Instrukcja obsługi Velleman HAM982K

Velleman Bezpieczeństwo HAM982K

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Velleman HAM982K (52 stron) w kategorii Bezpieczeństwo. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Pobierz PDF

Strona 1/52

HAM982K 1 VELLEMAN

HAM982K – HOME ALARM STARTER SET

Introduction

Thank you for buying the HAM982K! Please read the manual thoroughly before bringing this device into service.

If the device was damaged in transit, don't install or use it and contact your dealer.

The HAM982K home alarm set comprises:

1. 1 x electronic siren

2. 1 x AC power adapter

3. 1 x PIR detector

4. 5 x magnetic reed switches

5. 1 x panic button

6. 1 x 8-zone alarm control panel

These numbers refer to the chapters below.

1. Electronic Siren

5" horn speaker

Operating voltage 6-12Vdc

Peak output power 7W

Current consumption 600mA

Connection diagram: + =red wire

- = black wire

It is important to know if the N.O. contact is of the positive or the negative type. If it is a positive type, connection

should be made as shown above. If it is a negative type, the switch should be on the black (-) wire.

2. AC Power Adapter

Input voltage 230Vac 50Hz

Output voltage 16.5Vac

Output current 3000mA max.

Rated power factor cos φ 0.96

Protection built-in thermal & current fuse

Dimensions (LxWxH) 76 x 89.5 x 62mm

Weight 1.2kg

Connect the 16.5Vac output terminals to the device's input terminals. Make sure its power consumption does not

exceed the maximum rating of the adapter, and that the connection wires are firmly fixed to the terminals.

Then plug the power plug into a 230Vac mains socket.

The power adapter is for indoor use only.

HAM982K 2 VELLEMAN

1M 2M 3M 4M 5M 6M 7M 8M 9M 10M 11M 12M

42.1░

-42.1

3. PIR Detector

a. Technical Specifications

Detection element low noise dual element pyro sensor

Operating voltage 8-16Vdc ; 12Vdc nominal

Current consumption typical 15mA at 12Vdc

Power-up delay typical 2 minutes with flashing LED indication

Alarm period 2-3s

Alarm output N.C. relay contact with 10Ω in-line resistor. Contact rating: 28Vdc, 0.1A

Walk test with LED alarm indicator

Pulse counting Normal response or 2 pulses within 12 seconds for "harsh" environments

Tamper switch N.C. contact with 10Ω in-line resistor. Contact rating: 12Vdc, 50mA

Operating temperature -10 to +55°C

Humidity max 95% non-condensing

EMC conform to CE standard

Dimensions (HxWxD) 116 x 73.5 x 74mm

b. PCB layout

1. Pyro-sensor (do not touch this sensor!)

2. Walk test & alarm indicator

3. Tamper switch

4. Pulse count jumper ("harsh": for environment with high risk of false detection)

5. LED on/off jumper (on = flashing during start-up, on during operation)

6. Connection terminal block:

Tamper: if a tamper switch is required, connect these terminals to a 24h

normally closed (NC) zone in the alarm control panel. Opening the

housing will trigger a tamper signal.

12Vdc: connect (+) to an 8-16V power source, usually from the alarm control

panel. Connect (-) to the common grounding point.

Alarm: the alarm output relay of the detector. Connect these terminals to a

normally closed (NC) zone in the alarm control panel.

c. Installation

• Install the detector indoors, on a stable surface with a clear view on the protection area.

• Avoid mounting where hot or cold air may blow directly onto the device and where objects

in the detection field may change temperature rapidly (heating or air-conditioning devices).

• Considering the detection angle of the device (see figure on the right), corner mounting is

recommended, at a height of 2 to 3 meters.

Procedure:

1. Open the cover by inserting a small screw driver into the edge of the unit and turning it to release the cover.

2. Remove the PCB by releasing the two fixing screws from the support post - DO NOT DROP THE PCB!

3. Numerous "knockouts" are provided on the back plate. Punch the one which will provide the best cable entry.

4. The two fixing holes on the back of the back plate are for surface mounting. The two fixing holes on the left and

right of the back plate are for corner mounting. Fix the back plate firmly on the wall with the two enclosed screws.

5. Put the PCB back onto the back plate and fix it firmly. Connect the wires to the terminal block.

6. Clip the front cover back in place on the back plate. See to it that the tamper switch is depressed when the front

cover is in place.

HAM982K 3 VELLEMAN

d. Testing

a. Apply 12V DC power and allow 3-5 minutes for the detector to warm up and stabilise before testing.

b. Walk into the protected area at a speed of 1 step per second and watch the LED.

c. The alarm will be triggered when movement is detected. If the pulse count jumper is set to "harsh", 2 detections

need to be made in 12 seconds time for the alarm to be triggered.

d. If proper detection does not occur during the walk tests, relocating or re-aiming the detector may be required.

4. Magnetic Reed Switches

• magnetic switch, standard type

• white ABS

• mounting with screws or double-sided tape

• operating gap: max. 15mm

• dimensions: 51 x 13 x 13mm.

5. Panic button

• NC & NO alarm circuit connection

• screw connectors

• momentary contact (off / on)

• contact rating: 0.5A / 24Vdc max

• colour: ivory

• dimensions: 76 x 22.5 x 16mm

6. Control Panel

a. Front Panel

LEDs ON OFF FLASHING

zone LEDs (8)

zone unsealed – wire is

possibly disconnected. Zone sealed (normal)

•

fast: zone is/was in alarm

•

fast with interval: zone is in alarm memory –

system disarmed

•

slow: zone is isolated

exit/armed alarm armed alarm disarmed exit delay period

•

AC power failure, system runs on battery

(flashing starts 20-30s after power failure)

AC power system on AC power

•

'AC power' & 'battery' flashing alternatively:

system is in power-up delay period

battery battery faulty normal

•

battery is under test

program system in program mode

normal

arm prohibited

system in arm prohibited

mode: indicator is on

during exit delay period

•

System armed (exit delay

expired)

•

System forced to arm

system cannot be armed after exit delay

expired due to faulty zone(s) – see zone

indicators for the faulty zone(s)

Specyfikacje produktu

Marka:	Velleman
Kategoria:	Bezpieczeństwo
Model:	HAM982K

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Velleman HAM982K, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą

Twoje imię*

Twój email*

Napisz tutaj swoje pytanie

Instrukcje Bezpieczeństwo Velleman

Velleman HAM982K Instrukcja

12 Września 2024

Instrukcje Bezpieczeństwo

Najnowsze instrukcje dla Bezpieczeństwo

NetworX NX-595E IP Communication Module Instrukcja

5 Października 2024

Geemarc SOS-PRO 295 Instrukcja

2 Października 2024

One2track Safety Angel Instrukcja

28 Września 2024

Sygonix SY-3851632 Instrukcja

28 Września 2024

Sygonix 1326052 Instrukcja

28 Września 2024

Sygonix 43588A WLAN Camera Instrukcja

28 Września 2024

Sygonix 43176S LAN Camera Instrukcja

28 Września 2024

Sygonix SY-3181234 Instrukcja

28 Września 2024

Sygonix Touch IP65 Instrukcja

28 Września 2024

Sygonix 1882082 Instrukcja

28 Września 2024