Instrukcja obsługi Viking K-1700-3

Viking Interkom K-1700-3

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Viking K-1700-3 (8 stron) w kategorii Interkom. Ta instrukcja była pomocna dla 6 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/8
Vandal Resistant Handsfree
Entry Phones with Built-In Keypad
Features
The K-1700-3 Series entry phones provide a tough and
attractive handsfree phone for apartment, and residential door
entry or applications requiring a vandal resistant speaker
phone. The K-1700-3 Series entry phones are available in
two attractive finishes: brushed stainless steel” and “oil
rubbed bronze”.
When the “Call” button is pressed, the returns dialK-1700-3
tone. The keypad may then be used to dial any number. If
no Touch Tone is entered within 8 seconds, CPC is detected,
a busy signal is detected, or the programmable maximum call
time has elapsed, the will automatically disconnect.K-1700-3
Alternatively, the may be disconnected by pressingK-1700-3
the “Call” button again. The comes complete withK-1700-3
a standard, flush mount, rough-in box. In addition, an optional
VE-6x7 weather resistant, surface mount box is available (see
DOD 424).
The K-1700-3-EWP K-1700 shares all of the features of the -3
in addition to Enhanced Weather Protection (EWP) for outdoor
Apartment entry phone when used with the Apartment Entry Dialer K-1900-3
or Apartment/Office Entry Controller or C-4000 C-3000 Apartment Entry
Controller
• Use with a ( ) to control 1 or 2 (expandable to 8) Viking C-500 DOD 177
K-1700-3’s and door/gate control on a single phone line
• Use with a to control 1 to 4 s and door/gate control Viking C-2000B K-1700’
on a single phone line ( ) DOD 156
• Courtesy and customer assistance phone
Automated teller (ATM) phone
• Security or emergency phone
• Hot-Line phone when used with the Hot-Line Dialer ( ) K-1900-5 DOD 317
Note: When installing a line powered phone on a low voltage and/or low loop
current phone system extension, a Talk Battery Booster may be TBB-1B
required ( ). DOD 632
• Kiosk phone with (100 number speed dialing) when used with the K-1900-9
Multi-Number Dialer ( )DOD 321
Power: Telephone line powered 20V DC/20mA minimum
Dimensions: Overall: 5.5” x 6.5” x 2.6” (140mm x 165mm
x 66mm) , Rough-in box: 4.5 x 5.5” x 2.5 (114mm x
140mm x 64mm)
Shipping Weight: 3.5 lbs (1.6 kg)
Environmental: -30°F to 150°F (-34°C to 65°C)
Humidity - K-1700-3: 5% to 95% non-condensing
Humidity - K-1700-3-EWP: Up to 100% condensing
Speaker Volume: Approximately 70 db maximum @1m
CPC Disconnect Time: 500ms minimum
REN #: 0.5 A
Connections: Gel-filled tip and ring connectors
Applications
Specifications
www.VikingElectronics.com
Information: 715-386-8861
Vandal Resistant Features: 14 gauge louvered 316 stainless
steel faceplate with permanent laser etched graphics, stainless
steel “Call” button, heavy duty metal keypad and T-10 Torx
security mounting screws, scratch resistant powder coating
(model K-1700-BN)
Marine grade 316 stainless steel Weather Resistant Features:
faceplate, screws and and push button switch. Switch internally
sealed per IP67. Mylar speaker. Self-draining mic mount.
Faceplate, mic and speaker gaskets. Weather resisant powder
paint (K-1700-3-BN)
is designed to meet IP66 Ingress Protection K-1700-3-EWP
Rating (see for more information) DOD 859
Available in 2 standard faceplate finishes: 316 brushed stainless
steel or oil rubbed bronze
• Blue “in use” LED
• Telephone line powered
• Volume adjustments for microphone and speaker
Advanced call progress detection: disconnects on busy signal,
return to dial tone, CPC, reorder tone, maximum call time out and
40 second silence time out
• Selectable auto-answer feature for monitoring
• Selectable push button disconnect
• Zinc plated steel rough-in box with (2) 3/4” conduit knockouts
• Optional Surface Mount Box available VE-6x7
• Selectable VOX switching speed
K-1700-3
“Brushed 316 Stainless Steel”
(similar to brushed nickel)
K-1700-3-BN
“Oil Rubbed Bronze”
(satin dark brown powder paint
with fine copper metallic)
installations where the unit is exposed to precipitation or
condensation. EWP products feature foam rubber gaskets
and boots, sealed connections, gel-filled butt connectors, as
well as urethane or thermal plastic potted circuit boards with
internally sealed, field-adjustable trim pots and DIP switches
for easy on-site programming. For more information on
Enhanced Weather Protection, see . DOD 859
DESIGNED, MANUFACTURED AND SUPPORTED IN THE USA
K-1700-3 Series
Handsfree Entry
Phones with Keypads
September 29, 2023
PRODUCT
MANUAL
SECURITY & COMMUNICATION
VIKING
(1) .74”
diameter
Rear View of the Optional
VE-6x7 Surface Mount Box
3.0” 3.3”
3.0”
2.25”
Condensation
Drain Hole
5.64”
6.72” 3.25”
(2) 0.2 x 0.43 slots
(4) 0.38” diameter
