memory contents are cleared each day at midnight.
Changing the Temperature/Humidity Display Screen
Press of the MAX/MIN button (2). Each press cycles between screens as shown below.
MAX/MIN button (2)
MAX/MIN button (2)
MAX/MIN button (2)
Current temperature and humidity
High temperature and humidity Low temperature and humidity
Turning On Temperature/Humidity Screen Auto Cycling
Hold down the MAX/MIN button (2) for about one second. This will turn on temperature/humidity screen auto
cycling, which causes the screen contents to cycle from one screen to the next at regular intervals.
Current temperature and humidity
High temperature and humidity Low temperature and humidity
To turn off temperature/humidity screen auto cycling, press the MAX/MIN button (2).
Alarm Mode selector
SNOOZE
ON
OFF
Description
The alarm sounds at the preset time for one minute, and seven more times every five
minutes thereafter. Even if you stop the alarm by pressing the SNOOZE/LIGHT
button (1), the alarm sounds again about five minutes later.
The indicator flashes on the display to indicate that the snooze feature is
activated.
The alarm sounds at the preset time for one minute.
The alarm does not sound.


Specyfikacje produktu

Marka: Casio
Kategoria: zegar
Model: DQ-950S

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Casio DQ-950S, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje zegar Casio

Instrukcje zegar

Najnowsze instrukcje dla zegar