Instrukcja obsługi Viking K-1900-812L

Viking Intercomsysteem K-1900-812L

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Viking K-1900-812L (4 stron) w kategorii Intercomsysteem. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/4

Vandal Resistant Hot-Line Panel Phone with Keypad

Features

• Vandal Resistant Features: 12 gauge (0.105” thick) 316

stainless steel panel with permanent laser etched graphics,

armored cable, metal cradle, heavy-duty metal keypad, and hex

drive mounting screws

• Marine grade 316 stainlessWeather Resistant Features:

steel faceplate and screws, and internally sealed keypad

• Auto dials one programmable speed dial number (up to 32 digits)

• Multi-number dialer mode adds 5 speed dial numbers (up to 16 digits)

• Touch tone or pulse dialing

• Non-volatile memory (no batteries required)

• Operates on analog PABX and key system extensions or analog

Centrex and CO lines

• Programmable 6 digit security code

• Touch tone programmable

• Optional Enhanced Weather Protection (EWP) available

- EWP products

are designed to meet IP66 Ingress Protection Rating, see DOD 859

• 12” armored handset cable on andK-1900-812L K-1900-812L-EWP

• 36” armored handset cable on K-1900-8

• 54” armored handset cable on K-1900-8-EWP

• Programmable pre-dial pause

• Blocks fraudulent calls from hand held pocket dialers

• Limited toll Restriction in dumb phone mode

• Hearing aid compatible amplified handset with sealed push

button volume control

• Programmable default volume level

• Programmable volume control disable

• Flush mount with included steel rough-in box, or use an optional

VE-5x10 DOD 424surface mount box (not included, see )

• Catalog sales

• Kiosks

• Courtesy and customer service phones

• Automated tellers (ATM’s)

• Hot-line reservation phones

• Security and emergency phones

• Replaces leased ringdown circuits

• Gate/entrance communication in noisy locations

(diesel trucks, factory noise, etc.)

Power: Telephone line powered (20V DC/18mA minimum)

Dimensions for Standard Model

Phone : 5.0” x 10.0” x 4.54” (127mm x 254mm x 113mm)

With rough-in box: 5.0” x 10.0” x 5.53” (127mm x 254mm x 141mm)

Dimensions for EWP Model

Phone: 5.0” x 10.0” x 4.93” (127mm x 254mm x 125mm)

With rough-in box: 5.0” x 10.0” x 5.61” (127mm x 254mm x 143mm)

Shipping Weight: 5 lbs (2.3 kg )

Operating Temperature: -30°F to 140°F (-34°C to 60°C)

Humidity - Standard Model: 5% to 95% non-condensing

Humidity - EWP Model : Up to 100% condensing

K-1900-812L(EWP) Handset Cable Length: 12” to 12.7” (31 cm to 33 cm)

K-1900-8 Handset Cable Length: 34” to 37” (86 cm to 94 cm)

K-1900-8-EWP Handset Cable Length: 52” to 57” (132 cm to 145 cm)

Touch Tone Dial Speed: Normal = 120ms on/off, Fast = 50ms on/off

Pulse Dial Speed: Normal = 10 pps, Fast = 20 pps

Connections: (2) gel-filled butt connectors

Applications

Specifications

www.VikingElectronics.com

Information: 715-386-8861

The K-1900-8 Series panel phone can either auto-dial a phone

number each time the handset is lifted, be used as a multi-number

auto-dialer, or be used as a standard (dumb) phone. The unit will

touch tone or pulse dial and will not auto-dial on incoming calls.

The K-1900-8 Series housing consists of a heavy gauge stainless

steel panel, metal touch tone keypad, armored cable, heavy duty

handset, and all metal cradle. The can be easilyK-1900-8 Series

touch tone programmed at the shop or installation site. All

programming is stored in non-volatile memory.

The andK-1900-812L K-1900-812L-EWP feature a 12” long

armored cable with an internal stainless steel lanyard for additional

cable strength.

The and K-1900-8-EWP K-1900-812L-EWP share all the features

of the K-1900-8 and K-1900-812L in addition to Enhanced Weather

Protection (EWP) for outdoor installations where the unit is exposed

to precipitation or condensation. EWP products are designed to

meet IP66 standards and may feature foam rubber gaskets, sealed

connections, gel-filled butt connectors, as well as potted circuit

boards with internally sealed, field-adjustable trim pots and DIP

switches for easy on-site programming. For more information on

EWP, see .DOD 859

Note: If a ringer is required, use an external unit such as the Viking

SR-1 DOD 477 LPR-1 DOD 550( ), or ( ).

