Instrukcja obsługi Viking E-40-SS-EWP

Viking Interkom E-40-SS-EWP

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Viking E-40-SS-EWP (8 stron) w kategorii Interkom. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/8

Compact Entry Phones available in Four Attractive Finishes

Features Applications

Specifications

• Compact size: Front panel is the size of a typical single gang mid-size

wall plate

• Mounting: Flush mounts in a single gang electrical box (2.25” deep x

2.00” wide x 2.84” tall minimum) or surface mounts in a Viking model

VE-3x5 DOD 424 (not included, see ) for mounting on a wall, post or

VE-GNP Gooseneck Pedestal (EWP recommended)

• Available in 4 standard faceplate finishes: Brushed Stainless Steel,

Oil Rubbed Bronze, Satin Black and Satin White

• PNL-40 faceplates: Replacement faceplates with matching screws

available in all four standard finishes

• Vandal Resistant Features: 18 gauge 304 stainless steel faceplate,

316 stainless steel push button, fiberglass reinforced plastic speaker

screen, scratch resistant powder coating, hex drive mounting screws

• Weather Resistant Features: Mylar speaker, faceplate gasket,mic

and speaker gasket, internally sealed (IP67) push button switch, self

draining mic mount and UV stable weather resistantpowder coating

(excluding 304 Stainless Steel faceplate) E-40-SS

• is designed to meet IP66 Ingress Protection Rating (see E-40-EWP

DOD 859 for more information)

• Telephone line powered

• Microphone and speaker volume controls

• Programmable intelligent call progress detection for automatic hang-up

on CPC, silence, busy signal, or time out

• Selectable auto answer feature for monitoring

• Programmable VOX (mic/speaker) switching speed

• Blue LED helps locate push button, indicate ringing and off hook

• Door or gate communication, business delivery entrances

• Use with a or to control on a single line Viking C-200 C-250 E-40

• Use with a to control 1 or 2 (expandable to 8) Viking C-500 E-40’s

and door/gate control on a single phone line

• Use with a to control 1 to 4 ’s and door/gate Viking C-2000B E-40

control on a single phone line

• Provide unique front and back door chimes and paging when

used with a , and Viking SLP-1 SLP-4 C-2000B

• Residential, commercial and industrial door security

• Use with a or for automatic speed Viking K-1900-5 K-1900-30

dialing on telephone lines or analog PABX/KSU station ports

• Use on any analog PABX station port with programmable

ringdown capability

The E-40 Series entry phones are compact,

weather and vandal resistant, telephone line

powered speaker phones designed to provide

two-way handsfree audio communication. The

E-40's compact size allows it to be mounted in

a standard single gang electrical box. The E-

40 is available in four different attractive

finishes to match your door hardware, light

fixtures, etc. Replacement faceplatesE-40

( PNL40) can be purchased separately and are

available in all four standard finishes. The

E- 40’s blue LED continually provides light for

locating the push button in dark locations, dims

to indicate off hook and flashes during incoming calls.The entry phones can share a single phone line with house or smallE-40

business telephones when used with a model or Entry Phone controller. The entryViking C-200 500, C-250, C- C-2000B E-40

phones can also be connected to an unused analog station port (programmed for ring down) on a phone system or connected

directly to a telephone line when used with a Viking model K-1900-5 or K-1900-30 auto dialer. The E-40 features microphone and

speaker volume controls, selectable auto answer for monitoring and intelligent call progress detection for automatic hang-up when

the call is completed. For outdoor installations where the unit is exposed to precipitation or condensation, the Series is availableE-40

with Enhanced Weather Protection ( ). For more information on , see .EWP EWP DOD 859

Power: Telephone line powered. Minimum 18V DC talk battery

voltage with a minimum loop current of 20mA. Loop current may be

boosted on low current lines with a Viking model TBB-1B Talk Battery

Booster (see ). DOD 632

Dimensions: Faceplate: 4.875” x 3.125” x 0.18” (123.8mm x 79.4mm

x 4.6mm), Phone: 2.84” x 1.8” x 1.65” (72mm x 46mm x 42mm)

Shipping Weight: 1.0 lbs (0.45 kg)

Operating Temperature: -30° F to 150° F (-34° C to 65° C )

Humidity: Standard model: 5% to 95% non-condensing humidity,

EWP model: up to 100% humidity

Speaker Volume: Approximately 62db maximum @ 1m

Ring Voltage: 25V AC RMS minimum (for auto answer)

