Instrukcja obsługi Audio-Technica DJ Direct-Drive AT-LP1240-USB

Audio-Technica Sprzęt DJ-ski DJ Direct-Drive AT-LP1240-USB

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Audio-Technica DJ Direct-Drive AT-LP1240-USB (8 stron) w kategorii Sprzęt DJ-ski. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/8
AT-LP1240-USB Professional DJ Direct-Drive Turntable (USB and Analog)
Installation and Operation
2
Safety instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use the apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampli-
fiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with
one wider than the other. A grounding- type plug has two blades and a third grounding prong. The wide blade or
the third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician
for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/ accessories specified by the manufacturer.
12. Use only with a cart, stand, tripod, bracket or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination
to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged
in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been
dropped.
15. When the mains plug or appliance coupler is used as the disconnect device, it shall remain readily operable.
16. Please keep the unit in a good ventilation environment.
Professional DJ Direct-Drive Turntable
Introduction
Thank you for purchasing the AT-LP1240-USB Professional DJ Direct-Drive Turntable
(USB & Analog). This professional quality DJ turntable is designed primarily for DJ
use in nightclubs, touring and mobile applications. It can also be used by music
lovers to play their record collections at home. As an added benefit, the turntable
offers a USB output that allows direct connection to a computer for easy LP-to-
digital conversion. The turntable also features a built-in switchable phono/line
pre-amp that allows connection to a stereo system equipped with either a phono
or line-level input. Additional professional features for DJs include a sliding pitch
control, anti-skate control, start and brake control adjustments, reverse, and dual
start/stop controls.
Includes:
Removable dust cover, Audacity recording software, USB cable & adapter cables
The AT-LP1240-USB Professional DJ Direct-Drive Turntable System features
the following:
• Direct drive high-torque multi-pole motor for demanding DJ use
• USB output – no special drivers required for direct connection to your computer
• Selectable 33/45/78 RPM speeds
• Selectable internal stereo phono pre-amplifier
• Dual start/stop controls
• Start and brake control adjustments
• Sliding pitch control with quartz speed lock
• Reverse operation
• S-shaped tone arm assembly with:
· Adjustable counterweight
· Anti-skate adjustment
· Tone arm height adjustment and lock
· Tone arm lift with hydraulic action and lift lever
· Tone arm rest with locking mechanism
• Dedicated ground lug for tone arm grounding
• Stroboscopic platter and speed accuracy indicator
• Damped cast aluminum record platter with low-resistance DJ-style slip mat
• Removable stylus target light
• 45-RPM adapter
• Adjustable feet for leveling
• Removable dust cover
To assure maximum satisfaction from this product, please read the information
and follow the instructions presented in this manual. Please keep the manual in an
accessible location for future reference.
Unpacking
Carefully unpack the turntable and verify that the following parts are included and
intact:
• Slip mat (above the dust cover)
• Dust cover (above the turntable)
• Platter (under the turntable)
• 45 RPM adapter (accessory section)
• Counterweight (accessory section)
• Headshell (accessory section)
• Power cord (accessory section)
• USB cable
• Dual RCA (female) to 1
/8" (3.5 mm) mini-plug (male) stereo
adapter cable
• Dual RCA (female) to 1
/8" (3.5 mm) mini-plug (female) stereo
adapter cable
• Dual RCA (male) cable with integrated ground wire
• Stylus target light (accessory section)
• Audacity software (CD)
IT IS RECOMMENDED THAT ALL PACKAGING MATERIALS BE SAVED FOR
POSSIBLE FUTURE STORAGE, MOVING OR SHIPPING.
Caution:
To reduce the risk of electric shock, do not remove
any cover. No user-serviceable parts inside. Refer servicing
to qualified service personnel only.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol within the equilateral triangle is
intended to alert the use to the presence of un-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute
a risk of electric shock.
The exclamation point within the equilateral triangle is intended to alert the user
to the presence of important operation and maintenance (servicing) instructions
in the literature accompanying this appliance.
To prevent electric shock, do not use this polarized plug with an extension cord, receptacle or
other outlet unless the blades can be fully inserted to prevent blade exposure.
CAUTION
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with
liquids, such as vases, shall be placed on the apparatus.
WARNING
3
18
19
20
22
21
23
7 8 9 10 11
6
12
13
15
14
16
17
3 4 5
Main Features
Figure 1
1. POWER DIAL
Controls power to the unit.
2. DUAL START/STOP BUTTONS
Engages and disengages the motor/platter.
3. PLATTER SPEED BUTTONS
Select 33 or 45 RPM platter speed. (Note: 78 RPM is selected by
pressing both the 33 and 45 buttons simultaneously; both buttons
should be illuminated.)
4. PLATTER
Cast aluminum platter mounts directly to center spindle/motor shaft.
5. STROBE DOTS (on platter edge)
Operate in conjunction with stroboscopic light located under the
power dial (1) to provide visual indication of accurate platter speeds.
6. CENTER SPINDLE
Precision-machined platter mount on motor shaft.
7. REMOVABLE STYLUS TARGET LIGHT
Provides illumination directed at the stylus position for easier cueing
in low light. Easily plugs into jack on top of turntable deck.
8. START CONTROL KNOB
Rotate the start control knob to increase or decrease platter start
time between 0.2 – 6.0 seconds. (Minimum setting is the quickest
start; maximum setting is the slowest start to reach selected speed.)
9. BRAKE CONTROL KNOB
Rotate the brake control knob to increase or decrease platter brake
time between 0.2 – 6.0 seconds. (Minimum setting is the quickest
stop; maximum setting is slowest.)
10. REVERSE CONTROL KNOB
Controls platter’s rotational direction.
11. SELECT SPEED RANGE
Select +/- 10 or 20% speed range. (Note: +/-50% is selected by
pressing both the 10 and 20 buttons simultaneously.)
12. HEADSHELL
Standard, interchangeable stereo cartridge headshell.
13. HEADSHELL LOCKING RING
Rotate counter-clockwise (to the left) to draw the inserted headshell
firmly into its seated, locked position. Rotate the ring a full turn to
the right to permit removal of the headshell.
14. QUARTZ BUTTON
This button is used to turn the pitch function on and off. When
the Quartz is activated the platter will hold the RPMs at 0% pitch,
regardless of the pitch slider position and speed range control settings.
15. PITCH ADJUST SLIDE CONTROL
Use in conjunction with pitch button to vary the platter’s rotational
speed. In the center detent position quartz lock is active.
16. TONE ARM ASSEMBLY HEIGHT ADJUST
Raises and lowers the entire tone arm assembly to allow the tone
arm to remain parallel to the record surface.
17. TONE ARM LIFT
Elevates tone arm above record surface.
18. TONE ARM REST WITH LOCKING CLAMP
Locking clamp secures tone arm during transport.
19. TONE ARM LIFT CONTROL LEVER (“Cueing Lever”)
Controls action of tone arm lift. (Note: Lift mechanism is
hydraulically damped to slow tone arm descent.)
20. ANTI-SKATE CONTROL
Applies a small outward force to the tone arm, counteracting the
tendency of the tone arm to move inward toward the center of
the record.
21. TONE ARM ASSEMBLY HEIGHT LOCK
(Hidden under counterweight in drawing.)
Locks the tone arm height setting. (Always fully unlock before
attempting to make a height adjustment.)
22. COUNTERWEIGHT
Balances the tone arm and provides adjustment for proper
downward tracking force on the stylus.
23. 45-RPM ADAPTER (Shown in receptacle)
Adapt 7" records with large center holes to fixed center spindle.