K-1900-8-EWP

with 54”

armored cable

K-1900-8

with 36”

armored cable

K-1900-812L /

K-1900-812L-EWP

with 12” armored

cable and lanyard

DESIGNED, MANUFACTURED AND SUPPORTED IN THE USA K-1900-8 Series

Hot-Line Panel Phone

with Keypad

June 4, 2020

PRODUCT

MANUAL

SECURITY & COMMUNICATION

VIKING

Installation

10.14"

3.69"

5.22"

Optional VE-5x10 Surface

Mount Box (not included)

10.0"

9.5"

4.04"

4.50"

5.00"

5.12"

1.72"

0.23"

Front View

of the K-1900-8

5.5"

2.5"

4.5"

- or -

Zinc-Plated Steel

Rough-In Box (included)

Side View

of the K-1900-8

(8) #6-32 x 3/4"

Stainless Steel Hexdrive

Screws (included)

C.O. Line

or Analog

PABX/KSU

Station

K-1900-8-EWP

shown with

optional

VE-5x10 and

VE-GNP

Gooseneck

Pedestals

(not included)

*Gel-Filled

Butt Connectors

(included)

Red

Green

VE-GNP

B. Accessing the Programming Mode

Programming

1. Remote Programming

Step 1. K-1900-8Connect the green and red wires on the to a C.O. line or analog PABX/KSU station.

Step 2. ONIf using the multi-number dialer mode, set DIP switch 2 to .

Step 3. From a Touch Tone phone, call the line connected to the .K-1900-8

Step 4.

Take the off-hook (remove handset from the cradle). From the calling phone enter “ ”K-1900-8 Q

followed by the six digit security code, factory set to (see section above). A double beep845464 A

will indicate that programming has been entered.

Step 5. D - IProgram as shown in sections .

Step 6. To exit programming, hang up both phones.

2. Programming Without Using the Security Code

Step 1. K-1900-8Connect the green and red wires on the to a C.O. line or analog PABX/KSU station.

Step 2. Set DIP switch to .1 ON

Step 3. If using the multi-number dialer mode, set DIP switch 2 to .ON

Step 4. From a Touch Tone phone, call the line connected to the .K-1900-8

Step 5. Take the off-hook (remove handset from cradle). A double beep should be heardK-1900-8

indicating you have entered programming.

Step 6. D - IProgram from calling phone as shown in sections .

Step 7. Set DIP switch back to .1 OFF

Step 8. To exit programming, simply hang-up the phones.

To install the panel phone, attach the panel using the provided screws or use the optional K-1900-8 VE-5x10 weather

resistant surface mount box. Note: Four extra screws and nuts are provided to fill the unused mounting holes. The

optional VE-5x10 surface mount box (shown below) is designed to be surface mounted to a wall, post, single gang

box or a goose neck pedestal (shown right). The can also be mounted in an optionalVE-GNP VE-GNP-2or K-1900-8

VE-9x20 Weatherproof Enclosure (DOD 413). Note: When mounting a K-1900-8-EWP VE-9x20in a , the length of

the handset cable must be reduced. Use a 3/32” hex key or bit to loosen the set screw in the brass handset cable

retainer. Pull approximately 18 inches of the cable through the panel and retighten the set screw.

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC

outlet and the telephone line. It is recommended that a surge protector be installed to protect against such surges.

* Note: The gel-filled (water-tight) butt connectors are designed for insulating displacement on

19-26 gauge wire with a maximum insulation of 0.082 inches. Cut off stripped wire ends before terminating.

A. Security Code

Step 1. BAccess programming as shown in section .

Step 2. #47Enter your new security code followed by .

Step 3. To exit programming simply hang up the .K-1900-8

A six digit number may be used to access the programming mode. The security code has been factory set to

845464 (V-I-K-I-N-G). It is recommended that you change the security code to a personal 6 digit number:

Note: #The security code must be six digits in length and contain a MUST NOT Qor . If you have forgotten your

security code, see section “ .”B, 2. Programming Without Using the Security Code

Description Enter Digits + Location

Speed dial number ............................................................................................................................... 1-32 digit (0-9) + #00

Multi-number auto-dialer numbers 1-5 (DIP switch 2 must be ) ......................................................ON 1-32 digit (0-9) + #01-#05

Q QQ (anywhere in the speed dial number) ...............................................................................................

# (anywhere in the speed dial number) ...............................................................................................Q#

Set dialing speed to normal (Touch Tones: 120ms on/off, Pulse: 10 pps) (factory setting) ..................Q1

Set dialing speed to fast (Touch Tones: 50ms on/off, Pulse: 20 pps) ...................................................Q2

Block hand held pocket dialers (factory setting) ..................................................................................Q3

Allow hand held pocket dialers ............................................................................................................ Q4

Normal pre-dial pause (approximately 1.4 sec) (factory setting) .........................................................Q5

Short pre-dial pause (approximately 800 ms) ......................................................................................Q6

To add a one second pause at any point in the dialing string .............................................................. #7

To add a four second pause at any point in the dialing string .............................................................. Q7

Toggle between Pulse and Touch Tone dialing (see section ) ............................................................IQ8

Disable toll restriction (factory setting) ..................................................................................................Q9

Enable toll restriction ............................................................................................................................Q0

