Instrukcja obsługi Zoeller 131

Zoeller Przepych 131

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Zoeller 131 (8 stron) w kategorii Przepych. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

DRAIN PUMP SYSTEMS

MODELS 104*, 105, 110, 115, 120, 131

INSTALLATION INSTRUCTIONS

PREINSTALLATION CHECKLIST

P/N 017583

SECTION: 6.10.045

FM2336

1113

Supersedes

0612

Notice to Installer: Instructions must remain with installation.

MODEL: ______________________

DATE CODE: __________________

DATE INSTALLED: _____________

1. Inspect your unit. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before using. remove the test DO NOT

plugs from the pump.

2. Carefully read the literature provided to familiarize yourself with specic details regarding installation and use. These materials should be retained for future reference.

1. To reduce the risk of electrical shock, a properly grounded receptacle of grounding

type must be installed and protected by a ground fault circuit interrupter (GFCI)

and in accordance with National Electrical Code and local codes.

(SEE WARNING BELOW)

2. Make certain that the receptacle is within the reach of the pump’s power

supply cord. DO NOT USE AN EXTENSION CORD. Extension cords that

are too long or too light do not deliver sufcient voltage to the pump motor.

But more important, they could present a safety hazard if the insulation were

to become damaged or the connection end were to fall into the sump.

3. Testing for Ground. As a safety measure, each electrical outlet should be

checked for ground using an Underwriters Laboratory Listed circuit analyzer

which will indicate if the power, neutral and ground wires are correctly connected

to your outlet. If they are not, call a qualied electrician.

4. For Added Safety. Pump must be connected to a 3-prong grounded outlet

interrupter device (ground fault circuit interrupter).

5. FOR YOUR PROTECTION, ALWAYS DISCONNECT PUMP FROM ITS

POWER SOURCE BEFORE HANDLING. Single phase pumps are supplied

with a 3-prong grounded plug to help protect you against the possibility of

electrical shock. DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE

GROUND PIN. To reduce the risk of electrical shock, a properly grounded

receptacle of grounding type must be installed and protected by a ground

fault circuit interrupter (GFCI) in accordance with national electrical code and

local codes.

6. Installation and checking of electrical circuits and hardware should only be

performed by a qualied licensed electrician.

7. Risk of electric shock - These pumps have not been investigated for use in

swimming pool areas.

8. According to the state of California (Prop 65), this product contains chemicals

known to the state of California to cause cancer and birth defects or other

reproductive harm.

1. Check to be sure your power source is adequate for handling the voltage

requirements of the motor, as indicated on the pump or basin plate.

2. Make sure the pump electrical supply circuit is equipped with fuses or circuit

breakers of proper capacity. A separate branch circuit is recommended, sized

according to the National Electrical Code for the current shown on the pump

name plate.

3. All plumbing (discharge and vent lines) must be installed to meet local codes.

Unit must be vented. DO NOT USE AN AUTOMATIC PLUMBING VENT

DEVICE SIMILAR TO A "PRO-VENT". Some states require this product to

be installed by a licensed plumber.

4. Repair and service should be performed by Zoeller Pump Company Authorized

Service Station only.

5. CHECK VALVE MUST BE USED TO REDUCE UNNECESSARY CYCLING

OF PUMP. Check valve must be purchased separately on model 104 only.

6. Dewatering pumps are not designed or intended for handling raw sewage.

7. Maximum operating temperature for 105-131 Drain Pumps must not exceed

130°F (54°C). 104 Drain Pumps are not to exceed 110°F (43°C).

8. For health reasons, do not unplug, turn off, or disable pump and use pump

tank system as a way to ll up a sink or laundry tray, etc.

9. Unit is designed for above ground installation only.

SEE BELOW FOR LIST OF WARNINGS

CAUTION

SEE BELOW FOR LIST OF CAUTIONS

* MODEL 104 IS NOT

IAPMO APPROVED.

UPC

COMPLIES WITH ASME A112.3.4

and CSA B45.9

REFER TO WARRANTY ON PAGE 2.

