Instrukcja obsługi Tommee Tippee Digital Ear thermometer
Tommee Tippee
Produkty dla dzieci
Digital Ear thermometer
Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Tommee Tippee Digital Ear thermometer (3 stron) w kategorii Produkty dla dzieci. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek
Strona 1/3
On/Mem
C
R
2
0
3
2
1 2
HYGIENE
COVER
CONNECTION
RING
34
5
°C
The LCD screen will light up automatically after pressing the scan button, and will automatically turn
off after 5 seconds.
8. The temperature will show clearly on the LCD display.
9. To power off, hold down the ‘On/Mem’ button for approximately 5 seconds, until the LCD screen
shows ‘o’. The thermometer will automatically shut down after 1 minute if it is not turned off,
prolonging the battery life.
FEVER ALARM
If the thermometer detects a body temperature ≥37.5°C (99.5°F), one long beep will sound followed
by three short beeps to warn the user of potential fever.
SWITCHING BETWEEN FAHRENHEIT (°F) AND CELSIUS (°C)
1. In ‘Power off’ mode, press and hold the ‘Scan’ button.
2. Then press the ‘On/Mem’ button for 3 seconds whilst still holding the scan button. The ‘°C’ will
change to ‘°F’. You can use the same process to change from ’°F’ back to ‘°C’.
MEMORY FUNCTION
1. Press the ‘On/Mem’ button again to see the last temperature stored.
The thermometer will automatically save the last reading into the memory, if it is within the
temperature range of 34°C to 42.2 °C (93.2 °F to 108.0°F).
CLEANING AND STORAGE
The probe is the most delicate part of the thermometer. When cleaning the lens handle with care to
avoid damage. If device is accidentally used without hygiene cover, clean the probe as follows:
1. Use a cotton swab (Alcohol 70% concentration) to clean the lens found inside the probe.
2. Allow the probe to fully dry for at least 1 minute.
The thermometer should be stored at temperature between -20°C to +50°C.
Keep the unit dry and away from any liquids and out of direct sunlight.
The probe should not be submerged in any liquids.
If the thermometer is used according to the instructions, periodic re-adjustment is not required.
CHANGING THE BATTERY
Keep the battery away from children.
This device is supplied with one lithium cell battery (CR2032).
1. Unscrew battery cover.
2. Flip the battery out with a small screw driver.
3. Insert the new battery under the metal hook on the left side and press the right side of the
battery down firmly. See diagram 5.
4. Replace the battery cover.
The positive (+) side up and the negative (-) side pointed down.
SPECIFICATIONS
Temperature measurement range: 34-42.2°C (93.2-108°F)
Operating temperature range: 10-40°C (50-104°F), RH<85%
Storage temperature range: -20-+50°C, RH≤85%
Transportation temperature: < than 70°C, RH≤95%,
Atmospheric pressure: 800~1013 hPa
Enclosure Rating: IP22
Dimensions: 149.1 x 42.5 x 54.9 mm
Weight: 79.7 grams including battery
Battery life: around 3,000 readings. Enable normal use: 1 year
Expected Service Life: 4 years
Complies with ASTM E1965-98, EN12470-5:2003 Clinical thermometers-Part 5: Performance of infra-red
ear thermometers (with maximum device), IEC/EN60601-1-2(EMC),IEC/EN60601-1(Safety) standards.
Accuracy: +/-0.2 °C (0.4 °F) in a temperature range of 35.5-42°C (95.9-107.6°F). Accuracy of +/-0.3 °C
(0.5 °F) for other temperature ranges.
This thermometer converts the ear temperature to display its “oral equivalent.” (according to the result
of the clinical evaluation)
INSTRUCTIONS FOR USE
Before first use, pull to remove the tab from the battery cover.
INSTALLING THE HYGIENE COVER
WARNING: Choking from swallowing probe covers and connection ring by children or pets is possible,
please keep the probe covers and connection ring at places where children and pets can’t reach.
1. Gently twist the probe cap to remove. Always use a new and undamaged hygiene cover before
each reading. Ensure the ear canal is clean.
2. Place a new hygiene cover into the connection ring. See diagram 1.
3. Insert the thermometer probe into the centre of the hygiene cover and connection ring.
See diagram 2.
4. Push until it is secure. If the hygiene cover did not connect firmly, this icon will be flashing
on the LCD screen. Remove the hygiene cover and re-install.
Correct installation of the hygiene cover ensures accurate readings.
5. Press ‘On/Mem’ button. The thermometer is ready for use when the ear icon stops flashing
and two short beeps have sounded.
6. Gently pull the baby’s ear back, straightening the ear canal. Position the probe snugly into the
ear canal, ensuring an accurate reading. See diagram 3 and 4.