Set default volume 1-4 (1 = min, 4 = max) and control (1 = enabled, 2 = disabled) (factory 1,1) ..... 2 digits (1-4,1-2) + #46

Change security code .......................................................................................................................... 6 digits (0-9) + #47

To clear the speed dial number and return all programming to factory settings .................................. ###

To set the dialing speed, access the , then choose a speed. To set the dialing speed toProgramming Bmode as shown in section

Normal (Touch Tone: 120ms on/off, Pulse: 10pps), enter . To set the dialing speed to (Touch Tone: 60ms on/off, Pulse:Q1 Fast

20pps), enter .Q2

OFF ON

DIP

Switches

Internal View of

the K-1900-8-EWP

OFF

DIP

Switches

Internal View of

the K-1900-8

J. DIP Switch Programming

Switch Position Description

1 ON Learn Mode

1 OFF Normal Operation (factory setting)

2 ON Multi-Number Dialer Mode

2 OFF Normal Operation (factory setting)

Note: DIP switch 3 is not used and should remain in the OFF

position.

Note: Special features such as Q, #, a mode change and a pause, use single digits in the programming memory.

E. Dialing Speed

The K-1900-8 is programmed to hang-up if it detects Touch Tones it did not generate. This helps prevent toll fraud from hand held

dialers. To set the to block/allow dialing from external devices, access the mode as shown in section K-1900-8 Programming B,

then choose block or allow. To hand held dialers, enter Block Q3. To Allow Touch Tones from external devices, enter .Q4

F. Hand Held Pocket Dialers

In the single number auto-dialer mode, the time from when the handset is taken off-hook until the auto-dials can beK-1900-8

programmed. Access the Programming mode (section ), then choose a pause length. To set the pause length to B Normal

(approximately 1.4 seconds), enter . To set the pause length to (approximately 800ms) enter .Q5 Short Q6

G. Pre-Dial Pause

To set pauses in the dialing string, access the mode as shown in section , then enter to put a 4 second pauseProgramming B Q7

anywhere in the dialing string, or for a 1 second pause.#7

H. Pauses in the Dialing String

These examples would be entered after accessing the Programming mode as shown in section .B

K. Programming Examples

To Program the K-1900-8 to... Enter Digits Enter Location

...Touch Tone dial 555-1234 5551234 #00

...pulse dial 555-1234 followed by a Touch Tone 9 Q Q8 5551234 8 9 #00

...clear the speed dial number #00

C. Programming Features Quick Reference

The K-1900-8 can operate in 3 different modes. With DIP switch 2 OFF #00 K-1900-8set to and memory location cleared, the is in

the Standard (Dumb) Phone mode. With DIP switch set to and a phone number programmed in memory location , the2 OFF #00

K-1900-8 is in the Single Number Auto-Dialer mode. With DIP switch set to , the becomes a Multi-Number Auto Dialer.2 ON K-1900-8

D. Dialer Modes

When the is in the Standard (Dumb) phone mode, some limited toll restriction is available. With toll restriction enabled, theK-1900-8

phone will hang-up if a 0 or 1 is entered as the first digit, or if more than ten digits are entered. Access the Programming mode

(section B), then choose enable or disable toll restriction. To set the toll restriction, enter . To set the K-1900-8 Disableto Q9 K-1900-8

to toll restriction, enter .Enable Q0

I. Toll Restriction

Specyfikacje produktu

Marka:	Viking
Kategoria:	Intercomsysteem
Model:	K-1900-812L

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Viking K-1900-812L, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Intercomsysteem Viking

Viking K-1900-712L-EWP Instrukcja

9 Października 2024

Viking K-1700-3 Instrukcja

9 Października 2024

Viking E-50-SS Instrukcja

9 Października 2024

Viking E-50-WH Instrukcja

9 Października 2024

Viking K-1700-IP-EWP Instrukcja

9 Października 2024

Viking E-60-BN Instrukcja

9 Października 2024

Viking E-1600-53-IP Instrukcja

9 Października 2024

Viking E-60-WH Instrukcja

9 Października 2024

Viking K-1900-8-IP-EWP Instrukcja

9 Października 2024

Viking W-2000A Instrukcja

9 Października 2024

Instrukcje Intercomsysteem

Najnowsze instrukcje dla Intercomsysteem

FlyingVoice i86V-01 Instrukcja

9 Października 2024

Valcom V-1072B Instrukcja

8 Października 2024

Valcom V-1074 Instrukcja

8 Października 2024

Valcom V-2972 Instrukcja

8 Października 2024

Valcom V-9953 Instrukcja

8 Października 2024

Valcom V-TR96 Instrukcja

8 Października 2024

Valcom V-5324004 Instrukcja

8 Października 2024

Valcom V-9908 Instrukcja

8 Października 2024

Valcom V-9923B Instrukcja

8 Października 2024

Valcom V-1096 Instrukcja

8 Października 2024