Instrukcja obsługi WyreStorm TX-70-POH

WyreStorm przedłużacz AV TX-70-POH

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WyreStorm TX-70-POH (4 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

4K HDMI over HDBaseT Transmitter

with PoH | Bi-directional IR & RS-232 (70m/230ft)

TX-70-POH Quickstart Guide

In the Box

1x TX-70-POH Transmitter

1x 2-pin Screw Down Phoenix Connector

1x 3-pin Screw Down Phoenix Connector

1x IR Emitter

1x Broadband IR Receiver (30KHz~50KHz)

2x Mounting Brackets

1x Quickstart Guide (this document)

Basic Wiring Diagram

Key HDMI/Digital Video HDBaseT/Ethernet

TX-70-POH

IR TX to IR Loop

(Required for remote source control)

MX-0808-PP-POH-CUSTOM with TX-POH-100

UHD Source

IMPORTANT!

Do not connect or disconnect (hot plug) the HDMI, or HDBaseT

connections while the transmitter or receiver is powered on. Doing so

may cause damage to the units or connected devices.

Additional Information

This Quickstart Guide provides the basic steps for the common uses of

this product. Refer to the Installation Guide and other documentation on

the product page for additional information.

Recommended Products

To take full advantage of the features of this receiver, WyreStorm

recommends the following products be used within the system.

• HDBaseT Matrix Switchers with HDBT In

The TX-70-POH was designed to be work with the HDBT In found on

some WyreStorm matrixes to allow remote devices to be used as a

source.

• MX-0808/1616-PP-POH-CUSTOM with TX-POH-100

• SW-1001-HDBT

• Cable for Connecting to IR Connecting Blocks/Control Systems

When connecting the IR RX to an IR connecting block or control

system, use the cable to remove the sleeve WyreStorm CAB-IR-LINK

+5V DC supplied by the IR Ext/IR RX ports.

Before Beginning

• WyreStorm recommends visiting the product page before installing

this product for updates to this Quickstart Guide as well as other

information about the product.

• Verify that all items are included in the packaging per the In The Box

list.

Pre Wire

1. Run a Cat5e/6/6a cable from the transmitter location to the matrix/

receiver location. See for resolution Supported Video Resolutions

distance restrictions. Terminate the cable per the HDMI/HDBaseT

Wiring section.

2. (Optional) If using 3rd party IR emitters or connecting blocks, run

the wire and terminate per the section.IR TX (Emitter) Wiring

3. (Optional) If using 3rd party IR receivers, run the wire and terminate

per the section.IR RX (Receiver) Wiring

4. (Optional) If using RS-232 pass-through, run the wire and terminate

per the section.RS-232 Wiring

Transmitter Installation

1. Install the matrix/receiver following the documentation provided

with the product.

2. Connect an HDMI source to the on the transmitter using HDMI In

an HDMI cable from a high quality brand such as WyreStorm

Express.

3. Using the cable created in Pre Wire step 1, connect the 8-pin RJ-45

female plug to the jack.HDBT In

4. (Optional) Using the included IR emitter or the cable created in

Pre Wire step 2, place an IR emitter onto a source device near the

device’s IR sensor. Connect the 3.5mm (1/8in) Mono Plug to an IR

TX port.

5. (Optional) Using an included IR receiver, connect the 3.5mm (1/8in)

Stereo Plug to an port. If using a control system, use the IR Ext

WyreStorm CAB-IR-LINK Pre Wire or the cable created in step 3.

6. (Optional) If using RS-232 pass-through, connect the 3-pin

connector to the port on the receiver and the opposite end RS-232

to a port on the device being controlled.

TX-70-POH Quickstart Guide | 151124

North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

PoH-Compatible HDBaseT transmitter to send HD Video & Audio 70m/230ft over HDBaseT.

Front Panel

Rear Panel

Power In 5.5mm Male Barrel Jack

Connection to this jack is not required when using PoH. See Power Supply Wiring.

HDBT Out 8-pin RJ-45 female

Connect to the of a matrix or HDBaseT transmitter.HDBT Out

HDMI In 19-pin type A HDMI female:

Supports HDMI and DVI/D (requires adapter-not included).

IR TX/RX

IR TX - 3.5mm (1/8in) Mono Jack:

Connect to the supplied IR emitter to control a local device from the remote display location via HDBaseT.

IR RX - 3.5mm (1/8in) Stereo Jack:

Connect to the supplied IR receiver to send IR to the remote display via HDBaseT.

See IR Wiring.

RS-232

3-pin Screw Down Phoenix Connector

Used to send and receive RS-232 signals to/from the source location via HDBaseT and rmware updates. See RS-232

Wiring.

RS-232 Mode

Switches the mode for the RS-232 port.

Normal: RS-232 HDBaseT pass-through.

Update: RS-232 rmware update.

