Instrukcja obsługi Bushnell RXS250


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bushnell RXS250 (9 stron) w kategorii Lornetka. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/9
Model #: RXS250 10-21
RED DOT SIGHT OWNERS GUIDE
Thank you for purchasing your new Bushnell® RXS-250 Red Dot Reex Sight (illuminated optical sight).
This manual will help you optimize your viewing experience by explaining how to utilize the sights features
and how to care for it. Read the instructions carefully before using your sight.
WARNING! : DO NOT LOOK AT THE SUN THROUGH THE OPTICS, AS PERMANENT EYE DAMAGE OR EVEN
BLINDNESS MAY RESULT.
Included:
A. Protective Cover Shroud
B. Battery Door & W/E Adjustment Tool
C. CR2032 Lithium Battery (in separate polybag)
D. Bushnell Multi-Tool
E. Weaver Style Low-prole Mounting Base
F. Spudz Cleaning Cloth
A
B
C
D
E
F
3
ABOUT THE BUSHNELL® RXS-250 RED DOT REFLEX SIGHT
The RXS-250 is a state-of-the-art reex sight, designed for hunting, plinking and target shooting with pistols, ries, and shotguns. It may
be directly mounted to compatible pistol slides (or accessory mounts) with the Leupold DeltaPoint® footprint or it may be mounted
to accessory rails using the included low-prole Weaver style mount. It features a battery life of more than 50,000 hours (at a typical
brightness level of “5”)*, a 12-hour auto-timeout feature to prolong battery life (timer countdown resets if any button is pressed, or it may
be disabled for full manual control), battery access without unmounting, and a 4 MOA dot with 10 brightness settings. The sight has an
IP67 rating for water resistance.
*Note: battery life in use will vary depending on the brightness settings used, freshness and quality of the battery, ambient temperature,
and other factors.
Your sight’s illuminated reticle has been pre-focused so the aiming point always appears in focus on the target. Bycomparison, open sights
force you to choose to focus your eye on only the rear sight, front sight or target-or settle for a blurry compromise.
Your sight can be easily used with both eyes open (eye relief is unlimited), increasing the shooter’s awareness of the surrounding
environment and providing faster target acquisition due to the limited parallax design, as the dot follows the movement of the users eye
while remaining xed on the target. Engineered for greater speed and accuracy, the sight allows you to focus on the target rather than a
reticle, thus increasing accuracy. The Bushnell RXS-250 sights electronic illuminated dot has been pre-focused to be parallax free at 50
yards. Parallax error is minimized, from close range up to 100 yds.
MOUNTING YOUR RXS-250™ SIGHT
WARNING! : BEFORE MOUNTING YOUR SIGHT, REPLACING ITS BATTERY, OR REMOVING OR PERFORMING
MAINTENANCE ON THE SIGHT, BE SURE ACTION IS OPEN, CLIP OR MAGAZINE IS REMOVED AND A ROUND
IS NOT IN THE CHAMBER. DO NOT ATTEMPT ANY WORK UNTIL THE FIREARM HAS BEEN CLEARED AND
DETERMINED TO BE SAFE.
WARNING: IF THE SIGHT IS NOT MOUNTED FAR ENOUGH FORWARD, ITS REARWARD MOTION MAY
INJURE THE SHOOTER WHEN THE FIREARM RECOILS.
Your new sight, even with its technologically advanced design and features, will not perform at its best if not properly mounted. One of
the most important contributing factors to the accuracy of your firearm and sight combination is the quality of the mount and care taken
during its installation. The RXS-250 will t all bases compatible with Leupold® DeltaPoint® Pro sights. It also includes a low-prole mount
for mounting on Weaver or Picatinny style accessory rails. Make sure the base you use is manufactured specically for your pistol, rie or
shotgun. Be sure the base is properly installed and securely fastened according to the manufacturers instructions for your safety.
The included hold-down mounting screws (2) are intended to be used with indirect mounting adapter plates like what is utilized for GLOCK
M.O.S. There are other types of optics-ready plate systems from pistol manufacturers (e.g. TAURUS™ TORO) that utilize a pass-through plate
system, which requires the user to utilize screws provided from the pistol manufacturer. If this is the case, additional care must be taken
to ensure the red dot sight is adequately clamped. Some screws may bottom out into the slide and seem to be tight, but in fact are not
adequately clamping the sight onto the slide. The potential resulting looseness can cause lens fracture and potential risk to the user. Always
follow user-manual guidance and/or seek assistance from the respective manufacturers or a qualied gunsmith. Always wear approved eye-
protection.
The base should create a uniform horizontal and vertical mounting platform. Be sure they are properly installed and securely fastened
according to the manufacturer’s instructions for your safety. There is no set eye relief for your RXS-250 sight; therefore, you should provide
at least three inches of clearance between the rear of the sight and your eye when in the shooting position. While 1X power/magnication
sights have unlimited eye-relief, always ensure there is an adequate amount of space between your face and the optic to account for rearm
recoil.
If mounting directly to an adapter plate (common for optics ready pistols), follow the manufacturer’s instructions for attaching the adapter
plate. Unless otherwise specied by the 3rd party manufacturer, be sure to remove any clearance by gently forward loading the plate during
fastening. When attaching the red dot sight to the adapter plate, gently forward load the sight body while fastening. This both removes
clearances that may otherwise shift under recoil and improves the chances of repeatable mounting should the red dot sight need to be
removed for any reason such as maintenance.
If using the included mount, loosen the socket head T15 Torx screw on the mount of the sight using the provided tool, so that the locking
bar can clamp around the rail. Position the mount on your base rail so that the cross-bolt engages a slot. Forward load the mount, so that
the cross-bolt engages the forward face of the chosen mounting slot and clearance is removed. Tighten the T15 Torx bolt. CAUTION: Do
not overtighten. Torque should be set to 15 lb *in f (pound-force inch) for the two sight-to-base screws and 25 lb *in for the mount cross-bolt.f
Remember, not all sights or scopes are compatible with all firearm bases. If there is any doubt in your mind, you should seek the advice
of your local retailer or gunsmith.
Leupold® and DeltaPoint® are registered trademarks of Leupold & Stevens, Inc.
GLOCK® and M.O.S.® are registered trademarks of GLOCK, Inc.


Specyfikacje produktu

Marka: Bushnell
Kategoria: Lornetka
Model: RXS250

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bushnell RXS250, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Lornetka Bushnell

Instrukcje Lornetka

Najnowsze instrukcje dla Lornetka

Pentax

Pentax 7x20 DCF Instrukcja

15 Października 2024
Auriol

Auriol Z31117 Instrukcja

12 Października 2024
Armasight

Armasight 8x36 Instrukcja

10 Października 2024
Kodak

Kodak BCS400 Instrukcja

9 Października 2024
Kodak

Kodak BCS600 Instrukcja

9 Października 2024
Steiner

Steiner M1050 LRF Instrukcja

8 Października 2024
Steiner

Steiner HX 10x42 Instrukcja

8 Października 2024