Instrukcja obsługi Axton ATB20A

Axton subwoofer ATB20A

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Axton ATB20A (12 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
INSTALLATION & OPERATION MANUAL
EINBAU & BEDIENUNGSANLEITUNG
8"/ 20 CM ACTIVE SUBWOOFER
ATB20A
– 2 –
Dear Customer
Thank you and congratulations on your purchase of the AXTON ATB20A. This active
subwoofer system exclusively uses very high quality parts and components. As with all
high-quality car audio components, professional installation is highly recommended.
If you plan on installing this active subwoofer by yourself, please read the following
installation guide carefully, before you attempt the installation. You should retain this manual,
the packaging and the purchasing receipt for future reference. For any further additional
information about mounting, connecting or adjusting this subwoofer system, please contact
your AXTON dealer.
UNPACKING THE SYSTEM
Carefully remove all parts from the giftbox and check whether they are in good undamaged
condition, and match with the set contents listed below:
ATB20A active subwoofer
Connector
Owner‘s manual
Please contact your authorized AXTON dealer, if the content of this set is incomplete,
or parts of it show signs of transport damage.
SPECIFICATIONS
8" / 20 cm active subwoofer
8" passive membrane for deep bass
Frequency response: 45 – 150 Hz
100 W rms x 1 @ 4 ohms (< 1.0 % THD / 14.4V)
9DULDEOH ¿OWHU ±  ORZSDVV  +]  G%RFW
Bass-Boost: 0 dB - 12 dB
RCA, adjustable input sensitivity: 150 mV – 5 V
High-Level, adjustable input sensitivity: 1.0 V – 16 V
Signal to noise ratio: > 90 dB
Dimensions W x H x D: 315 x 275 x 330 mm
Net Weight: 7.9 kg
– 4 –
SAFETY INSTRUCTIONS
1. This unit is designed to be used in a vehicle with a 12V battery and negative ground.
2. Before any wiring, always remove the negative terminal of the battery to prevent short-
circuiting. This is also the last lead to be (re-)connected.
3. Do not disassemble or alter the unit in any way, because that will void your warranty. Do
not attempt to repair or to service the unit yourself, but contact an authorized AXTON
dealer instead.
4. Use only original accessories which are designed and manufactured for the unit,
otherwise you will risk damage. Install the unit according to the mounting manual and
use only the supplied mounting accessories. The forces of acceleration for accidents are
sometimes huge. Heavy objects may pose a risk for the driver and the passengers of the
car, during an accident.
5. Protect the unit from water and other liquids, which can enter the casing. A short circuit
or even fire could be the result.
6. Before you replace a defective fuse, try to find the cause for the short circuit. Please
pay attention to the cables of the power supply! If the short circuit doesn‘t result from a
failure of the power supply or wiring, you can replace the defective fuse with a new one
of identical value. If the short-circuit still exists, please contact an authorized AXTON
dealer.
7. Be careful not to drain the car battery while using the unit when the car engine is turned
off. Because the unit uses a considerable amount of energy and the battery will be
charged only while the engine is running, it might happen that the battery will discharge
to a point where it‘s not longer possible to start the engine.
8. If your car is parked in direct sunlight and there is a considerable rise in temperature
inside the car, allow the unit to cool off before operation.
9. The amplifier module employs a protection circuit to protect the transistors and the
woofer if the amplifier malfunctions. The amplifier’s protection circuitry will shut-off the
amplifier in case of short-circuit, overload or DC offset at the speaker outputs or in case
of overheat. In case the cause for protection shut-off has been eliminated, the amplifier
will operate normally again (green LED ON/ Red LED OFF). Otherwise the amplifier will
continue to remain in protection mode.
10. Do not use the unit with a weak or old battery as its optimum performance depends on
a normal battery supply voltage.
11. Please pay attention to the music playback volume inside your vehicle, because you are
obliged to notice exterior sounds like a police siren or you might face penalties in case
of an accident or even loose your insurance cover.
12. Do not operate the unit in no other way than described in this manual. Failure to follow
the instructions within this manual will void your warranty.

Specyfikacje produktu

Marka: Axton
Kategoria: subwoofer
Model: ATB20A

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Axton ATB20A, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer Axton

Axton

Axton ATB220 Instrukcja

8 Października 2024
Axton

Axton ATB20A Instrukcja

29 Września 2024
Axton

Axton ATB216 Instrukcja

20 Września 2024
Axton

Axton ATB20STP Instrukcja

20 Września 2024
Axton

Axton AXB20A Instrukcja

18 Września 2024
Axton

Axton ATW20 Instrukcja

18 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

JL Audio

JL Audio SGR-10TW3 Instrukcja

13 Października 2024
Teufel

Teufel T6 Instrukcja

13 Października 2024
Polk

Polk DB1040 Instrukcja

10 Października 2024
OSD Audio

OSD Audio NERO DUAL X8 Instrukcja

9 Października 2024
OSD Audio

OSD Audio NERO WSA Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ102 Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ122 Instrukcja

9 Października 2024
Kicker

Kicker 43C84 Instrukcja

9 Października 2024
Kicker

Kicker 51CWQ124 Instrukcja

9 Października 2024
OSD Audio

OSD Audio FS12 Instrukcja

9 Października 2024