Instrukcja obsługi WyreStorm RXV-70-4K

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WyreStorm RXV-70-4K (4 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/4
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
RXV-70-4K Quickstart Guide | 180917
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
1 of 4
WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features before beginning the
installation process.
Basic Wiring Diagram
Quickstart Guide
RXV-70-4K
4K HDR HDMI-Over-HDBaseT Receiver
with HDCP 2.2 and PoH
HDBaseT Cat6/6a/7
Control
Power
Key
HDMI/Digital Video
HDBaseT/Ethernet
MX-1616-H2XC
with TX-H2X-VLC
Modular Card
Control System
IR RX
CAB-IR-LINK (Sold Separately)
RXV-70-4K
HDR Display
HDMI
Ethernet
IR RX IR TX
Note: Not required if powering
the receiver via PoH.
12V DC 2A
Power Supply
IMPORTANT! Installation Requirements
Visit the product page to download the latest rmware, document version,
additional documentation, and conguration tools.
Read through the section for important wiring Wiring and Connections
guidelines before creating or choosing premade cables.
While this product supports CEC, WyreStorm cannot guarantee
compatibility with all forms of CEC communication.
In the Box
1x RXV-70-4K Receiver
1x IR Emitter
1x IR Receiver
2x Mounting Brackets
1x 3-pin Phoenix Connector
1x Quickstart Guide (this document)
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
RXV-70-4K Quickstart Guide | 180917
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
2 of 4
Wiring and Connections
WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in its
entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.
IMPORTANT! Wiring Guidelines
The use of patch panels, wall plates, cable extenders, kinks in cables, and
electrical or environmental interference will have an adverse effect on
signal transmission which may limit performance. Steps should be taken
to minimize or remove these factors completely during installation for best
results
WyreStorm recommends using pre-terminated HDMI and DP cables due to
the complexity of these connector types. Using pre-terminated cables will
ensure that these connections are accurate and will not interfere with the
performance of the product.
IR TX/RX Guidelines
Using WyreStorm infrared emitters and receivers is the best way to ensure
that most IR coding formats are transmitted and received Other 3rd party
emitters and receivers can be used; however, these devices must operate in
the same manner as the WyreStorm devices.
Due to differences in IR across 3rd party control systems their IR ports
should never be connected directly to a NetworkHD system as an
incompatibility may exist. WyreStorm offers a cable that compensates for
voltage differences as well adjusts for differences in the pins used within
the port. Refer to the product page for more information.CAB-IR-LINK
IR TX Port Pinout
Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.
IR RX Port Pinout
Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs
+5V DC to power the included IR receiver.
RS-232 Wiring
The RXV-70-4K uses a 3-pin RS-232 with no hardware ow control. Most
control systems and computers are DTE where pin 2 is RX, this can vary
from device to device. Refer to the documentation for the connected device
for pin functionally to ensure that the correct connections can be made.
3rd Party Device
Pin 1 TX (Transmit) > To > RX (Receive)--- ---
Pin 2 RX (Receive) > To > TX (Transmit)--- ---
Pin 3 G (Gro d) > To > G (Gro d)un --- --- un
WyreStorm Co ectornn
Copyright © 2018 WyreStorm Technologies | wyrestorm.com
RXV-70-4K Quickstart Guide | 180917
UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)
support@wyrestorm.com
3 of 4
EDID Conguration
This receiver uses EDID pass-through from the display to the source. No conguration is required for EDID settings.
Setup and Conguration
RS-232 Mode Settings
The RS-232 connector is used to transmit RS-232 over HDBaseT to the remote
location and for rmware updates. Ensure that the RS-232 Mode switch in
the proper position for the operation being performed. This connection is only
available on version 1 of this product.
Set the mode switch to to transmit RS-232 Normal
signals from the TX to the RX for controlling devices in
the remote location.
Set the mode switch to the position to install a Update
rmware update in either the TX or RX.
Troubleshooting
No or Poor-Quality Picture (snow or noisy image)
Verify that power is being supplied to the transmitter and receiver.
Verify that the ber cable is properly terminated.
Verify that the output resolution of the source and display is supported by
this extender.
If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.
Verify that all source and HDBaseT connections are not loose and are
functioning properly.
No or Intermittent 3rd party Device Control
Verify that the RS-232/Ethernet cables are properly terminated.
Verify that emitters/receivers are compatible with WyreStorm IR.
If using an IR control system, verify that it is connected using the CAB-IR-
LINK cable.

Specyfikacje produktu

Marka: WyreStorm
Kategoria: przedłużacz AV
Model: RXV-70-4K
Kolor produktu: Czarny
Wysokość produktu: 20 mm
Szerokość produktu: 150 mm
Głębokość produktu: 74.4 mm
Waga produktu: 400 g
Certyfikat środowiskowy (zrównoważonego rozwoju): RoHS
Technologia łączności: Przewodowa
Maksymalne zużycie mocy: 8.68 W
Zakres temperatur (eksploatacja): 0 - 45 °C
Zakres wilgotności względnej: 10 - 90 %
Kanały wyjścia audio: 5.1 kan.
Przewodowa sieć LAN: Tak
Diody LED: Tak
Zakres temperatur (przechowywanie): -20 - 70 °C
Dopuszczalna wilgotność względna: 10 - 90 %
Model: Amplituner
Maks. rozdzielczość: 4096 x 2160 px
Maksymalna częstotliwość odświeżania: 60 Hz
Wersja HDMI: 2.0
HDCP: Tak
Szerokość pasma: 9.2 Gbit/s
Możliwości montowania w stelażu: Tak
System dźwięku: Wielokanałowy
Maksymalny dystans transferu: 100 m
Obsługiwane tryby wideo: 1080p, 2160p
Wersja HDCP: 2.2
Wejśćie 3,5 mm: Tak
Obsługiwane typy kabli: Cat6, Cat6a, Cat7, HDMI
Wejścia RJ-45: 1
Porty wejściowe RS-232: 1
Obsługa Consumer Electronics Control (CEC): Tak
Port HDBaseT: Tak
Rozszerzone dane identyfikacyjne wyświetlacza (EDID): Tak
Certyfikat HDBaseT: Tak

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z WyreStorm RXV-70-4K, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje przedłużacz AV WyreStorm

Instrukcje przedłużacz AV

Najnowsze instrukcje dla przedłużacz AV