CPC Disconnect Time: 300ms minimum

REN: 0.8A

Connections: (2) gel-filled butt connectors

E-40-SS

“Brushed Stainless Steel”

(similar to brushed nickel) Shown

with optional surface VE-3x5

mount box

E-40-BK

“Textured Black”

(fine texture black

powder paint)

E-40-WH

“Satin White”

(satin white

powder paint)

E-40-BN

“Oil Rubbed Bronze”

(satin dark brown

powder paint with fine

copper metallic)

www.VikingElectronics.com

Information: 715-386-8861

DESIGNED, MANUFACTURED AND SUPPORTED IN THE USA E-40 Series

Compact Single Gang

Entry Phone with LED

September 2, 2021

PRODUCT

MANUAL

SECURITY & COMMUNICATION

VIKING

Features Overview

Installation

A. New Construction Flush Mounting

Step 1

Front of box should stick out approximately ½" from front surface of wall stud (this may

vary depending on the walls sheathing and siding thickness). Caution: Rough-In box

must be mounted and must stick out beyond the front surface of siding. LEVEL NOT

Step 2

To maintain a vapor barrier on outside wall applications, caulk around the box, filling any

gaps between the box and the rough opening. Apply caulk to any holes in the box around

wires, etc.

Step 3

When installing siding cut a hole just large enough for the Rough-In box opening.

Caution: Too large of a hole can cause plate misalignment and compromise the gasket

seal. Note: When mounting to 4 inch or less horizontal lap siding, the unit can be mounted

horizontally flush against siding or a siding mounting block can be used (recommended

with vinyl siding). Contact siding installer for the correct mounting block.

The E-40 is designed to be flush mounted into a single gang rough-in box with minimum inside

dimensions of 2.25” deep x 3.65” wide x 2.84” tall. The can also be surface mounted in a VikingE-40

model (not included, see ). VE-3x5 DOD# 424

WARNING: NOT E-40 Do use a typical “wet location box” as not all styles seal properly with the

faceplate.

Rear (PCB) View of E-40

Push Button Switch: Push to

initiate call, push again to

disconnect. Solid 316 stainless

steel internally sealed per IP67.

Speaker Screen: Speaker

screen with 0.018" wide slots to

prevent punctures from

paperclips, etc.

Faceplate Material: 18 gauge

304 stainless steel. The SS model

has a #4 brushed finish, the BK,

BN and WH models have a

powder painted finish.

Speaker: Mylar speaker with

rubber gasket to maintain

water-tight seal and eliminate

water deterioration.

Mounting Screws: (2) 6-32 x

3/4" Marine grade 316 stainless

steel, flat head, 5/64" hexdrive

screws (included).

Blue Call LED: Lights steady to

help locate the button in low light,

flashes during dialing, then lights

steady when answered.

Microphone: Omni-directional

microphone with protective

water-resistant cloth.

Front View of the E-40

Faceplate Gasket: 1/8" thick

closed cell PVC to provide a

water-tight seal.

Earth Ground: To increase

surge protection, loosen the

screw labeled (as shown)

and fasten a wire with ring

terminal (included) from the

mounting screw to Earth

Ground (grounding rod,

water pipe, etc.)

Speaker Volume

Microphone Volume

Entry Phone Board:

Compact analog speaker

phone with call progress

detection for automatic

disconnect.

DIP Switches (see page 6):

1: Auto Answer Feature (on/off)

2: Dial Tone Detection (on/off)

3: Programming Switch

(normal/programming)

4: LED (on/off)

B. Old Work / Remodel Flush Mounting (Using an recommended Carlon BH234R

Rough-In Box)

Step 1 .Make sure mounting location is free of wall studs, wires, etc.

Step 2

Place Rough-In box against siding. Trace outline of box onto siding. LEVEL Note: When mounting

to 4 inch or less horizontal lap siding, the unit can be mounted horizontally flush against siding or a

siding mounting block can be used. Contact your siding Installer for the correct mounting block part

number. A siding mounting block is recommended when mounting to vinyl siding..Note:

Step 3 Cut a hole through the siding and wall sheathing just large enough for the rough-in box. Caution:

Too large of a hole can cause plate misalignment and compromise the gasket seal.

Step 4 The front surface of the Rough-In box can be mounted flush against wood siding or can be recessed

and mounted flush against wall sheathing when mounting on aluminum, steel or vinyl siding.

Step 5

When mounting to 5/8 inch thick or less wall sheathing the two attached screws with wing brackets

can be used to secure the rough-in box. When mounting to surfaces thicker than 5/8 inch, four

standard flat head dry wall screws can be used to secure the Rough-In box through its mounting

ears. (See page 4 Section D.)