Pumps with the “UL” mark and pumps with the “US” mark are tested to

UL Standard UL778. CSA Certified pumps are certified to CSA Standard

C22.2 No. 108.

Product information presented

here reects conditions at time

of publication. Consult factory

regarding discrepancies or

inconsistencies.

MAIL TO: P.O. BOX 16347 • Louisville, KY 40256-0347

SHIP TO: 3649 Cane Run Road • Louisville, KY 40211-1961

(502) 778-2731 • 1 (800) 928-PUMP • FAX (502) 774-3624

visit our web site:

www.zoeller.com

Your Peace of Mind is Our Top Priority

Manufacturer warrants, to the purchaser and subsequent owner during

the warranty period, every new product to be free from defects in material

and workmanship under normal use and service, when properly used and

maintained, for a period of one year from date of purchase by the end user, or

18 months from date of original manufacture of the product, whichever comes

rst. Parts that fail within the warranty period, one year from date of purchase

by the end user, or 18 months from the date of original manufacture of the

product, whichever comes rst, that inspections determine to be defective

in material or workmanship, will be repaired, replaced or remanufactured

at Manufacturer's option, provided however, that by so doing we will not be

obligated to replace an entire assembly, the entire mechanism or the complete

unit. No allowance will be made for shipping charges, damages, labor or

other charges that may occur due to product failure, repair or replacement.

This warranty does not apply to and there shall be no warranty for any material

or product that has been disassembled without prior approval of Manufacturer,

subjected to misuse, misapplication, neglect, alteration, accident or act of

God; that has not been installed, operated or maintained in accordance with

Manufacturer's installation instructions; that has been exposed to outside

substances including but not limited to the following: sand, gravel, cement,

mud, tar, hydrocarbons, hydrocarbon derivatives (oil, gasoline, solvents,

etc.), or other abrasive or corrosive substances, wash towels or feminine

sanitary products, etc. in all pumping applications. The warranty set out in

the paragraph above is in lieu of all other warranties expressed or implied;

and we do not authorize any representative or other person to assume for us

any other liability in connection with our products.

Contact Manufacturer at, 3649 Cane Run Road, Louisville, Kentucky 40211,

Attention: Customer Support Department to obtain any needed repair or

replacement of part(s) or additional information pertaining to our warranty.

MANUFACTURER EXPRESSLY DISCLAIMS LIABILITY FOR SPECIAL,

CONSEQUENTIAL OR INCIDENTAL DAMAGES OR BREACH

OF EXPRESSED OR IMPLIED WARRANTY; AND ANY IMPLIED

WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE AND OF

MERCHANTABILITY SHALL BE LIMITED TO THE DURATION OF THE

EXPRESSED WARRANTY.

Some states do not allow limitations on the duration of an implied warranty,

so the above limitation may not apply to you. Some states do not allow the

exclusion or limitation of incidental or consequential damages, so the above

limitation or exclusion may not apply to you.

This warranty gives you specic legal rights and you may also have other

rights which vary from state to state.

Limited Warranty

ELECTRICAL PRECAUTIONS- Before servicing a pump, always shut off the main power breaker and then unplug the pump - making

sure you are not standing in water and wearing insulated protective sole shoes. Under ooded conditions, contact your local electric company or a

qualied licensed electrician for disconnecting electrical service prior to pump removal.

Submersible pumps can become pressurized under normal operating conditions — allow 2½ hours after disconnecting before attempting service.

CONDITION

A. Pump will not start or run.

B. Motor overheats and trips overload

or blows fuse.

C. Pump starts and stops too often.

D. Pump will not shut off.

E. Pump operates but delivers little

or no water.

F. Drop in head and/or capacity after

a period of use.

G. Iftankorttingsleak.

If the above checklist does not uncover the problem, consult the factory - Do not attempt to service or otherwise disassemble pump. Service must

be by a Zoeller Authorized Service Station.

Service Checklist

COMMON CAUSES

Check fuse, low voltage, overload open, open or incorrect wiring, open switch, impeller or seal bound mechanically,

defective capacitor or relay when used, motor or wiring shorted. Float assembly held down. Switch defective,

damaged, or out of adjustment.

