Instrukcja obsługi AFX Evanston EVNP2532LAJUDSN
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla AFX Evanston EVNP2532LAJUDSN (2 stron) w kategorii Lampa. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/2
Indoor Luminaire
Evanston Pendant
120~277VAC / 60Hz
Page 1 of 2 8061256 R0
Model EVNP2532LAJUDSN #
Safety Precautions
Read all safety precautions and installation instructions carefully before installing or servicing this xture. Failure to comply with these instructions could result in
potentially fatal electric shock and/or property damage.
It is recommended that a qualied electrician perform all wiring. This fixture must be wired in accordance with all national and local electrical codes.
Do not handle any energized xture or attempt to energize any xture with wet hands or while standing on a wet or damp surface or in water.
This xture is designed for use in a 120-277VAC, 60Hz fused circuit. The xture is compatible with Triac (forward-phase or leading edge) / ELV (reverse phase or trailing
edge) and 0-10 V dimmers. Make sure that the power source conforms to the requirements of the xture. (See labels on the xture housing).
To reduce the risk of electrical shock, and to assure proper operation, this xture must be adequately grounded. To accomplish proper grounding, there must be a
separate ground wire (green) contact between this xture and the ground connection of your main power supply panel.
This xture is intended to be used for general indoor lighting in dry or damp wet locations.
Disclaimer
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. NOTE: This
equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules and Canadian ICES-005 (B) / NMB-005
(B). These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiver antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
• Consult with the dealer or an experienced radio/TV technician for help.
Any modications to this xture may void the warranty and interfere with the safe operation of the luminaire.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Assembly Instructions
1. Preparing for installation-
A. before installing or servicing any part of this xture. Disconnect electrical power
B. Remove xture from box. Separate contents of parts bag.
2. Fixture Assembly.
A. Attach xture shade (1) to xture LED pan (2) using 6 provided screws (3). Hand
tighten to make sure they are secured tightly. Do not over tighten and strip threads.
B. Choose desired height for xture stems using any , stems of the 6” 12” & 18”
provided to achieve your preferred hang length to the top of the shade.
C. Feed xture wiring from top of shade up through both stems that are going to be
used all the way through the Hang Straight into the canopy.
D. Starting with the bottom stem thread each stem together one at a time until the
Canopy is securely tightened to the stems.
E. Tighten the stems to the canopy at the three locations with the desired stem lengths
to get the look wanted.
3. Wiring- all wiring must take place inside junction box.
Caution: Make sure power is o at fuse or circuit breaker box. Check power wires for any damage or scrapes. Use wire suitable for at least 90C (194F).
Note: Most dwellings built before 1985 have supply wire rated to 60C. Consult a qualied electrician before installing.
A. ical shock, overheating, low or no light output, and This unit will not operate properly unless connected to a “grounded” electrical circuit. Electr
shortened LED life can result if proper grounding is not done. Securely attach power source ground wire and xture ground wire to green ground
screw on circular mounting bracket.
B. r NEC (National Electrical Code) requirements, cut the co Then remove the ends of the three wires for Fo rd about 7” above the canopy. 3/8” from
connection purposes.
C. . Fixture will operate normally w/o connection to any dimmers. Connect white xture lead to white (N) wire from supply For none-dimming xture
power source. Connect black xture lead to black (L) wire from supply power source. Gray and purple wires are not to be used and must be
individually capped to prevent shorting.
D. Connect white xture lead to (N) wire from dimming source per dimmer wiring instructions. Connect black xture lead to For TRIAC dimming.
black (L) wire from dimmer supply power source. Gray and purple wires are not to be used and must be individually capped to prevent shorting.
E. . Connect gray wire from the xture to the dimmer source gray wire. Connect purple wire from the xture to the For (0-10V) dimming xture
dimmer source purple wire. Connect white xture lead to white (N) wire from supply power source. Connect black xture lead to black (L) wire from
dimmer supply power source.