Step 6 To maintain a vapor barrier on outside wall applications, caulk around the box, filling any gaps

between the box and the rough opening. Apply caulk to any holes in the box around wires, etc.

C. Surface Mounting

A Viking model can be used to surface mount an to a wall or post. Drill a small wire exit hole in wall.VE-3x5 E-40

Pull wire through and seal hole around wire with putty or caulking. Route wire into the box, securely screwVE-3x5

it to wall or post and seal hole in box around wire with putty or caulking. Note: Conduit may also be used when

surface mounting wire, but should not enter through the top of the . When routing wiring from above, aVE-3x5

drip loop is required. WARNING: NOT Do use a typical “wet location box” as not all styles seal properly with the

E-40 faceplate.

D. Mounting the Faceplate

After the Rough-In box or is securely mounted, caulking between the box and rough opening is completedVE-3x5

(if required), and wires are connected, remove paper liner from face plate gasket. While firmly holding the LED

light pipe in the faceplate, carefully slide the faceplate gasket over the back of the light pipe and press gasket to

the back of the faceplate. Push the 1-1/4" 6-32 screws through faceplate holes and small holes in gasket, the

faceplate gasket should retain the screws. Position Circuit board mounting plate over screws. Align screws with

single gang box bosses and tighten face plate until gasket is fully collapsed and the push button is protruding

through the clearance hole in the face plate. Included 1/4" thick gasket will provide an adequate seal for most

siding surfaces; however for rough surfaces (ie: brick, stucco, etc.) additional caulking may be required.

(2) Gel-Filled

Butt Connectors

(included)

"Old Work" Rough-In Box

(Allied Molded 9331 box

shown, not included)

Circuit Board

Mounting Plate

(included)

1/4" Thick Foam

Faceplate Gasket

(included)

Facplate

(included)

Red

Green

(2) 6-32 x 1.25" Long

5/64" Hexdrive Flathead

Screws (included)

4.875"

3.125"

(4) Optional Dry

Wall Screws

(not included)

Optional

Mounting Ears Optional Wing

Brackets

*2.25"

Deep

Min.

1.8"

3.17"

4.92"

-OR-

Conduit Knockout

Condensation

Drain Hole

2.00"

Wide

Min.

2.84"

Tall Min.

Optional VE-3x5 Surface Mount

Box with Black Satin Powder Paint

Finish (not included) WARNING: Do

NOT use a wet location box.

** LED

Light Pipe

(included)

* CAUTION: Excessive wire length and/or using a rough-in box with inadequate depth can apply force to the

circuit board causing physical damage.

** Important: Push LED light pipe into faceplate hole, then place faceplate upside down on a clean flat surface

and push down on back side of plate until light pipe is fully seated and straight. WARNING: Inserting the light

pipe more than one time can cause a loose fit.

Specyfikacje produktu

Marka:	Viking
Kategoria:	Interkom
Model:	E-40-SS-EWP

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Viking E-40-SS-EWP, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Interkom Viking

Viking E-40-SS-EWP Instrukcja

28 Marca 2025

Viking E-1600-40-IPEWP Instrukcja

27 Marca 2025

Viking E-1600-20A-EWP Instrukcja

27 Marca 2025

Viking K-1900-712L-EWP Instrukcja

9 Października 2024

Viking K-1700-3 Instrukcja

9 Października 2024

Viking E-50-SS Instrukcja

9 Października 2024

Viking E-50-WH Instrukcja

9 Października 2024

Viking K-1700-IP-EWP Instrukcja

9 Października 2024

Viking E-60-BN Instrukcja

9 Października 2024

Viking E-1600-53-IP Instrukcja

9 Października 2024

Instrukcje Interkom

Najnowsze instrukcje dla Interkom

Hikvision DS-KABD9203-RS Instrukcja

27 Marca 2025

Hikvision DS-KH2230T Instrukcja

27 Marca 2025

Louroe Electronics AOP-SP-PB Instrukcja

10 Marca 2025

2N Telecommunications 9151104 Instrukcja

20 Lutego 2025

2N Telecommunications Indoor Compact Instrukcja

20 Lutego 2025

Axis TI8202 Instrukcja

20 Lutego 2025

Axis TI8904 Instrukcja

20 Lutego 2025

Rollei Xtalk Instrukcja

5 Lutego 2025

Hanwha SBS-165B Instrukcja

30 Stycznia 2025

Philips WelcomeEye Wireless Instrukcja

14 Stycznia 2025