Instrukcja obsล‚ugi WAC Lighting WS-23018

WAC Lighting Ulga WS-23018

Przeczytaj poniลผej ๐Ÿ“– instrukcjฤ™ obsล‚ugi w jฤ™zyku polskim dla WAC Lighting WS-23018 (2 stron) w kategorii Ulga. Ta instrukcja byล‚a pomocna dla 2 osรณb i zostaล‚a oceniona przez 2 uลผytkownikรณw na ล›rednio 4.5 gwiazdek

Strona 1/2
dweLED.com
Phone (800) 526.2588
Fax (800) 526.2585๎˜ƒ
Headquarters/Eastern Distribution Center
44 Harbor Park Drive
Port Washington, NY 11050
๎˜ƒ
Central Distribution Center
1600 Distribution Ct
Lithia๎˜ƒSprings,๎˜ƒGA๎˜ƒ30122
Western Distribution Center
1750 Archibald Ave
Ontario, CA 91761
WAC Lighting retains the right to modify the design of our products at any time as part of the company's continuous improvement program. Oct. 2019 2
๎˜ƒ
INSTALLATION INSTRUCTIONS
220 โ€“ LED Wall Sconce
WS-22018
Fig.1๎˜ƒ
PREPARATION
1. Shut off the power at the circuit breaker and remove existing fixture, including the crossbar.
2. Carefully unpack your new fixture and lay out all the parts on a clear area. Be careful not to lose any small parts necessary for
installation.
MOUNTING THE FIXTURE (Fig. 1)
3. Remove the mounting screw (B) from the fixture.
4. Secure the mounting back plate to the junction box using the screws provided with the junction box.
NOTE: (i) using any other non-original-manufacturer provided junction box screws may result in safety issue;
(ii) the side of the mounting plate marked โ€œGNDโ€must face out.
CONNECTING THE WIRES (Fig. 2)
5. Connect the driverโ€™s input wires to junction box wires as shown (Fig. 2). Make sure that all wire connectors (A) are secured. If
your outlet box has a green or bare copper ground wire, connect the fixtureโ€™s ground wire to it. Otherwise, connect the fixtureโ€™s
ground wire directly to the back plate using the green screw provided. After wires are connected, tuck them carefully inside the
junction box.
6. Secure the fixture to the mounting back plate using the mounting screw (B).
DIMMING WIRING INFORMATION (Fig. 3)
7. This fixture features electronic low voltage (ELV or TRAIC) dimming capabilities. See notes below for specific dimming wires
information.
8. To utilize ELV or TRAIC dimming: use wires black (hot), white (neutral) and bare copper ground wire (ground).
9. To utilize 0-10V dimming: use wir e purple (dim+), gray (dim-),black (hot), white (neutral) and bare copper ground wire (ground).
NOTE: Make sure to connect 0-10V prior to power-up the fixture in order to allow the 0-10V dimming to function properly.
Fig. Fig.๎˜ƒ ๎˜ƒ2 Wiring๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ ๎˜ƒ3๎˜ƒ๎˜ƒ
๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ๎˜ƒ ๎˜ƒ
Fixture Wires
Black or
Smooth
Fixture Wires
White or
Ribbed
Fixture Wires
Bare Wire
(Ground)
House Wires
Black
(Hot)
House Wires
White
(Neutral)
House Wires
Green or Bare Copper
(Ground)
White - Neutral
Black - Hot
Purple - Dim+
Grey - Dim-
Red - Fixture+
Black - Fixture-
Back Plate Dimensions
13
4" 13
8"
65
8"
43
8"
B
A
Wire Connector
Mounting Screw
Driver
Mounting๎˜ƒ
Back๎˜ƒPlate
Junction Box
Bare Copper
Ground Wire
Black Wire
White Wire
Junction
Screw


Specyfikacje produktu

Marka: WAC Lighting
Kategoria: Ulga
Model: WS-23018

Potrzebujesz pomocy?

Jeล›li potrzebujesz pomocy z WAC Lighting WS-23018, zadaj pytanie poniลผej, a inni uลผytkownicy Ci odpowiedzฤ…




Instrukcje Ulga WAC Lighting

Instrukcje Ulga

Najnowsze instrukcje dla Ulga