F. . Pull on each wire lead to make sure connections are secure. Make certain no bare wires are exposed outside of wire Do not mix wires
connectors. Tuck all connections neatly into junction box.
Limited Factory Warranty
AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 5 years from the date of shipment from the factory. This warranty covers all component parts and extends only to
replacement of defective xture or components: it does not cover failure due to improper installation, misuse, mishandling or damage
incurred in transit.
Indoor Luminaire
Evanston Pendant
120~277VAC / 60Hz
Page 2 of 2 8061256 R0
Model # EVNP2532LAJUDSN
4. Color Changing Temperature Adjustment, CCT (if desired).
A. Adjust the two switches on each board accordingly to the desired color temperature as seen below. All boards must be set the same way. Fixture is preset Note:
to 3500K from factory.
5. Ceiling Mounting.
A. Align mounting gem bar ) over tapped holes in the junction box (Not Included) Secure mounting cross bar to the junction box with two provided screws (5), (4 .
making sure the gem bar ) is tight up against the ceiling. (4
B. Lift xture ) with stem and canopy ) ush up to ceiling aligning two threaded stems (7) with clearance holes in the canopy (6 (1 (6 ).
C. Secure the xture canopy (6) ush to ceiling with the two decorative thumb nuts (8) provided.
D. Place diuser (9) inside shade resting on bottom ring to give the nished look.
6. Restore power at the fuse or breaker box.
Limited Factory Warranty
AFX Inc. hereby warranty that this xture is free from defects in materials and workmanship when installed and used under normal operating
conditions for a period of 5 years from the date of shipment from the factory. This warranty covers all component parts and extends only to
replacement of defective xture or components: it does not cover failure due to improper installation, misuse, mishandling or damage
incurred in transit.
Specyfikacje produktu
| Marka: | AFX |
| Kategoria: | Lampa |
| Model: | Evanston EVNP2532LAJUDSN |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z AFX Evanston EVNP2532LAJUDSN, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Lampa AFX
12 Października 2024
12 Października 2024
12 Października 2024
12 Października 2024
Instrukcje Lampa
- Lampa Sony
- Lampa Ikea
- Lampa Samsung
- Lampa Beurer
- Lampa Sanitas
- Lampa BeamZ
- Lampa Philips
- Lampa Livoo
- Lampa Thule
- Lampa Toolcraft
- Lampa Canon
- Lampa Nedis
- Lampa OK
- Lampa Adler
- Lampa Westinghouse
- Lampa Fenix
- Lampa August
- Lampa Niceboy
- Lampa Einhell
- Lampa Prixton
- Lampa Mesko
- Lampa Honeywell
- Lampa Chauvet
- Lampa Steinel
- Lampa Akasa
- Lampa ArmyTek
- Lampa Petzl
- Lampa Kodak
- Lampa Smart
- Lampa ORNO
- Lampa Dyson
- Lampa Godox
- Lampa Medisana
- Lampa Flex
- Lampa Konig & Meyer
- Lampa Trust
- Lampa DEDRA
- Lampa Hilti
- Lampa Digitus
- Lampa Vimar
- Lampa V-TAC
- Lampa Ledlenser
- Lampa Eurolite