4.5”
2.5”
3/4” Conduit
Knockouts
5.5”
Rough-In
Box
(included)
Call
V
I
KI
NG
©
12
ABC
3
DEF
4
G
HI
5
JK L
6
MNO
7
P
RS
8
TU V
9
WXY
0
OPER
#
Mounting Screws: (4) 6-32 X 3/4”
Marine grade 316 stainless steel,
flat head, T-10 Torx security
screws and drive bit (included)
OR
Optional VE-6x7
Surface Mount Box
(not included)
The optional VE-6x7 Surface Mount Box (above) is designed
to be surface mounted to a single gang box, double gang box,
or VE-GNP Gooseneck Pedestal (shown right). For more
information on the VE-6x7 VE-GNPand , see DOD 424.
K-1700-3-EWP
shown with VE-6x7
Surface Mount Box
and VE-GNP
Gooseneck
Pedestal
(not included)
Peel paper liner and adhere gasket to back of
panel, centering over mounting holes.
Caution: For rough surfaces (ie: brick, stucco,
etc.) additional caulking may be required.
2
Features Overview
Earth Ground: To increase surge
protection, loosen the screw labeled
S
HO
(as shown) and fasten a wire with
spade terminal (included) from the
mounting screw to Earth Ground
(grounding rod, water pipe, etc.)
Speaker Volume
Microphone Volume
DIP Switches (see page 3)
Faceplate Gasket: 1/8" thick closed
cell PVC to provide a water-tight seal.
VIKING
Mode l: K-1700- 3
26110 2-1
Seria l No:
REN: 1.0B
XXXXXXXX
Viking Elect ron ics, Inc. (715) 386-8861
1531 Indu stri al S t., H udso n, WI 54016
P/N: DEV:
Co mplie s wit h FCC Part 15 and 68 Reg. No: A H3USA- 32531-T E-E
RoHS
Push Button Switch: Push to initiate
call, push again to disconnect. Solid
316 stainless steel, internally sealed
per IP67.
Speaker Screen: Speaker screen
with 0.018" wide slots to prevent
punctures from paperclips, etc.
Faceplate Material: 14 gauge (0.075
thick) 316 stainless steel. The SS
model has a #4 brushed finish, the BN
model has a powder painted finish.
Speaker: Mylar speaker with rubber
gasket to maintain water-tight seal
and eliminate water deterioration.
Blue LED: Lights blue for “in-use”
indication.
Microphone: An omni-directional
microphone with a water-resistant
cloth for protection.
Call
VIKING
©
Condensation Drain Hole
Mounting Screws: (4) 6-32 X 3/4”
Marine grade 316 stainless steel, flat
head, T-10 Torx security screws and
drive bit (included).
Laser Etched Graphics: For long
lasting easy to read graphics. Copper
metallic on “oil rubbed bronze” model
K-1700-3-BN.
12
ABC
5
JKL
8
TUV
0
OPER
4
GHI
7
PRS
#
3
DEF
6
MNO
9
WXY
Installation
A. Mounting
3
Microphone Volume
(see section B)
Speaker Volume
(see section B)
ON OFF
DIP Switches
(shown in default
positions)
OFFOFF
Rear View of
the K-1700-3
4
3
2
1
8
7
6
5
V
IKIN
G
M
odel
:
K
-1700-3
261102-
1
Serial No
:
REN: 1 .0B
X
XXXXXX
X
V
ikin
g
Electronics, Inc.
(
715
)
386-886
1
1
531 Industri al St., Hudson, WI 5401
6
N
D
EV
:
Complies with FCC Part 15 and 68 R e
g
. No: AH3USA-32531-TE-
E
RoH
S
Programming
A. DIP Switches
Switch 1 Switch 2 Maximum Call Time
OFF OFF Disabled
ON OFF 1 Minute
OFF ON 3 Minutes (default)
ON ON 9 Minutes
Switch 5 Switch 6 Audio Detection
ON ON Normal audio detection
OFF OFF
Increase audio detect sensitivity for
low level lines. Useful in applications
in which voice or busy signals have
trouble breaking over the speaker.
Switch 3 Disconnect on Dial Tone
OFF Off
ON On (default)
Switch 4 VOX Switching Speed
OFF Fast, 0.2 sec. (default)
ON Slow, 0.7 seconds
Switch 7 Auto Answer Position
OFF Automatic answer disabled
ON Automatic answer enabled (default)
Switch 8 Push Button Feature
OFF Connects calls only
ON Connects/disconnects calls (default)
VIKING
Mode l:
K-1700-3
261102- 1
Se rial No :
REN: 1.0B
XXXXXXXX
Viking Electronics, Inc. (715) 386-8 861
1531 Industrial St., Hudson, WI 54016
P/N: DE V:
Complies with FCC Part 15 a nd 68 Re g. No: AH3US A-3253 1-T E-E
RoHS
5.5”
4.04”
6.5”
5.12”
OR
* C.O. Line or Analog
PABX/KSU Station
Spade
Terminal
(included)
*** Earth
Ground
(optional)
Red
(Ring)
Green
(Tip)
Rear View of
the K-1700-3
** Gel-Filled
Connectors
(included)
B. Wiring the K-1700-3
** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge
wire with a maximum insulation of 0.082 inches. Cut off stripped wire ends prior to terminating.
*** Note: To increase surge protection, loosen the PCB
mounting screw labeled (shown right) and fasten a wire
with spade terminal (included) from the mounting screw to
Earth Ground (grounding rod, water pipe, etc.)
* Note: When installing a line powered phone on a low
voltage and/or low loop current phone system extension, a
TBB-1B Talk Battery Booster may be required ( .DOD# 632)
Model DOD# Description
C-500 177 Advanced 2 Door Controller (see page 5)
C-2000B 156 Advanced Door/Gate Controller (see page 6)
C-3000 162 Multi-Tenant Entry System (see page 7)
C-4000 164 Apartment/Office Entry Controller (page 7)
K-1900-3 312 Door Entry Dialer (see page 6)
To Optional Viking Entry Controllers (not included)


