Instrukcja obsługi Axton ATB120

Axton subwoofer ATB120

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Axton ATB120 (11 stron) w kategorii subwoofer. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/11
8“/20 CM
ACTIVE SUBWOOFER
ACTIVE SUB
Installation & Operation Manual / Einbau- & Bedienungsanleitung
ATB120A
– 2 –
SAFETY INSTRUCTIONS
1. This unit is designed to be used in a vehicle with a 12V battery and negative ground.
2. Before any wiring, always remove the negative terminal of the battery to prevent short- circuiting.
This is also the last lead to be (re-)connected.
3. Do not disassemble or alter the unit in any way, because that will void your warranty. Do not
attempt to repair or to service the unit yourself, but contact an authorized AXTON dealer
instead.
4. Use only original accessories which are designed and manufactured for the unit, otherwise you
will risk damage. Install the unit according to the mounting manual and use only the supplied
mounting accessories. The forces of acceleration for accidents are sometimes huge. Heavy
objects may pose a risk for the driver and the passengers of the car, during an accident.
5. Protect the unit from water and other liquids, which can enter the casing. A short circuit or
even fire could be the result.
6. Before you replace a defective fuse, try to find the cause for the short circuit. Please pay
attention to the cables of the power supply! If the short circuit doesn‘t result from a failure of the
power supply or wiring, you can replace the defective fuse with a new one of identical value.
If the short-circuit still exists, please contact an authorized AXTON dealer.
7. Be careful not to drain the car battery while using the unit when the car engine is turned off.
Because the unit uses a considerable amount of energy and the battery will be charged only
while the engine is running, it might happen that the battery will discharge to a point where it‘s
not longer possible to start the engine.
8. If your car is parked in direct sunlight and there is a considerable rise in temperature inside the
car, allow the unit to cool off before operation.
9. The amplifier module employs a protection circuit to protect the transistors and the woofer if
the amplifier malfunctions. The amplifier’s protection circuitry will shut-off the amplifier in case
of short-circuit, overload or DC offset at the speaker outputs or in case of overheat. In case
the cause for protection shut-off has been eliminated, the amplifier will operate normally again
(green LED ON/ Red LED OFF). Otherwise the amplifier will continue to remain in protection
mode.
10. Do not use the unit with a weak or old battery as its optimum performance depends on a normal
battery supply voltage.
11. Please pay attention to the music playback volume inside your vehicle, because you are obliged
to notice exterior sounds like a police siren or you might face penalties in case of an accident
or even loose your insurance cover.
12. Do not operate the unit in no other way than described in this manual. Failure to follow the
instructions within this manual will void your warranty.
– 4 –
Dear Customer
Thank you and congratulations on your purchase of the AXTON ATB120A. This active subwoofer
system exclusively uses very high quality parts and components. As with all high-quality car audio
components, professional installation is highly recommended.
If you plan on installing this active subwoofer by yourself, please read the following installation
guide carefully, before you attempt the installation. You should retain this manual, the packaging
and the purchasing receipt for future reference. For any further additional information about
mounting, connecting or adjusting this subwoofer system, please contact your AXTON dealer.
UNPACKING THE SYSTEM
Carefully remove all parts from the giftbox and check whether they are in good undamaged condi-
tion, and match with the set contents listed below:
nATB120A active subwoofer
nConnector
nOwner‘s manual
Please contact your authorized AXTON dealer, if the content of this set is incomplete,
or parts of it show signs of transport damage.
SPECIFICATIONS
• 8” / 20 cm active subwoofer
• Frequency response: 60 – 220 Hz
• 100 W rms x 1 @ 4 ohms (< 1.0 % THD / 14.4V)
• Variable lowpass filter: 50 – 150Hz / 12 dB/oct.
• Bass-Boost: 0 dB - 12 dB
• Phase-Shift: 0 / 180 degrees
• RCA, adjustable input sensitivity: 150 mV – 5 V
• High-Level, adjustable input sensitivity: 1.0 V – 16 V
• Signal to noise ratio: > 90 dB
• Dimensions H x W x D: 135 x 485 x 345 mm

Specyfikacje produktu

Marka: Axton
Kategoria: subwoofer
Model: ATB120

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Axton ATB120, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje subwoofer Axton

Axton

Axton ATB120 Instrukcja

28 Grudnia 2024
Axton

Axton ATB220 Instrukcja

8 Października 2024
Axton

Axton ATB20A Instrukcja

29 Września 2024
Axton

Axton ATB216 Instrukcja

20 Września 2024
Axton

Axton ATB20STP Instrukcja

20 Września 2024
Axton

Axton AXB20A Instrukcja

18 Września 2024
Axton

Axton ATW20 Instrukcja

18 Września 2024

Instrukcje subwoofer

Najnowsze instrukcje dla subwoofer

Origin Acoustics

Origin Acoustics OSUB8 Instrukcja

28 Grudnia 2024
Origin Acoustics

Origin Acoustics OSUB12 Instrukcja

28 Grudnia 2024
Origin Acoustics

Origin Acoustics SUBDD12 Instrukcja

28 Grudnia 2024
Bazooka

Bazooka MBT1014 Instrukcja

27 Grudnia 2024
Bazooka

Bazooka MBT8014 Instrukcja

27 Grudnia 2024
PSB

PSB CustomSound CWS8 Instrukcja

27 Grudnia 2024
Soundstream

Soundstream Tarantula T5.152 Instrukcja

26 Grudnia 2024
Monitor Audio

Monitor Audio CLG-W12 Instrukcja

26 Grudnia 2024
JBL

JBL SSW-4 Instrukcja

26 Grudnia 2024
JBL

JBL SSW-2 Instrukcja

26 Grudnia 2024