Instrukcja obsługi WyreStorm RXV-35-4K

WyreStorm przedłużacz AV RXV-35-4K

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WyreStorm RXV-35-4K (4 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

4K HDR HDMI-Over-HDBaseT Receiver

with HDCP 2.2 and PoH

RXV-35-4K v1 Quickstart Guide

RXV-35-4K v1 Quickstart Guide | 190501

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x RXV-35-4K Receiver

1x IR Emitter

1x IR Receiver

2x Mounting Brackets

1x 3-pin Terminal Block

1x Quickstart Guide (this document)

HDMI to display

IR TXIR RX

RXV-35-4K (Receiver)

HDMI to display

IR TXIR RX

HDMI from source

LAN Cat6a/7

C Mains

ower

Cat6a/7

Blu-r

y Pl

RXV-35-4K (Receiver)

Matrix Control Only

Control System

CAB-IR-LINK (Sold Separately)

Wireless Router

M -0808-H2A (Matrix)XV

Receivers

KEY

HDMI

HDBaseT / Ethernet

Control

Power

Digital Audio

RXV-35-4K v1 Quickstart Guide | 190501

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

Front Panel Rear Panel

Power LED Solid: The receiver is powered On

Off: The receiver is powered Off

Status LED Flashing: The receiver is operating normally.

Off: The receiver is Not operating normally.

HDCP LED

Solid: HDCP content is present.

Flashing: HDCP content is not present.

Off: No signal.

LINK LED

Solid: Link to receiver has been established.

Flashing: Link to receiver has not been

established.

Power Input

5.5mm Screw Down Barrel Jack

Connect to the included 18V DC 1A power

supply to the transmitter or receiver. A power

supply is not required on the other end as it

will be powered using PoH.

HDBT In

HDBT Out

8-pin RJ-45 female

Connect the matrix HDBT Out to

receivers HDBT In.

IR TX

IR RX

IR TX - 3.5mm (1/8in) Mono Jack: Connect

to the supplied IR emitter to control a local

device from the remote display location via

HDBaseT.

IR RX - 3.5mm (1/8in) Stereo Jack: Connect

to the supplied IR receiver to send IR to the

remote display location via HDBaseT.

See for more IR TX/RX Guidelines

information.

RS-232 1x RS-232: 3-pin Terminal Block

HDMI In

HDMI Out

19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

A CB D A CB D E

RXV-35-4K v1 Quickstart Guide | 190501

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends the use of shielded category cable to minimize

signal noise and interference.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received by the NetworkHD

system. Other 3rd party emitters and receivers can be used; however, these

devices must operate in the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a NetworkHD system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within the

port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

RS-232 Wiring

The RXV-35-4K uses a 3-pin RS-232 with no hardware ow control. Most

control systems and computers are DTE where pin 2 is RX, this can vary

from device to device. Refer to the documentation for the connected device

for pin functionally to ensure that the correct connections can be made.

3rd Party Device

Pin 1 TX (Transmit) > To > RX (Receive)--- ---

Pin 2 RX (Receive) > To > TX (Transmit)--- ---

Pin 3 G (Gro d) > To > G (Gro d)un --- --- un

WyreStorm Co ectornn

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device

• Verify that all HDMI and HDBaseT connections are not loose and are

functioning properly

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard

• Verify that the output resolution of the source and display is supported by

this matrix and recevier.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR and RS-232 cables are properly terminated following the

Wiring and Connections section.

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

Specyfikacje produktu

Marka:	WyreStorm
Kategoria:	przedłużacz AV
Model:	RXV-35-4K
Kolor produktu:	Czarny
Wysokość produktu:	15.2 mm
Szerokość produktu:	136 mm
Głębokość produktu:	74.2 mm
Waga produktu:	240 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Technologia łączności:	Przewodowa
Maksymalne zużycie mocy:	12.42 W
Zakres temperatur (eksploatacja):	0 - 45 °C
Zakres wilgotności względnej:	10 - 90 %
Kanały wyjścia audio:	5.1 kan.
Przewodowa sieć LAN:	Tak
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-20 - 70 °C
Dopuszczalna wilgotność względna:	10 - 90 %
Model:	Amplituner
Maks. rozdzielczość:	4096 x 2160 px
Maksymalna częstotliwość odświeżania:	60 Hz
Wersja HDMI:	2.0
HDCP:	Tak
Szerokość pasma:	9.2 Gbit/s
Możliwości montowania w stelażu:	Tak
System dźwięku:	Wielokanałowy
Maksymalny dystans transferu:	70 m
Obsługiwane tryby wideo:	1080p, 2160p
Wersja HDCP:	2.2
Wejśćie 3,5 mm:	Tak
Obsługiwane typy kabli:	Cat6, Cat6a, Cat7, HDMI
Wejścia RJ-45:	1
Porty wejściowe RS-232:	1
Obsługa Consumer Electronics Control (CEC):	Tak
Port HDBaseT:	Tak
Rozszerzone dane identyfikacyjne wyświetlacza (EDID):	Tak
Certyfikat HDBaseT:	Tak