Instrukcja obsługi WyreStorm EX-40-G3

WyreStorm przedłużacz AV EX-40-G3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla WyreStorm EX-40-G3 (4 stron) w kategorii przedłużacz AV. Ta instrukcja była pomocna dla 7 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

1080p HDMI-over-UTP Extender with IR and PoC

EX-40-G3 Quickstart Guide

EX-40-G3 Quickstart Guide | 190121

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

1 of 4

WyreStorm recommends reading through this document in its entirety to become familiar with the product’s features prior to starting the

installation process.

Basic Wiring Diagram

IMPORTANT! Installation Requirements

• Visit the product page to download the latest rmware, document version,

additional documentation, and conguration tools.

• Read through the section for important wiring Wiring and Connections

guidelines before creating or choosing premade cables.

• While this product supports CEC, WyreStorm cannot guarantee

compatibility with all forms of CEC communication.

In the Box

1x EX-40-G3 Transmitter

1x EX-40-G3 Receiver

1x 5V DC 1A Power Supply (US/UK/EU/AU)

1x USB-A to Micro-B RX Power Cable

1x IR Emitter

1x IR Receiver

4x Mounting Brackets (2x for TX | 2x for RX)

1x Quickstart Guide (this document)

IR to Control System

CAB-IR-LINK (Sold Separately)

5V DC

Power Supply

5V DC

Power Supply

HDMI Display

EX-40-G3

Transmitter

EX-40-G3

Receiver

HDBaseT Cat5e/6/6a

HDMI Source

HDMI HDMI

KEY

HDMI

HDBaseT

Power

Transmitter (TX)

Front Panel

Rear Panel

Front Panel

Rear Panel

Receiver (RX)

Power Input 5.5mm Screw Down Barrel Jack

Connect to the included power supply.

HDMI In 19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

UTP Out 8-pin RJ-45 female

Connect the UTP In on the receiver (RX)

UTP In 8-pin RJ-45 female

Connect the UTP Out on the receiver (RX)

USB 5V

BackUp Power

USB Mirco. Connect to USB power when PoC

cannot be used

HDMI Out 19-pin type A HDMI female

Supports HDMI and DVI/D with adapter

CLong Cable Mode

Extends the distance of the AV transmission

past the normal operating distance of

30m/98ft. Refer to section Long Cable Mode

for more details

EX-40-G3 Quickstart Guide | 190121

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

2 of 4

B CA

Troubleshooting

No or Poor Quality Picture (snow or noisy image)

• Verify that power is being supplied to the transmitter and receiving device.

• Verify that all HDMI and UTP connections are not loose and are functioning

properly.

• Verify that the HDBaseT cable is properly terminated following EIA568B

standard.

• Verify that the output resolution of the source and display is supported by

this extender.

• If transmitting 3D or 4K, verify that the HDMI cables used are 3D or 4K rated.

No or Intermittent 3rd party Device Control

• Verify that the IR and RS-232 cables are properly terminated following the

Wiring and Connections section.

Troubleshooting Tips:

• WyreStorm recommends using a cable tester or connecting the cable to

other devices to verify functionality.

EX-40-G3 Quickstart Guide | 190121

UK: +44 (0) 1793 230 343 | ROW: 844.280.WYRE (9973)

support@wyrestorm.com

3 of 4

Wiring and Connections

WyreStorm recommends that all wiring for the installation is run and terminated prior to making connections to the switcher. Read through this section in it’s

entirety before running or terminating the wires to ensure proper operation and to avoid damaging equipment.

IMPORTANT! Wiring Guidelines

• The use of patch panels, wall plates, cable extenders, kinks in cables, and

electrical or environmental interference will have an adverse effect on

signal transmission which may limit performance. Steps should be taken

to minimize or remove these factors completely during installation for best

results.

• WyreStorm recommends using pre-terminated HDMI cables due to the

complexity of these connector types. Using pre-terminated cables will

ensure that these connections are accurate and will not interfere with the

performance of the product.

IR TX/RX Guidelines

• Using WyreStorm infrared emitters and receivers is the best way to ensure

that most IR coding formats are transmitted and received by the NetworkHD

system. Other 3rd party emitters and receivers can be used; however, these

devices must operate in the same manner as the WyreStorm devices.

• Due to differences in IR across 3rd party control systems their IR ports

should never be connected directly to a NetworkHD system as an

incompatibility may exist. WyreStorm offers a cable that compensates for

voltage differences as well adjusts for differences in the pins used within the

port. Refer to the product page for more information.CAB-IR-LINK

IR TX Port Pinout

Connection for IR TX (transmit) uses a 3.5mm (1/8in) mono plug.

Tip: Anode

Sleeve: Cathode (IR Signal)

IR RX Port Pinout

Connection for IR RX (receive) uses a 3.5mm (1/8in) stereo jack that outputs

+5V DC to power the included IR receiver.

Tip:

Ring: IR Signal

+5V DC

Sleeve: Ground (GND)

Long Cable Mode

This extender contains an option Long Cable Mode to extend the distance

of the AV transmission past the normal operating distance. Under normal

operation when using distances of 30m/98ft or less this feature should be

turned Off.

Set the switch to when the cable distance from Off

the TX to the RX is 30m/98ft or less.

Set the switch to to extend the cable distance On

from the TX to the RX up to 40m/131ft

Specyfikacje produktu

Marka:	WyreStorm
Kategoria:	przedłużacz AV
Model:	EX-40-G3
Kolor produktu:	Czarny
Wysokość produktu:	21 mm
Szerokość produktu:	70 mm
Głębokość produktu:	70.2 mm
Waga produktu:	200 g
Certyfikat środowiskowy (zrównoważonego rozwoju):	RoHS
Technologia łączności:	Przewodowa
Prąd:	1 A
Maksymalne zużycie mocy:	2.5 W
Napięcie pracy:	5 V
Zakres temperatur (eksploatacja):	0 - 45 °C
Zakres wilgotności względnej:	10 - 90 %
Kanały wyjścia audio:	2.0 kan.
Przewodowa sieć LAN:	Tak
Diody LED:	Tak
Zakres temperatur (przechowywanie):	-20 - 70 °C
Dopuszczalna wilgotność względna:	10 - 90 %
Model:	Nadajnik i odbiornik AV
Adapter zewnętrznego zasilania:	Tak
Maks. rozdzielczość:	1920 x 1200 px
Maksymalna częstotliwość odświeżania:	60 Hz
Wersja HDMI:	1.3b
HDCP:	Tak
Szerokość pasma:	6.75 Gbit/s
Możliwości montowania w stelażu:	Tak
System dźwięku:	Stereo
Maksymalny dystans transferu:	40 m
HDMI in:	1
Zdalne wejście IR:	1
Wersja HDCP:	1.4
Zdanlne wyjścia IR:	1
Obsługiwane typy kabli:	Cat6, Cat6a, Cat7, HDMI
Wejścia RJ-45:	1
Wyjścia RJ-45:	1
Rozszerzone dane identyfikacyjne wyświetlacza (EDID):	Tak