Instrukcja obsługi AMX MVP-TDS-9

AMX ładowarka do urządzeń mobilnych MVP-TDS-9

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AMX MVP-TDS-9 (1 stron) w kategorii ładowarka do urządzeń mobilnych. Ta instrukcja była pomocna dla 11 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/1

Installation Guide

MVP-TDS-9 Table Docking Station

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

2/11

AMX reserves the right to alter specifications without notice at any time.

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

93-5967-10 REV: C

Overview

The Power-over-Ethernet MVP-TDS-9 Table Docking Station (FIG. 1) charges

the MVP-9000i and provides a wired Ethernet connection when the panel is

docked. The MVP-TDS-9's sleek design allows the panel to slide into perfect

placement in the docking station and includes password protection support for

panel removal. When the MVP-9000i is placed into the PoE docking station, it

automatically switches from wireless to wired Ethernet communication. The

Docking Station is available in either black (MVP-TDS-9-GB, FG5967-10) or

white (MVP-TDS-9-GW, FG5967-11).

Specifications

Powering the MVP-TDS-9

The MVP-TDS-9 uses the PS-POE-AT High-Power PoE Injector to provide direct

power for the MVP panel via a standard Ethernet connection, both for standard

function and for charging its internal battery. This also allows a wired Ethernet

connection for the panel, and the panel may be used normally while docked in

the MVP-TDS-9 without the need for a wireless connection.

NOTE: Use the included RJ45 plug for connecting the included Ethernet cable to the

MVP-TDS-9. Other RJ45 plugs will not fit in the device’s jack, and attempting to use

another plug may damage the jack.

1. Turn the device upside down and connect one end of the Ethernet cable to

the PWR RJ45 connector on the bottom of the MVP-TDS-9.

2. To prevent wear on the Ethernet cable and assure that the device’s base is

in full contact with the table surface, press the cable into the locking groove

running across the bottom of the device (FIG. 2).

3. The other end of the included Ethernet cable has an input port, intended for

a standard RJ45 jack. Use a standard Ethernet cable to connect the 

Ethernet/PoE port to the PS-POE-AT plugging the other end of the Ether-

net cable into the Data & Power Out RJ45 port on the PS-POE-AT. Make

sure that the PS-POE-AT’s power cable is connected to the device and to

an available power source, and that the incoming Ethernet cable accessing

the Data In RJ45 jack is connected to the desired network.

4. Place the touch panel in the Docking Station cradle bottom-first and make

sure the device is fully seated in the Docking Station. When fully seated,

the touch panel’s docking station connector should be in contact with the

Docking Station’s charger pins (FIG. 2).

For more information on the PS-POE-AT, please refer to the PS-POE-AT High-

Power PoE Injector Installation Guide, available from www.amx.com.

Recharging

To recharge the MVP-9000i, slide the device into the Table Docking Station

cradle bottom-first and make sure the device is fully seated in the Docking

Station. The charger pins in the bottom of the cradle (FIG. 2) must be in contact

with the connector on the bottom of the MVP-9000i for it to start recharging. The

MVP panel will stop recharging automatically once the battery has achieved its

maximum charge. The MVP panel will also switch automatically from a wireless

to a wired Ethernet connection.

For more information on transferring files, please refer to the MVP-9000i Modero

Viewpoint Widescreen Touch Panel Operation/Reference Guide, available at

www.amx.com.

Removing the MVP-9000i from the MVP-TDS-9

The center front of the MVP-TDS-9 contains one capacitive touch Release

button. This button, when pressed, switches the MVP panel from a wired to a

wireless Ethernet connection and disconnects the latch holding the panel to the

MVP-TDS-9. The panel may be removed from the device at that time.

NOTE: The MVP panel CANNOT be removed from the MVP-TDS-9 during a software

or firmware download. The panel can only be removed when the download is

complete.

NOTE: Charging Lithium Polymer batteries at high temperature will reduce the battery

life. Industry guidelines dictate that batteries should not be charged at temperatures

above 45° C (113° F). The temperature is determined by a combination of the ambient

temperature where the panel is located, plus temperature increases normally

occurring inside electronic devices containing batteries. AMX has implemented

battery temperature monitoring features to maximize the rate of battery charging, while

staying within industry temperature guidelines.

Battery charge times will increase in installations where the room temperature is

above 25° C (77° F), and may be temporarily suspended at room temperatures above

30° C (86° F). Battery charging will automatically resume once the temperature has

fallen to appropriate levels. Minimizing the display backlight intensity and turning off

the backlight during periods of non-use will also yield faster charge times.

FIG. 1 MVP-TDS-9-GB Table Docking Station (FG5967-10)

MVP-TDS-9 Specifications

Dimensions

(HWD): • 6.25” x 11.50” x 5.50” (15.88cm x 29.21cm x 13.97cm)

Weight: • 1.25 lbs (.57 kg)

Power 





Requirements:

• 30 W (Class II listed power supplemented), supplied via the

PS-POE-AT High-Power PoE Injector.

Startup Power

Requirements:

• Cradle and panel (not charging): 16 W

• Cradle and panel (charging): 23 W

• Ejection: 23 W

Front Panel 





Components:

• Docking Station cradle: for supporting the device while

connected or charging.

• Release button: before removing the MVP touch panel, press

this button to switch the panel from a wired to a wireless

Ethernet connection to its network.

• 12-pin charging connector on bottom of device cradle.

Rear Panel 





Components:

• 2 USB ports on the left side of the device, for firmware or file

download to a docked touch panel. These ports may also be

used for using a keyboard and/or mouse with the touch

panel.

Operating/





Storage





Environments:

• Operating Temperature: 0° C (32° F) to 40° C (104° F)

• Battery Charging Temperature: 0° C (32° F) to 30° C (86° F)

• Operating & Battery Charging Humidity: 20% to 85% RH

• Storage Temperature: -10° C (-14° F) to 60° C (140° F)

• Storage Humidity: 5% - 85% RH

Included 





Accessories

• MVP-TDS-9 Table Docking Station Installation Guide 

(93-5967-10)

• PS-POE-AT High Power PoE Injector (FG423-81)

• Ethernet cable - black (ECA5967-22BL) (for 

MVP-TDS-9-GB)

• Ethernet cable - white (ECA5967-22WH) (for 

MVP-TDS-9-GW)

Other AMX 





Equipment:

• MVP-9000i Modero Viewpoint Widescreen Touch Panel with

Intercom - Black (FG5967-01)

• MVP-9000i Modero Viewpoint Widescreen Touch Panel with

Intercom - White (FG5967-02)

Docking Station cradle

Release button

FIG. 2 MVP-TDS-9-GB - Rear view

Charger pins

Docking Station cradle

Locking groove

USB ports (2)

Specyfikacje produktu

Marka:	AMX
Kategoria:	ładowarka do urządzeń mobilnych
Model:	MVP-TDS-9
Kolor produktu:	Czarny
Rodzaj zasilania:	Prąd przemienny
Wysokość produktu:	159 mm
Szerokość produktu:	292 mm
Głębokość produktu:	139 mm
Waga produktu:	57 g
Maksymalna moc:	3 W
Zakres temperatur (eksploatacja):	0 - 40 °C
Zakres wilgotności względnej:	20 - 85 %
Liczba portów USB 2.0:	2
Wymiary produktu (SxGxW):	292 x 139 x 159 mm
Kompatybilność:	MVP-9000i
Maksymalna temperatura eksploatacji:	40 °C
Złącze(a):	12-pin
Wbudowana bateria:	Nie
Rozmiar:	9 "
Typ ładowarki:	Wewnętrzna
Kompatybilność ładowarki:	Tablet