Instrukcja obsługi AMX NX-3200

AMX Kontroler NX-3200

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX NX-3200 (48 stron) w kategorii Kontroler. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/48
Ha r d w a r e R e f e r e n c e M a n u a l
C e n t r a l Con t r o l l e r s
NX-Series
NetLinx Integrated Controllers
NX-1200, NX-2200
NX-3200, NX-4200
L a t e st R e l e a se : 5 / 0 4 / 2 0 1 5
NX-Series NetLinx Integrated Controllers Hardware Reference Guide
AMX DOMESTIC CHANNEL PARTNER and END CUSTOMER LIMITED
WARRANTY, DISCLAIMER AND LICENSE
(Excerpt from CHANNEL PARTNER TERMS AND CONDITIONS Versions 11.17.2011 with updates for previous version
8.25.2010 [sections 6.1 (a), (b) and (f)])
Definitions
“End Customer” means an authorized end customer with direct in warranty privileges from AMX. Within this limited warranty,
disclaimer and license document, “End Customer” shall have the same meaning as “Channel Partner” with the noted exceptions
of Sections 6.5 through 6.9 which are not applicable or available to End Customer’s directly from AMX. Offerings described in
Sections 6.5 through 6.9 are available to End Customer only through their selected authorized AMX Channel Partner.
6. LIMITED WARRANTY; RETURN, REPAIR AND REPLACEMENT
6.1 AMX warrants the Products to be free of material defects in materials and workmanship under normal use for three (3)
years from the Shipping Date (or such other period as may be specified below), subject to the following limitations and
exceptions (“Limited Warranty”). For any Product, “Warranty Period” means the period during which the Limited Warranty
is in effect, as set forth herein.
(a) LCD and LED panels are warranted for three (3) years from the Shipping Date, except for the display and touch
overlay components, which are warranted for a period of one (1) year from the Shipping Date.
(b) Disk drive mechanisms, pan/tilt heads and external power supplies are warranted for a period of one (1) year from the
Shipping Date.
(c) AMX lighting Products are warranted to switch on and off any load that is properly connected to our lighting Products,
as long as the AMX lighting Products are under warranty. AMX also warrants the control of dimmable loads that are
properly connected to our lighting Products. The dimming performance or quality thereof is not warranted, due to the
random combinations of dimmers, lamps and ballasts or transformers.
(d) AMX software and firmware included in the Products is warranted for a period of ninety (90) days from the Shipping
Date.
(e) Batteries and incandescent lamps are not covered under the Limited Warranty.
(f) The Warranty Period for AMX AutoPatch EPICA, Enova DGX, Modula, Modula Series 4, Modula Cat Pro Series and
8Y-3000 Product models will continue for the original installation until five (5) years after the issuance of a PDN with
respect to termination of the applicable Product model. However, if the Product is moved from its original installation
to a different installation, the Warranty Period will automatically become three (3) years from the Shipping Date and, if
more than three (3) years have elapsed since the Shipping Date, the Warranty Period will automatically expire.
DLI-6293353v1
Note: Refer to www.amx.com to view/download the latest complete AMX Warranty and Return Policies.
Notices
Copyright Notice
AMX© 2013, all rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of
AMX. Copyright protection claimed extends to AMX hardware and software and includes all forms and matters copyrightable
material and information now allowed by statutory or judicial law or herein after granted, including without limitation, material
generated from the software programs which are displayed on the screen such as icons, screen display looks, etc.
Reproduction or disassembly of embodied computer programs or algorithms is expressly prohibited.
No patent liability is assumed with respect to the use of information contained herein.
Liability Notice
While every precaution has been taken in the preparation of this publication, AMX assumes no responsibility for error or
omissions. No liability is assumed for damages resulting from the use of the information contained herein.
Further, this publication and features described herein are subject to change without notice.
Lithium Batteries Notice
Switzerland requires the following notice for products equipped with lithium batteries. This notice is not applicable for all AMX
equipment.
Upon shipment of the products to Switzerland, the requirements of the most up-to-date Swiss Ordinance Annex 2.15 of SR
814.81 will be met including provision of the necessary markings, documents, and annual reports relative to the disposal of the
batteries to the Swiss Authorities.
Trademark Notices
AMX®, Enova®, AutoPatch®, NetLinx®, DXLink™, SmartScale®, and InstaGate Pro® are trademarks of AMX.
Windows is a registered trademark of Microsoft Corporation in the United States and other countries.
3M™, Desco®, Richmond Technology®, and Plastic Systems® are registered trademarks.
Ethernet® is a registered trademark of the Xerox Corporation.
ENERGY STARR is a registered trademark of the U.S. Department of Energy and the U.S. Environmental Protection Agency
Other products mentioned herein may be the trademarks of their respective owners.
Warnings and Cautions
This manual uses the following conventions and icons to draw attention to actions or conditions that could potentially cause
problems with equipment or lead to personal risk:
ESD Warning
To avoid ESD (Electrostatic Discharge) damage to sensitive components, make sure you are properly grounded before touching
any internal materials.
When working with any equipment manufactured with electronic devices, proper ESD grounding procedures must be followed
to make sure people, products, and tools are as free of static charges as possible. Grounding straps, conductive smocks, and
conductive work mats are specifically designed for this purpose.
Anyone performing field maintenance on AMX DXLink equipment should use an appropriate ESD field service kit complete with
at least a dissipative work mat with a ground cord and a UL listed adjustable wrist strap with another ground cord. These items
should not be manufactured locally, since they are generally composed of highly resistive conductive materials to safely drain
static charges, without increasing an electrocution risk in the event of an accident. ESD protective equipment can be obtained
from 3M™, Desco®, Richmond Technology®, Plastic Systems®, and other such vendors.
ESD Warning: The icon to the left indicates text regarding potential danger associated with the discharge
of static electricity from an outside source (such as human hands) into an integrated circuit,
often resulting in damage to the circuit.
Warning: The icon to the left indicates text that warns readers against actions or conditions that
could cause potential injury to themselves.
Caution: The icon to the left indicates text that cautions readers against actions that could cause
potential injury to the product or the possibility of serious inconvenience.

Specyfikacje produktu

Marka: AMX
Kategoria: Kontroler
Model: NX-3200

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z AMX NX-3200, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kontroler AMX

AMX

AMX NXA-WAPZD1100 Instrukcja

28 Września 2024
AMX

AMX Mio Modero R-2 Instrukcja

28 Września 2024
AMX

AMX NX-3200 Instrukcja

28 Września 2024

Instrukcje Kontroler

Najnowsze instrukcje dla Kontroler

DJI

DJI Motion Controller Instrukcja

14 Stycznia 2025
8BitDo

8BitDo Ultimate C Wired Controller Xbox Instrukcja

11 Stycznia 2025
Balam Rush

Balam Rush Kontrol React G575 Instrukcja

11 Stycznia 2025
PCE Instruments

PCE Instruments PCE-RE100P Instrukcja

10 Stycznia 2025
PCE Instruments

PCE Instruments PCE-RE21R Instrukcja

10 Stycznia 2025
Sonance

Sonance VC30R Instrukcja

8 Stycznia 2025
BeamZ

BeamZ WTR10-5 Instrukcja

5 Stycznia 2025
Audibax

Audibax MC1000 Instrukcja

5 Stycznia 2025
Somfy

Somfy Keypad 2 RTS Instrukcja

1 Stycznia 2025
Somfy

Somfy Keypop RTS Instrukcja

1 Stycznia 2025