- Lampa Emos
- Lampa NightStick
- Lampa Osram
- Lampa Ansmann
- Lampa Velleman
- Lampa Klarstein
- Lampa Güde
- Lampa Pyle
- Lampa Adviti
- Lampa Nordlux
- Lampa Camry
- Lampa Werma
- Lampa ARRI
- Lampa Ibiza Sound
- Lampa IVT
- Lampa Kanlux
- Lampa Brilliant
- Lampa Genie
- Lampa G3 Ferrari
- Lampa Axis
- Lampa NEO Tools
- Lampa Carson
- Lampa Innoliving
- Lampa Abus
- Lampa Bresser
- Lampa Livarno Lux
- Lampa Elro
- Lampa Hama
- Lampa Zafferano
- Lampa Duronic
- Lampa Cameo
- Lampa Barco
- Lampa Goobay
- Lampa Schwaiger
- Lampa Gravity
- Lampa Elation
- Lampa Denver
- Lampa Berger & Schröter
- Lampa Futurelight
- Lampa Nitecore
- Lampa Tracer
- Lampa Craftsman
- Lampa Olight
- Lampa Black Diamond
- Lampa Media-Tech
- Lampa Levenhuk
- Lampa BenQ
- Lampa Martin
- Lampa PowerPlus
- Lampa HiKOKI
- Lampa Workzone
- Lampa EasyMaxx
- Lampa Alecto
- Lampa Avidsen
- Lampa Aputure
- Lampa Dörr
- Lampa SLV
- Lampa Karma
- Lampa Smartwares
- Lampa Elgato
- Lampa ETC
- Lampa Sygonix
- Lampa Cotech
- Lampa Profoto
- Lampa ATN
- Lampa Brennenstuhl
- Lampa Eglo
- Lampa Lucide
- Lampa Eminent
- Lampa Hähnel
- Lampa Silva
- Lampa Steren
- Lampa Hansa
- Lampa Lumie
- Lampa Livarno
- Lampa Royal Sovereign
- Lampa Melinera
- Lampa In Lite
- Lampa Näve
- Lampa Luceplan
- Lampa Massive
- Lampa Runtastic
- Lampa Steinhauer
- Lampa Topeak
- Lampa Zuiver
- Lampa Konig
- Lampa X4-Tech
- Lampa Hella
- Lampa HQ
- Lampa Nanlite
- Lampa Trio Lighting
- Lampa Ranex
- Lampa Globo
- Lampa Paul Neuhaus
- Lampa Neewer
- Lampa Meross
- Lampa Artecta
- Lampa Xoro
- Lampa Laserworld
- Lampa Ozone
- Lampa Garden Lights
- Lampa Eufab
- Lampa Unilux
- Lampa Artemide
- Lampa Panzeri
- Lampa Honeycomb
- Lampa Elinchrom
- Lampa Auray
- Lampa Mission
- Lampa Paulmann
- Lampa Pixel
- Lampa GAO
- Lampa Wetelux
- Lampa Sagitter
- Lampa Esotec
- Lampa Neo
- Lampa Ozocozy
- Lampa Hatco
- Lampa DLG
- Lampa Goal Zero
- Lampa Lutec
- Lampa Ibiza Light
- Lampa Polarlite
- Lampa Lightway
- Lampa Broncolor
- Lampa NUVO
- Lampa Omnilux
- Lampa Digital Juice
- Lampa UMAGE
- Lampa Markslöjd
- Lampa Angler
- Lampa Luxform
- Lampa Velamp
- Lampa Lalumi
- Lampa ActiveJet
- Lampa Graypants
- Lampa Raya
- Lampa Rutec
- Lampa Luxo
- Lampa Kartell
- Lampa Rotolight
- Lampa Lightaccents
- Lampa SIGOR
- Lampa King Mungo
- Lampa DPM
- Lampa Maxim
- Lampa Oecolux
- Lampa Megatron
- Lampa Integral LED
- Lampa WiZ
- Lampa Casalux
- Lampa Briloner
- Lampa Frandsen
- Lampa Luctra
- Lampa Lowel
- Lampa Airam
- Lampa Lirio By Philips
- Lampa Westcott
- Lampa Gewiss
- Lampa SecoRüt
- Lampa Fabas Luce
- Lampa Dainolite
- Lampa Signature Design By Ashley
- Lampa Videx
- Lampa Louis Poulsen
- Lampa Fixpoint
- Lampa Kind LED
- Lampa ET2
- Lampa Quoizel
- Lampa Golden Lighting
- Lampa Ridem
- Lampa Fredrick Ramond
- Lampa Crystorama
- Lampa Sonneman
Najnowsze instrukcje dla Lampa
11 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024
9 Października 2024