Instrukcja obsługi Weldex WDAC-5700C

Weldex Kamera monitorująca WDAC-5700C

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Weldex WDAC-5700C (12 stron) w kategorii Kamera monitorująca. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF
Strona 1/12
V.11I
Digital BOX Camera Installation Guide2
1.0 Features
Digital BOX Camera Installation Guide 3
1/3”Sony Super HAD CCD II : 410K(NTSC)/470K(PAL) pixels
High Resolution 600 TV Lines
Day & Night (ICR)
Digital Wide Dynamic Range
Digital Noise Reduction
Privacy mask Function
On Screen Display
Motion detection
Parking Line
High Light Compensation
IR Smart
Regulatory Notice
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions :
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class A
These limits are designed to provide
digital device, pursuant to Part 15 of the FCC Rules.
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
may cause harmful interference
installed and use in accordance with the instructions,
to radio communications.
Operation of this equipment in a residential area is likely to cause interference, in which
interference at his own expense.
case the user will be required to correct the
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK),
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The ligh nint g f h las with an arrowhead sy , mbol wi hit n an equila erat l t e is riangl in endet d to alert the user to the presence of uninsulated
dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.
The exclama iot n point wi hit n an equila erat l t e is riangl in endet d to alert the user to the presence of impor ant t opera int g and m t ceain enan
(servicing) instructions in the literature accompanying the appliance.
WARNING-
Changes or modicat s ion not ex ly press approved by the manu urefact r c d v d the us s oul oi er au horit ty to operate the equipment.
CAUTION- To prevent electric shock and risk of re hazards:
Do NOT use power sources other than that specied. Do NOT expose this appliance to rain or moisture.
2.0 Warnings
The camera needs periodic inspection.
Contact an authorized technician for inspection.
Stop using your camera when you find a malfunction.
If you use your camera around smoke or unusual heat for a long time, fire may be caused.
Do not Install the camera on a surface that can not support it.
Unless the surface is suitable, it could cause falling or other hazards.
Do not hold plug with wet hands.
It could cause an electric shock.
Do not disassemble the camera.
It may result in fire, electric shock or other hazards.
Do not use the camera close to a gas or oil leak.
It may result in fire or other hazards.
Digital BOX Camera Installation Guide4
Digital BOX Camera Installation Guide 5
3.0 Precautions
Do not install the camera in extreme
temperature conditions.
Only use the camera under conditions
where temperatures are between -10
Deg. C and +50 Deg. C.(14 Deg. F and
122 Deg. F) Be especially careful to
provide ventilation when operating
under high temperatures.
Do not insta ll or use th e camera in an
environment where the humidity is high.
It can cause the image quality to be
poor.
Do not install th e camera under
unstable lighting conditions.
Severe lighting change or flicker can
cause the camera to work improperly.
Do not touch the front lens of the
camera.
It is one of the most important parts
of the camera. Be careful not to be
stained by fingerprint.
Do not drop the camera or subject
them to physical shocks.
It can cause malfunctions to occur.
Never keep the camera face to
strong light directly.
It can damage the CCD.
Do not expose the camera to rain
or spill beverage on it.
If it gets wet, wipe it dry immediately.
Liquids can contain minerals that
corrode the electronic components.
Do n o t e xp os e th e ca me ra to
radioactivity.
If it is exposed to radioactivity, For
heated CCD, it will be out of order.
Note
If the camera is exposed to spotlight or object reflecting strong light, smear or blooming may occur.
Please check that the power satisfies the normal specification before connecting the camera.

Specyfikacje produktu

Marka: Weldex
Kategoria: Kamera monitorująca
Model: WDAC-5700C

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Weldex WDAC-5700C, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą


Instrukcje Kamera monitorująca Weldex

Weldex

Weldex WDAC-5700C Instrukcja

22 Września 2024
Weldex

Weldex WDAC-4277DT Instrukcja

20 Września 2024
Weldex

Weldex WDC-4605XV Instrukcja

20 Września 2024

Instrukcje Kamera monitorująca

Najnowsze instrukcje dla Kamera monitorująca

Trebs

Trebs CCD-401C Instrukcja

15 Października 2024
Hikvision

Hikvision DS-2CE56D5T-AIRZ Instrukcja

15 Października 2024
D-Link

D-Link DCS-7510 Instrukcja

15 Października 2024
Ubiquiti Networks

Ubiquiti Networks UniFi Video UVC-G3-AF Instrukcja

14 Października 2024
Hikvision

Hikvision DS-2TD2137-7/VP Instrukcja

13 Października 2024
Alecto

Alecto DVC-215IP Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2DE7A245IX-AE/S1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2TD2166-15/V1 Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2325FWD-I Instrukcja

13 Października 2024
Hikvision

Hikvision DS-2CD2323G2-IU Instrukcja

12 Października 2024