Instrukcja obsługi AstralPool HydroSpin Compact
AstralPool
filtr do wody
HydroSpin Compact
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AstralPool HydroSpin Compact (20 stron) w kategorii filtr do wody. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/20
H y d r o S p i n
INSTALLATION AND MAINTENANCE MANUAL
MANUEL D’INSTALLATION ET D’ENTRETIEN
MANUAL DE INSTALACIÓN Y MANTENIMIENTO
MANUALE DI INSTALAZIONE E MANUTENZIONE
EINBAU-UND BETRIEBSANLEITUNG
MANUAL DE INSTRUÇÕES E MANUNTENÇÃO
Compact
2
1 4 3
2
ENGLISH
IMPORTANT: The instruction manual you are holding includes essential information on the safety measures to be
implemented for installation and start-up. Therefore, the installer as well as the user must read the instructions before
beginning installation and start-up.
Keep this manual for future reference.
To achieve optimum performance of the HydroSpin Compact, follow the instructions provided below:
1. CONTENTS
Inside the box you will find the following components:
1. HydroSpin Compact
2. Multi-support
3. Bag of accessories*
4. Installation and maintenance manual
*Ball valve 3/4" Stainless Steel AISI 316, 2
connections for glueing Ø50 or screwing to 2 1/4", 2
joints, 1 outlet elbow, 3 nuts and 3 anchor bolts.
2. GENERAL CHARACTERISTICS
The HydroSpin has been designed to work in all new and existing water installations.
Installing the HydroSpin in filtration systems from 3 to 16,5 m³/h and up to a maximum pressure of 2.5 bars is
recommended.
The HydroSpin:
Significantly reduces water lost in drainage when cleaning the filters.
Reduces the frequency with which the filtration system is cleaned.
The HydroSpin accumulates the separated solids in its lower part, which are then ejected by opening the purge
valve. This should be opened before the waste surpasses the limit indicated in Fig. 1 - pag.16.
3. INSTALLATION
The HydroSpin should be installed between the pump and the filter.
Ensure there is a drain in the area where the HydroSpin is located.
Ensure that the HydroSpin is installed on a horizontal surface.
There should be sufficient space around the HydroSpin to carry out
the inspections and maintenance that will be necessary during its
lifetime.
Wall installation:
1. Mark the three holes on the wall of the support.
2. Make the 3 Ø 8mm holes.
3. Screw in the support.
4. Position the Hydrospin Compact.
5. Join simple or 3 piece unions of Ø50 in the HydroSpin entrance
and exit.
6. Using valves in both the entrance and exit is recommended.
7. Thread the purge valve into the
lower part of the HydroSpin,
putting teflon in the thread.
Check that it is closed.
8. Join tubing from the HydroSpin
purge, to drainage (Fig. 2 -
pag.16).
9. Installation of a manometer in
the HydroSpin inlet is
recommended. (Fig. 3 - pag.16).
10. Switch on the pump.
3
Soil installation:
1. Mark the three holes on the wall of the support.
2. Make the 3 Ø 8mm holes.
3. Follow on from point 5 in the previous section.
Note: an electrovalve may be connected to the purge exit in order to temporize
cleanings.
4. MAINTENANCE
Purging: before the limit set out in Fig. 1 - pag.16 is reached, the HydroSpin should
be purged by opening the lower valve when accumulated waste can be seen.
When carrying out this operation it is neither necessary to stop the filter system nor
to turn the filter valve key.
5. TROUBLE-SHOOTING
If you notice that the pressure reading has risen considerably on the HydroSpin entrance manometer, it may be due
to:
a) The filter is dirty: check the pressure of the filter's manometer, and if it has risen, carry out its cleaning
operation. (Follow the steps in the filter's instruction manual). Afterwards, check that the HydroSpin's
entrance manometer pressure has decreased.
b) The HydroSpin is blocked: check the pressure of the Filter's
manometer, if this is the same or the pressure has decreased, it
means that there is one or more blockages within the HydroSpin,
in which case the following steps must be taken to unblock it:
1. Stop the filtration system.
2. Shut off the system's suction and discharge valves.
3. Purge the waste and water by opening the lower valve.
4. Unscrew the two nuts in the 8 caps.
5. Separate the central body, taking care with the joint.
6. Separate the diffuser (pressure)
7. To extract the body of cyclones, turn them firmly to the right
until snug (about 2 centimetres of movement)
8. Take out the 6 top screws.
9. Check that there are no obstructed cyclones (holes) and wash
the whole piece with pressurized water, going over all the
cyclones once again.
10. Once everything has been washed, assemble the whole in
reverse order to that described above, position the joint
snugly in its place and screw in the 8 screws around the
perimeter tightly.
Attention:
If you detect that the accumulated dirt inside the Hydrospin Compact has a
very uneven surface it is possible that there is some obstruction in one of the
cyclones, follow step b) described previously (Fig. 4 page. 16).
When it is running check that the HydroSpin does not lose water through
the caps.
Check that the pressure on both the HydroSpin and Filter manometers is similar.
6. SAFETY WARNINGS
Do not install HydroSpin in facilities with a cleaning system with active oxygen or its derivates.
Do not connect the HydroSpin directly to the water network as the pressure may be very high and exceed the
maximum pressure supported by the equipment.
Do not use the filtration circuit for filling up and regulating the swimming pool water level. An error in its use
could cause overpressure in the filter.
Do not clean the e its propertiquipment with any kind of solvent, as it could lose es (shine, transparency...)
In filtration installations with diatomeaceous filters, a bypass between the pump and the filter must be made so
that the HydroSpin does not separate the diatomeaceous earth when it is introduced into the filtration system;
the when doing so close the connections to the HydroSpin.
Specyfikacje produktu
| Marka: | AstralPool |
| Kategoria: | filtr do wody |
| Model: | HydroSpin Compact |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z AstralPool HydroSpin Compact, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje filtr do wody AstralPool
7 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
7 Września 2024
Instrukcje filtr do wody
- filtr do wody Electrolux
- filtr do wody Philips
- filtr do wody GE
- filtr do wody BRITA
- filtr do wody Hyundai
- filtr do wody Fisher & Paykel
- filtr do wody Fiap
- filtr do wody Grohe
- filtr do wody Juwel
- filtr do wody Ecowater
- filtr do wody Franke
- filtr do wody Eheim
- filtr do wody Flama
- filtr do wody Ionmax
- filtr do wody PUR
Najnowsze instrukcje dla filtr do wody
2 Października 2024
29 Września 2024
24 Września 2024
11 Września 2024
22 Sierpnia 2024
7 Sierpnia 2024
18 Czerwca 2024
27 Maja 2024
26 Maja 2024
25 Maja 2024