Instrukcja obsługi Underwater Kinetics UK4AA eLED Zoom Front Switch

Underwater Kinetics Flesz UK4AA eLED Zoom Front Switch

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Underwater Kinetics UK4AA eLED Zoom Front Switch (1 stron) w kategorii Flesz. Ta instrukcja była pomocna dla 5 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/1
Limited Lifetime Warranty
Battery Installation
To install batteries, hold the
case in the position shown.
Drop the batteries one by one
into the case in the order
shown. Make sure that the (+)
end of the battery is down for 1
and 2 and up for batteries 3 and
4. Insert the lens, spring and
lamp module into the bezel and
screw it onto the case.
ON/OFF
To operate the UK4AA push in
on the black rubber switch to
turn the light on and off. For
momentary lighting press the
switch half-way in.
HIGH/LOW Power
Battery Life Extension
Battery life can be extended by
switching the UK4AA Zoom
from high to low power. In order
to switch to low power, the light
must be ON. By quickly pressing
the switch twice, brightness will
go from high to low. Repeating
the process will switch the light
back to high power.
Changing Beam Angle
With Projection Optics
The beam angle of the UK4AA
Zoom can be adjusted by rotat-
ing the bezel. When the bezel
is screwed all the way down,
beam coverage is at maximum.
Unscrewing the bezel for up to
one full turn will reduce the
beam angle from about 21°to
13°or by 40%.
4AA eLED® Zoom Light
Model Number: UK4AA-AS2ZM
Thank you for purchasing
this UK all environment work
and outdoor light! It is tough
enough for use in rain, snow,
smoke, dust or hazardous
locations (see listing). The
high intensity adjustable
beam eLED lamp delivers
constant brightness over
most of the battery life. With
battery saving mode, battery
life is more than doubled.
CL I, DIV 2, GP A, B, C,
D, CL II, DIV 2 GP F, G
CL III, DIV 2 T4
Care and Maintenance
Keep area around the
O-ring clean.
If the light floods, empty
it immediately, rinse with
fresh water and dry com
pletely before
reassembly.
Replace the
reflector/lamp, which
contains a hydrogen
absorbing catalyst, if it
gets wet.
Do not store batteries in
the light for long periods
of time; they may leak
and damage the light.
Bezel
Lens
Spring
14846
eLED Lamp Module
4 Alkaline AA-cell batteries
O-Ring
Switch
UK4AA eLED ZOOM Case
Vent
2
1
3
4
©2010 Underwater Kinetics P/N: 400881
Battery Insertion
The UK4AA will
not light if the bat-
teries are not
inserted with the
polarity as shown.
Beam Brightness
By quickly pressing
the switch twice,
brightness will go
from high to low or
low to high.
O-Ring Seal
Lightly lubricate the O-ring with
silicone grease. Do not use tools
to remove the O-ring.
Pressure Equalizing Vent
Air and gas from battery leak-
age can pass freely in and out
of the UK4AA through a vent in
the rear of the light. Do not
allow dirt or grease to accumu-
late on the vent or it will not
operate properly.
Instructions & Important Information
Underwater Kinetics products
are engineered for maximum
performance and durability. All
products carry a Limited
Lifetime Warranty to the
original retail purchaser
to be free from defective
material and workmanship
under normal and intended use.
In addition, the Underwater
Kinetics Limited Warranty
covers materials used in its
products to the original
purchaser, from the date of
purchase, as follows: plastics
for 10 years; rubber for 3 years,
LED and electronics for 1 year,
rechargeable batteries for 90
days.
In the event the original retail
purchaser detects a defect in
the material or workmanship,
the product along with proof of
purchase date should be
returned to an authorized
Underwater Kinetics dealer or
directly to Underwater Kinetics
with the postage prepaid.
Underwater Kinetics agrees to
repair or replace at Underwa-
ter Kinetics' sole discretion any
product found to be defective
in material or workmanship
within the time period specified
above. For the complete
Limited Lifetime Warranty write
to Underwater Kinetics or go to
the web site
www.underwaterkinetics.com.
Address all correspondence
and returns to:
Underwater Kinetics
13400 Danielson Street
Poway, CA 92064
Batteries can vent hydrogen
gas and possibly cause an
explosion if they are (1)
installed without the proper
polarity, (2) not the same
type, brand name and age
or (3) completely
discharged.
Load batteries according
to the diagram.
Discard all batteries as
soon as they are drained
or no longer produce
light.
Do not mix batteries of
different type, brand or
age.
Certifications
This equipment is suitable for
use in Class I, Division 2
Groups A, B, C, D: Class II,
Division 2, Group F, G; Class
III Division 2, or Non-
Hazardous Locations Only.
Use only with 14846 Lamp
and 4 Duracell
MN1500/PC1500, Energizer
E91/EN91 or Rayovac
AL-AA/815 1.5 V size AA
Alkaline batteries.
Explosion Hazard
Do Not disconnect
Equipment Unless Power
Has Been Seitched Off Or
The Area Is Known To Be
Non-Hazardous
Explosion Hazard
Substitution of Components
May Impair Suitability For
Class I, Division 2.


Specyfikacje produktu

Marka: Underwater Kinetics
Kategoria: Flesz
Model: UK4AA eLED Zoom Front Switch

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Underwater Kinetics UK4AA eLED Zoom Front Switch, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Flesz Underwater Kinetics

Instrukcje Flesz

Najnowsze instrukcje dla Flesz

Ledlenser

Ledlenser P9R Core LEP Instrukcja

15 Października 2024
LED Lenser

LED Lenser P5R Instrukcja

11 Października 2024
Brennenstuhl

Brennenstuhl TL 1201 AF Instrukcja

9 Października 2024
Brennenstuhl

Brennenstuhl TL 601 AF Instrukcja

9 Października 2024
Klein Tools

Klein Tools KHH56308 Instrukcja

9 Października 2024
Brennenstuhl

Brennenstuhl HL 400 AC Instrukcja

9 Października 2024
Nitecore

Nitecore MH40 Pro Instrukcja

8 Października 2024
Nitecore

Nitecore HU2000 Instrukcja

8 Października 2024
AccuLux

AccuLux UniLux PRO Instrukcja

8 Października 2024
AccuLux

AccuLux SL6 LED Instrukcja

8 Października 2024