Incorrect voltage, negative head (discharge open lower than normal) impeller or seal bound mechanically, defective

capacitor or relay, motor shorted.

Float too tight on rod, check valve stuck, or none installed in long distance line, overload open, switch

defective.

Debris under oat assembly, oat or oat rod bound by basin sides or other, switch defective, damaged or out of adjustment.

Check strainer housing, discharge pipe, or if check valve is used, the vent hole must be clear. Discharge head

exceeds pump capacity. Low or incorrect voltage. Incorrect motor rotation. Capacitor defective. Incoming water

containing air or causing air to enter pumping chamber.

Increased pipe friction, clogged line or check valve. Abrasive material and adverse chemicals could possibly

deteriorate impeller and pump housing. Check line. Remove base and inspect.

Carefully tighten pipe joints (use pipe dope) and screws. Check gasket location, tighten lid evenly. Do not over

tighten ttings or screws.

1. Read all instructions before beginning installation.

2. Be certain that basin is on a rm level surface.

3. Do not use an automatic plumbing vent device.

4. Do not over-torque lid attachment screws.

5. Always use a check valve on the discharge line.

6. Test operation of pump per STEP 6.

Ten Helpful Hints For Easy Installation

Performance Characteristics

7. Always provide some means to disconnect basin from plumbing for

maintenance purposes.

8. Run unit at least once a month to verify proper operation.

9. The model number and date code can be found on the lid warning label.

10. Plug pump into a properly grounded GFCI receptacle.

009898

Meters

20 6.1

Shut-off Head:

15 4.6

10 3.0

5 1.5

Feet

MODELS

Liters

273

231

170

19.25 ft. (5.9m)

9525

23 ft. (7.0m)

129

163

Gal.

104/132

Liters Gal. Liters Gal.

131

105/110

115/120

18 ft. (5.5m)

144

114

-- --

2010

GALLONS

LITERS

504030

80 160

FLOW PER MINUTE

105/110/

8060 70

240

131

PUMP PERFORMANCE CURVE

104/105/110/115/120/131/132

TOTAL DYNAMIC HEAD

620

FEET

METERS

115/120

104/132

1. DO read all installation material included with the pump.

2. DO inspect unit for any visible damage caused by shipping. Contact

dealer if unit appears to be damaged.

3. DO clean all debris from the basin and pump.

4. DO always disconnect pump from power source before handling.

DO always connect to a separately protected and properly grounded

ground fault protected circuit. DO NOT ever cut, splice or damage

power cord. DO NOT carry or lift pump by its power cord. DO NOT use

an extension cord.

Do’s And Don't’s For Installing A Unit

5. DO NOT use a discharge pipe smaller than the pump discharge size.

6. DO test pump immediately after installation to be sure that the system

is working properly.

7. DO review all applicable local and national codes and verify that the

installation conforms to each of them.

8. DO NOT install unit in the ground.

Specyfikacje produktu

Marka:	Zoeller
Kategoria:	Przepych
Model:	131

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Zoeller 131, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Przepych Zoeller

Zoeller 131 Instrukcja

27 Marca 2025

Zoeller M282 Instrukcja

27 Marca 2025

Zoeller M98 Instrukcja

25 Września 2024

Zoeller M267 Instrukcja

25 Września 2024

Zoeller Aquanot Fit 508 Instrukcja

25 Września 2024

Instrukcje Przepych

Najnowsze instrukcje dla Przepych

Lezyne CNC Travel Floor Drive Instrukcja

29 Marca 2025

Lezyne Shock Digital Drive Instrukcja

29 Marca 2025

Lezyne Gauge Drive HP Instrukcja

29 Marca 2025

Lezyne Micro Floor Drive XL Instrukcja

29 Marca 2025

Lezyne Gauge Drive HV Instrukcja

29 Marca 2025

Comet IDS 1400 Instrukcja

29 Marca 2025

Comet APS 41 Instrukcja

29 Marca 2025

Comet IDS 2200 Instrukcja

29 Marca 2025

Comet IDS 1000 Instrukcja

29 Marca 2025

Comet IDS 2600 Instrukcja

29 Marca 2025