Specyfikacje produktu

Marka: Audio-Technica
Kategoria: Sprzęt DJ-ski
Model: DJ Direct-Drive AT-LP1240-USB

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Audio-Technica DJ Direct-Drive AT-LP1240-USB, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Sprzęt DJ-ski Audio-Technica

Audio-Technica

Audio-Technica AT-XP7 Instrukcja

6 Grudnia 2024
Audio-Technica

Audio-Technica AT6006R Instrukcja

6 Grudnia 2024
Audio-Technica

Audio-Technica AT-VM95EN Instrukcja

29 Września 2024
Audio-Technica

Audio-Technica AT-PL50 Instrukcja

3 Września 2024
Audio-Technica

Audio-Technica DJ Direct-Drive AT-LP1240-USB Instrukcja

3 Września 2024
Audio-Technica

Audio-Technica AT-LP60 Instrukcja

31 Sierpnia 2024
Audio-Technica

Audio-Technica AT-PL120 Instrukcja

31 Sierpnia 2024
Audio-Technica

Audio-Technica AT-LP120-USB Instrukcja

25 Sierpnia 2024
Audio-Technica

Audio-Technica AT-VM95SP/H Instrukcja

19 Sierpnia 2024
Audio-Technica

Audio-Technica AT-VM95ML Instrukcja

13 Sierpnia 2024

Instrukcje Sprzęt DJ-ski

Najnowsze instrukcje dla Sprzęt DJ-ski

MWM

MWM Essential Phase Instrukcja

11 Grudnia 2024
Korg

Korg Rhythm Master Instrukcja

10 Grudnia 2024
Korg

Korg PuttRhythm Instrukcja

10 Grudnia 2024
Pioneer

Pioneer RB-DMX1 Instrukcja

7 Grudnia 2024
Pioneer

Pioneer OPUS-QUAD Instrukcja

7 Grudnia 2024
Pioneer

Pioneer HDJ-X5-K Instrukcja

7 Grudnia 2024
Vonyx

Vonyx DB20 Instrukcja

4 Grudnia 2024
Vonyx

Vonyx DB10 Instrukcja

4 Grudnia 2024
Festo

Festo CPX-E-CEC-M1 Instrukcja

9 Października 2024
BeamZ

BeamZ StarFuzer Instrukcja

9 Października 2024