Instrukcja obsługi Wharfedale Diamond 101C

Wharfedale Głośniki Diamond 101C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Wharfedale Diamond 101C (12 stron) w kategorii Głośniki. Ta instrukcja była pomocna dla 8 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
1
Before installing this product read all these instructions!
Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.
Before making any connections, switch all the units in your system o at the mains.
Set the volume control at minimum when you switch on your system or change sources, and turn the level up gradually.
DO NOT use your amplier at full volume.
Ensure that all loudspeakers in the system are correctly wired.
DO NOT subject your loudspeakers to excessive cold, heat, humidity or sunlight.
Loudspeakers should not be placed directly facing other hi- units, or share the same shelf or cabinet.
DO NOT place heavy objects on top of loudspeakers.
Some manufacturers forbid the placing of objects on top of their TV sets. Check your TV handbook before installing the speaker directly on your
TV set. Consult your TV dealer if you are in any doubt.
DO NOT connect speaker terminals to the mains supply.
DO NOT dismantle the loudspeaker. There are no user serviceable parts inside it and you will void the warranty by doing so.
Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, the apparatus has
been exposed to rain or moisture, does not operate normally, or has been dropped.
Caution: Changes or modications not expressly approved by the manufacturer could void the user's authority to operate this device.
Unpacking Your Loudspeaker
Diamond 100 loudspeakers come in dierent shapes and sizes. If you are unpacking a oor stander, please remember that these units are heavy.
We suggest that you have someone to assist you.
Li the loudspeaker carefully out of the packing. try and li the loudspeaker using the protective bag.DO NOT
Unpack the accessories carefully.
If there is any sign of damage or if the contents are incomplete, report this to your dealer as soon as possible.
Retain the packing for future safe transport of the product. If you dispose of the packing, do so with respect to any recycling provisions in your area.
Attaching the Spikes to Floorstanding Models – 155, 156, 157, 159
· Make sure you have plenty of unobstructed working space.
· Place a so cloth on the oor to protect the loudspeaker.
· Invert the loudspeaker onto the cloth.
· Thread a locknut onto each spike and loosely rub it up the thread.
· Thread the spikes into the spike inserts. Tighten them nger tight.
· Invert the loudspeaker. Be careful not to damage the oor with the spikes.
Levelling the Loudspeakers
When the speaker is upright: You will probably nd that the speaker will wobble with one spike not contacting the oor. Adjust this spike until
all four spikes are in contact to the oor.
With the aid of a spirit level move each spike in and out until the loudspeaker is level and siing squarely on all four
spikes without rocking.
Now tighten each locknut securely against the collar in the plinth to secure the spike.
Screw in rubber feet are provided for use on wood or stone oors etc. and should be aached in the same manner as the
spikes.
Important Safety Information
This symbol indicates that there are important operating and maintenance instructions in the literature
accompanying this unit.
1
Stands and Brackets
The bookshelf loudspeakers are intended primarily for stand mounting, though they can be mounted on wall brackets or even on sturdy
shelves. The quality of loudspeaker stands greatly inuences the performance of your loudspeakers, please do not use imsy products.
Centre Channel Loudspeakers
Each centre channel loudspeaker is supplied with two sets of mounting feet. By using combination of large and small feet the loudspeaker may
be angled to point directly at the listening position. This will be found useful when the centre speaker is positioned under the TV screen.
Preparing the Diamond 100 Loudspeakers
Cables and Connectors
Choosing Loudspeaker Cable
Specialist audio cable usually oers beer performance than general purpose 'bell' or 'zip' wire.
Choose a cable of suitable diameter – cable that is too thin will limit the dynamics of the sound and may impair the bass response. Audio cable
is polarised, with two cores of dierent colours, or oen a raised rib or coloured tracer in the case of twin cable. Before you purchase your cable,
give careful thought to the positioning of your loudspeakers.
This is especially the case if you are bi-wiring your loudspeakers.
Cable lengths to loudspeaker pairs should be the same for le and right channels in order to equalise the signal
transmission. Allow some slack in your speaker cables so you can alter their position to best advantage.
Preparing Loudspeaker Cable
Split the twin cores to a depth of about 40mm. Carefully strip the insulation from each end, leaving about 10mm of
bare wire. If the cable is stranded, lightly twist to gather any loose strands.
Connecting Screw Terminals
All loudspeakers use screw terminals.
Unscrew the terminal. Insert the bare end of the cable into the hole in the base of the terminal. Tighten securely.
When connecting terminals make sure you leave no strands of bare wire that can short across to adjacent terminals.
As an alternative to bare wire you can use specialist spade connectors. Your Wharfedale dealer will be pleased to
advise you on this issue.
Crossover Networks
Bi-Wireable Networks
Most speakers in the Diamond 100 series use a special bi-wireable crossover panel with four
terminal binding posts. Please follow the drawing carefully to see the correct orientation of the
loudspeaker terminals. The upper terminals connect to the treble unit, the lower pair to the bass
unit. As supplied, the treble terminal pair is connected to the bass terminal pair via removable
metal straps. These should be le in place for standard installations.
Why Bi-Wire?
Using separate cables for treble and bass units in a bi-wiring configuration reduces
intermodulation eects and improves headroom and clarity. To bi-wire, you will need to install
two lengths of twin core cable between the amplier and each loudspeaker.

Specyfikacje produktu

Marka: Wharfedale
Kategoria: Głośniki
Model: Diamond 101C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Wharfedale Diamond 101C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Głośniki Wharfedale

Wharfedale

Wharfedale Diamond 8.2 Pro Instrukcja

14 Października 2024
Wharfedale

Wharfedale Jade SR Instrukcja

5 Lipca 2024
Wharfedale

Wharfedale Jade 5 Instrukcja

4 Lipca 2024
Wharfedale

Wharfedale Diamond 101C Instrukcja

4 Lipca 2024

Instrukcje Głośniki

Najnowsze instrukcje dla Głośniki

Steren

Steren SPK-1100BL Instrukcja

15 Października 2024
Pyle

Pyle PBMSPG6 Instrukcja

14 Października 2024
Marshall

Marshall Tufton Instrukcja

14 Października 2024
Sunstech

Sunstech SPUBT780 Instrukcja

14 Października 2024
Definitive Technology

Definitive Technology Mythos XTR-50 Instrukcja

14 Października 2024
Bang & Olufsen

Bang & Olufsen BeoLab Penta Instrukcja

13 Października 2024
Marquant

Marquant 002-222 Instrukcja

13 Października 2024
Naxa

Naxa NAS-3060 Instrukcja

13 Października 2024
Philips

Philips SPA1301 Instrukcja

13 Października 2024
Bang & Olufsen

Bang & Olufsen BeoLab 6002 Instrukcja

13 Października 2024