Specyfikacje produktu

Marka: Viking
Kategoria: Interkom
Model: K-1700-3

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Viking K-1700-3, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Interkom Viking

Viking

Viking K-1900-712L-EWP Instrukcja

9 Października 2024
Viking

Viking K-1700-3 Instrukcja

9 Października 2024
Viking

Viking E-50-SS Instrukcja

9 Października 2024
Viking

Viking E-50-WH Instrukcja

9 Października 2024
Viking

Viking K-1700-IP-EWP Instrukcja

9 Października 2024
Viking

Viking E-60-BN Instrukcja

9 Października 2024
Viking

Viking E-1600-53-IP Instrukcja

9 Października 2024
Viking

Viking E-60-WH Instrukcja

9 Października 2024
Viking

Viking K-1900-8-IP-EWP Instrukcja

9 Października 2024
Viking

Viking W-2000A Instrukcja

9 Października 2024

Instrukcje Interkom

Najnowsze instrukcje dla Interkom

FlyingVoice

FlyingVoice i86V-01 Instrukcja

9 Października 2024
Valcom

Valcom V-1072B Instrukcja

8 Października 2024
Valcom

Valcom V-1074 Instrukcja

8 Października 2024
Valcom

Valcom V-2972 Instrukcja

8 Października 2024
Valcom

Valcom V-9953 Instrukcja

8 Października 2024
Valcom

Valcom V-TR96 Instrukcja

8 Października 2024
Valcom

Valcom V-5324004 Instrukcja

8 Października 2024
Valcom

Valcom V-9908 Instrukcja

8 Października 2024
Valcom

Valcom V-9923B Instrukcja

8 Października 2024
Valcom

Valcom V-1096 Instrukcja

8 Października 2024