Instrukcja obsługi Zvox SB500 Soundbar

Zvox głośnik SB500 Soundbar

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Zvox SB500 Soundbar (7 stron) w kategorii głośnik. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/7
Setup & Operation
ZVOX Audio Soundbars
Don’t Worry It’s Pretty Easy.
What’s In The Box
Soundbar • Remote control • Instruction sheets
AC power cord with integral power supply • Optical Digital and Analog signal cables
(866) 367-9869 | info@zvoxaudio.com
®
Position The System.
STEP 1
STEP 2
STEP 3
STEP 4
Connect One Signal Cable.
Connect the Power cable.
Use the Soundbar remote to
turn on power and adjust volume.
Home Theater
Made Simple!
Face Front Face Up Wall Mount
SB500 & SB400
6. Connecting a Powered Subwoofer to the Soundbar
The ZVOX Audio soundbar has a monaural Subwoofer Output (a single RCA jack). You can
connect this signal output to the input of a powered subwoofer for stronger and deeper
bass output than what is available from the soundbar alone. For best results, the powered
subwoofer should have both volume and low-pass adjustments. Low-pass sets the upper
frequency limit of the powered subwoofer.
15. Grounding or Polarization–This product may be
equipped with a polarized alternating-current line
plug (a plug having one blade wider than the other).
This plug will t into the power outlet only one way.
This is a safety feature. If you are unable to insert the
plug fully into the outlet, try reversing the plug. If the
plug should still fail to t, contact your electrician to
replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.
Alternate Warnings–This product is equipped with
a three-wire grounding-type plug, a plug having a
third (grounding) pin. This plug will only t into a
grounding-type power outlet. This is a safety feature.
If you are unable to insert the plug into the outlet,
contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the
grounding-type plug.
16. Ventilation–Slots and openings in the cabinet
are provided for ventilation and to ensure reliable
operation of the product and to protect it from
overheating, and these openings must not be
blocked or covered. The openings should never be
blocked by placing the product on a bed, sofa, rug,
or other similar surface. This product should not be
placed in a built-in installation such as a bookcase
or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
17. The MAINS plug or an appliance coupler is used as the
disconnect device, the disconnect device shall remain
readily operable.
18. CLASS II apparatus with double insulation, and no
protective earth provided.
19. CAUTION: Danger of explosion if the remote control
battery is incorrectly replaced. Replace only with the
same or equivalent type.
20. WARNING: The remote control battery (battery or
batteries or battery pack) shall not be exposed to
excessive heat such as sunshine, re or the like.
21. No naked ame sources, such as lighted candles,
should be placed on the apparatus.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not t into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specied by
the manufacturer.
12. Use only with the cart, stand, tripod,
bracket, or table specied by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Important Safety Instructions
READ THIS FIRST
Important Safety Instructions For ZVOX Audio System
CAUTION
RISK OF ELECTRICAL
SHOCK, DO NOT OPEN
Warning: To reduce
the risk of electrical
shock, do not remove
cover (or back) – no
serviceable parts
inside. Refer servicing
to qualied service
personnel.
This lightning ash with arrowhead
symbol, within an equilateral triangle, is
intended to alert the user to the presence
of uninsulated “dangerous voltage” within
the product’s enclosure that may be of
sufcient magnitude to constitute a risk
of electrical shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
TO PREVENT FIRE OR
SHOCK HAZARD, DO
NOT EXPOSE THIS
APPLIANCE TO RAIN
OR MOISTURE.
THIS APPLIANCE SHALL
NOT BE EXPOSED
TO DRIPPING OR
SPLASHING WATER
AND NO OBJECT
FILLED WITH LIQUIDS
SUCH AS VASES
SHALL BE PLACED
ON APPARATUS.
WARNING
Stable Placement. Do not place the
ZVOX system on an unstable cart,
stand, bracket or table. The ZVOX
system may fall, causing serious
injury to a child or adult and serious
damage to the product. Do not use
the ZVOX system on any unstable surface.
The soundbar has two keyhole-shaped mounting
locations on the back panel. These mounting sites
will securely hold a screwhead that is no larger
This document represents the conguration of specic ZVOX Audio products at the time of the document's creation. An actual ZVOX Audio
product's specications, features and other product attributes are subject to change or improvement without notice. All images used are for
illustrative purposes only. Before installing the product, please check your product for possible differences from the description in the manual.
Special Safety Warnings Regarding Placement
of the ZVOX System and Other Equipment
© 2017 ZVOX Audio LLC.
than 3/8" (10mm) in diameter. It is the installer’s
responsibility to conrm each mounting site used
to support the soundbar has an adequate weight-
handling margin to support both the weight of the
soundbar and extra weight that may inadvertently be
applied as a result of a house-hold accident. Damage
that may occur to the soundbar during or after the
mounting process or any other installation activity
is NOT covered under the terms of the ZVOX Audio
limited warranty.
STILL NEED ASSISTANCE? If your home TV system does not
conform to the descriptions in this guide, don’t hesitate to send an
inquiry to info@zvoxaudio.com or call ZVOX Audio at (866) 367-9869.
Please provide your TV brand and model number. A ZVOX Audio
representative should be available (Eastern Time Zone) 9:30 AM to
7:30 PM Monday through Friday.
Connect the Subwoofer Output on the soundbar to the powered subwoofer’s designated
monaural input.
Refer to Step 5 for a description of how to adjust the PS Menu on the Soundbar. Once the
powered subwoofer is connected to the soundbar, use the PS Menu on the soundbar to select
PS31. This stops the soundbar from playing deep bass, which can be produced by the powered
