Instrukcja obsługi Bushnell RXS100


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Bushnell RXS100 (9 stron) w kategorii Lornetka. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/9
Model #: RXS100 10-21
RED DOT SIGHT OWNERS GUIDE
Thank you for purchasing your new Bushnell® RXS-100 Red Dot Reex Sight (illuminated optical sight).
This manual will help you optimize your viewing experience by explaining how to utilize the sights features and how to care
for it. Read the instructions carefully before using your sight.
WARNING! : DO NOT LOOK AT THE SUN THROUGH THE OPTICS, AS PERMANENT EYE DAMAGE OR EVEN
BLINDNESS MAY RESULT.
Included:
A. Battery Door Tool
B. W/E Adjustment Tool
C. 3mm Hex Wrench for Mounting Screws
D. CR2032 Lithium Battery
E. Weaver Style Low-prole Mounting Base
F. Microber Cleaning Cloth
G. Protective Shroud Cover
A
B
C
E
F
G
D
3
Leupold® and DeltaPoint® are registered trademarks of Leupold & Stevens, Inc.
GLOCK® and M.O.S.® are registered trademarks of GLOCK, Inc.
ABOUT THE BUSHNELL® RXS-100 RED DOT REFLEX SIGHT
The RXS-100 is a state-of-the-art reex sight, designed for hunting, plinking and target shooting with pistols, ries, and
shotguns. It may be directly mounted to compatible pistol slides (or accessory mounts) with the Leupold DeltaPoint® footprint
or it may be mounted to accessory rails using the included low-prole Weaver style mount. It features a battery life of more
than 5,000 hours (at a typical brightness level of “3”)*, a 1-hour auto-timeout feature to prolong battery life (timer countdown
resets if any button is pressed), battery access without unmounting, and a 4 MOA dot with 8 brightness settings.
*Note: battery life in use will vary depending on the brightness settings used, freshness and quality of the battery, ambient
temperature, and other factors.
Your sights illuminated reticle has been pre-focused so the aiming point always appears in focus on the target. Bycomparison,
open sights force you to choose to focus your eye on only the rear sight, front sight or target-or settle for a blurry compromise.
Your sight can be easily used with both eyes open (eye relief is unlimited), increasing the shooters awareness of the
surrounding environment and providing faster target acquisition due to the limited parallax design, as the dot follows the
movement of the user’s eye while remaining xed on the target. Engineered for greater speed and accuracy, the sight allows
you to focus on the target rather than a reticle, thus increasing accuracy. The Bushnell RXS-100 sight’s electronic illuminated
dot has been pre-focused to be parallax free at 50 yards. Parallax error is minimized, from close range up to 100 yds.
MOUNTING YOUR RXS-100™ SIGHT
WARNING! : BEFORE MOUNTING YOUR SIGHT, REPLACING ITS BATTERY, OR REMOVING OR PERFORMING
MAINTENANCE ON THE SIGHT, BE SURE ACTION IS OPEN, CLIP OR MAGAZINE IS REMOVED AND A ROUND
IS NOT IN THE CHAMBER. DO NOT ATTEMPT ANY WORK UNTIL THE FIREARM HAS BEEN CLEARED AND
DETERMINED TO BE SAFE.
WARNING: IF THE SIGHT IS NOT MOUNTED FAR ENOUGH FORWARD, ITS REARWARD MOTION MAY
INJURE THE SHOOTER WHEN THE RECOILS.FIREARM
Your new sight, even with its technologically advanced design and features, will not perform at its best if not properly mounted. One
of the most important contributing factors to the accuracy of your firearm and sight combination is the quality of the mount and care
taken during its installation. The RXS-100 will t all bases compatible with Leupold® DeltaPoint® Pro sights*. It also includes a low-
prole base for mounting on Weaver or Picatinny style accessory rails. Make sure the base you use is manufactured specically for
your pistol, rie or shotgun. Be sure the base is properly installed and securely fastened according to the manufacturers instructions
for your safety.
The included hold-down mounting screws (2) are intended to be used with indirect mounting adapter plates like what is utilized for
GLOCK M.O.S.** There are other types of optics-ready plate systems from pistol manufacturers (e.g. TAURUS™ TORO) that utilize a
pass-through plate system, which requires the user to utilize screws provided from the pistol manufacturer. If this is the case, additional
care must be taken to ensure the red dot sight is adequately clamped. Some screws may bottom out into the slide and seem to be tight,
but in fact are not adequately clamping the sight onto the slide. The potential resulting looseness can cause lens fracture and potential
risk to the user. Always follow user-manual guidance and/or seek assistance from the respective manufacturers or a qualied gunsmith.
Always wear approved eye-protection.
The base should create a uniform horizontal and vertical mounting platform. Be sure it is properly installed and securely fastened
according to the manufacturer’s instructions for your safety. There is no set eye relief for your RXS-100 sight; therefore, you should
provide at least three inches of clearance between the viewing lens and your eye when in the shooting position. While 1X power/
magnication sights have unlimited eye-relief, always ensure there is an adequate amount of space between your face and the optic
to account for rearm recoil.
If mounting directly to an adapter plate (common for optics ready pistols), follow the manufacturer’s instructions for attaching the
adapter plate. Unless otherwise specied by the 3rd party manufacturer, be sure to remove any clearance by gently forward loading
the plate during fastening. When attaching the red dot sight to the adapter plate, gently forward load the sight body while fastening.
This both removes clearances that may otherwise shift under recoil and improves the chances of repeatable mounting should the red
dot sight need to be removed for any reason such as maintenance.
If using the included mount, loosen the socket head hex screw on the mount of the sight using the provided tool, so that the locking
bar can clamp around the rail. Position the mount on your base rail so that the cross-bolt engages a slot. Forward load the mount, so
that the crossbolt engages the forward face of the slot and clearance is removed. Tighten the hex bolt. CAUTION: Do not overtighten.
Torque should be set to 15 lb *in for the two sight-to-base screws and 20 lb *in for the base cross-bolt.f (pound-force inch) f
Remember, not all sights or scopes are compatible with all mounts on all firearms. If there is any doubt in your mind, you should seek
the advice of your local retailer or gunsmith.


Specyfikacje produktu

Marka: Bushnell
Kategoria: Lornetka
Model: RXS100

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Bushnell RXS100, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Lornetka Bushnell

Instrukcje Lornetka

Najnowsze instrukcje dla Lornetka

Pentax

Pentax 7x20 DCF Instrukcja

15 Października 2024
Auriol

Auriol Z31117 Instrukcja

12 Października 2024
Armasight

Armasight 8x36 Instrukcja

10 Października 2024
Kodak

Kodak BCS400 Instrukcja

9 Października 2024
Kodak

Kodak BCS600 Instrukcja

9 Października 2024
Steiner

Steiner M1050 LRF Instrukcja

8 Października 2024
Steiner

Steiner HX 10x42 Instrukcja

8 Października 2024