Power LED Solid: The transmitter is powered On

Off: The transmitter is powered Off

Status LED Flashing: The transmitter is operating normally.

Off: The transmitter is Not operating normally.

HDCP LED

Solid: Audio and Video signal is HDCP protected.

Flashing: Audio and Video signal is not HDCP protected.

Off: No Audio and Video signal.

LINK LED Solid: Link to receiver has been established

Flashing: Link to receiver has not been established

A B C D E

TX-70-POH Quickstart Guide | 151124

North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343

support@wyrestorm.com

2 of 4

HDMI/HDBaseT Wiring

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables,

and electrical or environmental interference can have an adverse

effect on HDMI or HDBaseT transmission limiting performance. Steps

should be taken to minimize these factors (or remove completely)

during installation for best results.

• While similar in nature, the HDBaseT protocol is different than Ethernet

and voltages provided for PoH can be higher than those provided by

PoE. For this reason, never connect an HDBaseT link to an Ethernet

router or switch to avoid damaging the connected devices.

Wiring for HDBaseT follows the EIA T568B standard.

Pin 1

Pin 8

Wire colors shown follow EIA/TIA-568B standard.

Pin 1:

Pin 2:

Pin 3:

Pin 4:

Pin 5:

Pin 6:

Pin 7:

Pin 8:

White/Orange

Orange

White/Green

Blue

White/Blue

Green

White/Brown

Brown

Supported Video Resolutions

The type of category cable used and the distance between the

transmitter and receiver can restrict the available video resolution.

Cable Type Range Supported Resolution

Cat5/5e/6

70m/230ft 1080p@60Hz 48bit

35m/115ft 1080p@60Hz 3D

4K@60Hz 4:2:0 24bit

Cat6a 100m/328ft 1080p@60Hz 48bit

1080p@60Hz 3D

IR Wiring

IR TX (Emitter) Wiring

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: IR Signal

Sleeve: Ground (GND)

IR RX (Receiver) Wiring

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that

outputs +5V DC to power the included IR receiver.

IMPORTANT! IR TX Connection Guidelines

3rd party IR receivers may require a different voltage, refer to the

documentation provided with the IR receiver before making any

connections to avoid damaging the device.

When connecting to an IR control system use the WyreStorm CAB-IR-

LINK cable to remove the sleeve +5V DC.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

RS-232 Connection Guidelines

The following wiring diagram shows the pinouts for the extender set.

While not shown, connect the TX (transmit) to RX (receive) pins at the

control system or PC side of the cable.

Most control systems and computers are DTE where pin 2 is RX, this can

vary from device to device. Refer to the documentation for the connected

device for pin functionally to ensure that the correct connections can be

made.

Wire colors shown follow EIA-561 standard.

Pin 1:

Pin 2:

TX (Transmit)

RX (Receive)

Pin 3: Ground (GND)

1 2 3

Power Supply Wiring

The TX-70-POH can receive power via PoH from a compatible HDBaseT

matrix. Should the distance or other factors prevent PoH from being

used, connect a 12V DC 1A power supply (sold separately) to the

receiver.

TX-70-POH Quickstart Guide | 151124

North America: 518-289-1294 | EMEA/ROW: 44 (0) 1793 230 343

support@wyrestorm.com

3 of 4

Specyfikacje produktu

Marka:	WyreStorm
Kategoria:	przedłużacz AV
Model:	TX-70-POH
Kolor produktu:	Czarny
Częstotliwość wejściowa AC:	50 - 60 Hz
Napięcie wejściowe AC:	100 - 240 V
Wysokość produktu:	18 mm
Szerokość produktu:	181.7 mm
Głębokość produktu:	94 mm
Waga produktu:	400 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Technologia łączności:	Przewodowa
Certyfikaty:	CE, FCC
Maksymalne zużycie mocy:	7.2 W
Zakres temperatur (eksploatacja):	0 - 45 °C
Zakres wilgotności względnej:	10 - 90 %
Rozdzielczość:	4096 x 2160 px
Obsługiwane formaty audio:	PCM
Kompatybilność 3D:	Tak
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-20 - 70 °C
Model:	Nadajnik AV
Prąd wyjściowy:	2 A
Maks. rozdzielczość:	4096 x 2160 px
HDCP:	Tak
Aktualizacje oprogramowania urządzenia:	Tak
Maksymalny dystans transferu:	70 m
Obsługiwane rozdzielczości grafiki:	1920 x 1080 (HD 1080),3840 x 2160,4096 x 2160
HDMI in:	1
Zdalne wejście IR:	1
Obsługiwane tryby wideo:	1080p
Zdanlne wyjścia IR:	1
Obsługiwane typy kabli:	Cat6, Cat6a, Cat7
Wyjścia RJ-45:	1
Obsługa Consumer Electronics Control (CEC):	Tak
Interfejs do nagrywania wideo:	1
Port HDBaseT:	Tak
Certyfikat HDBaseT:	Tak