subwoofer. PS30 on the PS Menu restores deep bass output to the soundbar.
After setting the soundbar to PS31, the low-pass setting on the powered subwoofer should be set
to 85 Hz.
With the soundbar and powered subwoofer connected, the output level of the powered subwoofer
should be adjusted for best blend with the ZVOX Audio soundbar. A popular music recording with
consistent bass output is a good choice for this step.
For further information about the options provided by the PS menu, see the separate information
sheet Soundbar Adjustment Options, available online at ZVOX Audio's website.
7. Soundbar Wall Mounting Information
Dimensioned diagrams of each ZVOX Audio soundbar model can be found on
ZVOX Audio's website.
The soundbar has two keyhole mounting sites on its back panel. You can mount the
soundbar onto two screwheads using these mounting sites. A ZVOX Audio soundbar weighs
between 15 and 20 pounds. NOTE: It is the installer’s responsibility to ensure the screws are
installed into the wall or other surface securely and that the screwheads are the correct size
for the hanger mounts on the rear of the soundbar. ZVOX Audio recommends your mounting
sites be able to support at least twice the weight of the soundbar.
1. Speaker Placement
You can place the soundbar on any at, stable surface near your TV.
There are three general placement options, illustrated above:
Face Front You can place the soundbar on a at surface so it faces forward. This
placement is ideal for a shelf below, above or near the television.
Face Up You can place the soundbar facing up—often in front of the television. The
bottom of the soundbar should face the listening area. Check to ensure
the soundbar does not block the television infrared remote sensor. There
should be no shelf or at surface immediately above the soundbar in this
conguration.
Wall Mount The soundbar has two sturdy keyhole-shaped hanger mounts on the back
panel. You can hang the soundbar on two screwheads that are securely
installed in a wall or other vertical surface.
• If you have a powered subwoofer you wish to use with this soundbar, the subwoofer
connection guide is located on the last panel of this document.
• Consider the nish of the surface that will support the soundbar. It is the soundbar owner's
responsibility to insure that a surface nish that contacts the soundbar is protected,
should this be a concern of the soundbar owner. The contact area on the soundbar is
made of inert synthetic materials that typically do not react with furniture or wall nishes. But
any wall or surface nish can be altered by having any heavy object resting on it for a long
period of time. Place an appropriate barrier between any surface and the soundbar if you
are concerned about the nish of the supporting surface.
• A safe, secure installation is the soundbar owner’s responsibility.
• Use an unswitched AC outlet to provide power to the soundbar. With the soundbar's Auto
Standby feature turned on, the soundbar enters its low-power draw standby state after 20 to
30 minutes of inactivity. A soundbar uses less than 0.5 watt in Standby. Using a switched AC
outlet to cut off AC power to a soundbar system is not recommended. It delays subsequent
turn-on.
• Do not place any objects on top of a soundbar.
2. Connect Your TV's Audio Output to the Soundbar
All current TVs have an audio output. It is likely that one of the cables provided with the
soundbar can be used to connect the TV audio output to an input on the soundbar. DO NOT
disconnect any video program source connected to your TV (like a cable or satellite set top box,
DVD/Bluray or similar).
2
Connect the
Soundbar
to your TV.
3
Learn the
features of the
Soundbar.
4
“Teach” the
Soundbar your
preferred remote.
1
Place or
hang the
Soundbar.
Face UpFace Front Wall Mount
Optical Digital Audio Output Jack (see above image)
Most HDTVs have an optical digital audio output jack. Use the provided optical cable to connect
the TV’s output jack to optical input 1 on the soundbar.
Simple Setup – Just Four Steps
DIGITAL
AUDIO
OUT
HDMI 1 HDMI 2
VIDEO
Optical Digital
Audio Input
TV
Optical
Output
Optical Cable
Soundbar
Input
Panel
4b. End Panel Controls on the Soundbar
On the viewer’s right end of the soundbar are four buttons.
A) POWER button:
This button turns the soundbar “ON” if it is in Standby. If this button is pressed briey while the
soundbar is “ON”, it will mute and unmute the soundbar. To turn off the soundbar, press and
hold down this button for about ve seconds.
B) Volume Up/Down rocker button
Adjusts volume up and down. Pressing either side of this button will “unmute” the speaker if it is
muted.
C) Input button:
A brief press and release of the INPUT button selects the next input in sequence.
5. Tonal Prole Setting
The soundbar has three selectable tonal proles that allow it to better match the acoustics of its
room position. Use the soundbar's PS menu feature to choose one of these three settings.
Face Front ........ PS16 - on a at surface, facing front.
Face Up ............ PS17 - on a at surface, facing up.
Wall Mount ....... PS18 - on a vertical surface, facing into the room.
The default setting for the soundbar is Face Front.
If your soundbar’s position is Face Up or Wall Mount, you should select PS17 or PS18 from the
PS menu.
PS Menu: You adjust the PS Menu setting by rst pressing down on two buttons on the end
panel of the soundbar: Power ( ) and Volume Up (+). After about ve to seven seconds you
should see PS start ashing on the soundbar's display. The rst time you bring up the PS menu,
it should show “PS 0”.
Once you see the PS display, release the buttons. Then press and release the Volume Up button
to increase the PS number. Continue pressing and releasing the Volume Up button until you
reach the setting you want: PS16, PS17 or PS18.
If your home TV system does not match the descriptions in this
guide, don’t hesitate to send an inquiry to info@zvoxaudio.com
or call ZVOX Audio at (866) 367-9869. Please provide your TV
brand and model number. A ZVOX Audio representative should be
available (Eastern Time Zone) 9:30 AM to 7:30 PM Monday through
Friday and 10:30 AM to 5:30 PM on Saturday.
A
B
C

Specyfikacje produktu

Marka: Zvox
Kategoria: głośnik
Model: SB500 Soundbar

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Zvox SB500 Soundbar, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje głośnik Zvox

Zvox

Zvox SB400 Soundbar Instrukcja

26 Września 2024
Zvox

Zvox AccuVoice AV200 Instrukcja

26 Września 2024
Zvox

Zvox SoundBase 440 Instrukcja

26 Września 2024
Zvox

Zvox ACCUVOICE AV203 Instrukcja

26 Września 2024
Zvox

Zvox SB380 SoundBar Instrukcja

26 Września 2024
Zvox

Zvox Z-Base 555 Instrukcja

26 Września 2024
Zvox

Zvox AccuVoice AV155 Instrukcja

25 Września 2024
Zvox

Zvox SB500 Soundbar Instrukcja

25 Września 2024

Instrukcje głośnik

Najnowsze instrukcje dla głośnik

Teufel

Teufel Rockster Air Instrukcja

15 Października 2024
Alpine

Alpine PSS-22WRA Instrukcja

15 Października 2024
Bauhn

Bauhn APPS-0724 Instrukcja

15 Października 2024
Aiwa

Aiwa SP-A100 Instrukcja

15 Października 2024
Harman Kardon

Harman Kardon Citation One Instrukcja

14 Października 2024
Alpine

Alpine 30MC Instrukcja

14 Października 2024
Magnat

Magnat Needle 9000 ALU Instrukcja

14 Października 2024
Pioneer

Pioneer SP-T22A-LR Instrukcja

14 Października 2024
Sharp

Sharp PS-932 Instrukcja

14 Października 2024
Pyle

Pyle PDWR64BTW Instrukcja

13 Października 2024