7. To measure the ear temperature, press the ‘Scan’ button until there is a long beep.
GB
LCD
ON/MEMORY
BUTTON
FRONT COVER
BATTERY COVER
SCAN
BUTTON
REAR COVER
WORLDWIDE
SMALLEST PROBE
DIAMETER
=5.9MM
HYGIENE
COVER
DETECTOR
HYGIENE COVER
PROBE
LENS
On/Mem
GUIDANCE AND MANUFACTURER’S DECLARATION – ELECTROMAGNETIC IMMUNITY
The Digital Ear Thermometer is intended for use in the electromagnetic environment specified
below. The customer or the user of the Digital Ear Thermometer. should assure that it is used in
such an environment.
Immunity test
Electrostatic
discharge (ESD)
IEC 61000-4-2
Electrical fast
transient/burst
IEC 61000-4-4
Surge
IEC 61000-4-5
interruptions
and voltage
variations on
power supply
input lines
IEC 61000-4-11
Power
frequency
(50/60 Hz)
magnetic field
IEC 61000-4-8
Compliance
level
6 kV contact
8 kV air
Not
applicable
Not
applicable
Not
applicable
3 A/m
Electromagnetic environment –
guidance
Floors should be wood, concrete
or ceramic tile. If floors are
covered with synthetic material,
the relative humidity should be at
least 30 %.
Mains power quality should be
that of a typical commercial or
hospital environment.
Mains power quality should be
that of a typical commercial or
hospital environment.
Mains power quality should be
that of a typical commercial or
hospital environment. If the user
of the Digital Ear Thermometer
requires continued operation
during power mains
interruptions, it is recommended
that the Digital Ear Thermometer
be powered from an
uninterruptible power supply or a
battery.
Power frequency magnetic fields
should be at levels characteristic
of a typical location in a typical
commercial or hospital
environment.
IEC 60601 test level
6 kV contact
8 kV air
2 kV for power supply
lines
1 kV for input/output
lines
1 kV line(s) to line(s)
2 kV line(s) to earth
<5 % UT
(>95 % dip in UT)
for 0,5 cycle
40 % UT
(60 % dip in UT)
for 5 cycles
70 % UT
(30 % dip in UT)
for 25 cycles
<5 % UT
(>95 % dip in UT)
for 5 sec
3 A/m
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is
affected by absorption and reflection from structures, objects and people.
a. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless)
telephones and land mobile radios, amateur radio, AM and FM radio broadcast and TV
broadcast cannot be predicted theoretically with accuracy. To assess the electromagnetic
environment due to fixed RF transmitters, an electromagnetic site survey should be considered.
If the measured field strength in the location in which the Digital Ear Thermometer is used
exceeds the applicable RF compliance level above, the Digital Ear Thermometer should be
observed to verify normal operation. If abnormal performance is observed, additional
measures may be necessary, such as reorienting or relocating the Digital Ear Thermometer.
b. Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
RECOMMENDED SEPARATION DISTANCES BETWEEN PORTABLE AND MOBILE RF
(RADIO FREQUENCY) COMMUNICATIONS EQUIPMENT AND THE ME EQUIPMENT
OR ME SYSTEM
The Digital Ear Thermometer is intended for use in an electromagnetic environment in which
radiated RF disturbances are controlled. The customer or the user of the Digital Ear Thermometer can
help prevent electromagnetic interference by maintaining a minimum distance between portable
and mobile RF communications equipment (transmitters) and the Digital Ear Thermometer as
recommended below, according to the maximum output power of the communications equipment.
Rated maximum output
power of transmitter
W
For transmitters rated at a maximum output power not listed above, the recommended separation
distance d in meters (m) can be estimated using the equation applicable to the frequency of the
transmitter, where P is the maximum output power rating of the transmitter in watts (W)
according to the transmitter manufacturer.
NOTE 1 At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2 These guidelines may not apply in all situations. Electromagnetic propagation is affected
by absorption and reflection from structures, objects and people.
80 MHz to 800 MHz
d = 1,2 √P
0,12
0,38
1,2
3,8
12
800 MHz to 2,5 GHz
d = 2,3 √P
0,23
0,73
2,3
7,3
23
150 kHz to 80 MHz
d = 1,2 √P
0,12
0,38
1,2
3,8
12
Separation distance according to frequency of transmitter
m
0,01
0,1
1
10
100
NOTE UT is the a.c. mains voltage prior to application of the test level.
TROUBLESHOOTING
It is recommended that you measure 3 times in the same ear. If the 3 measurements are different,
select the highest temperature.
There is no gender and age limitation for using infrared thermometers.
Clinical repeatability 0.18°C newborn to 1 year old, 0.17°C 1-5years old, 0.15°C 5years+
Holding the thermometer too long may cause a higher ambient temperature reading. This could
make the body temperature measurement lower than usual.
This product comes with a 12 month warranty. Manufacture Date：as the serial number (please open
the battery cover, it is shown on the inside of the device.) Ex.SN:E912A000001, the first “E” is External,
the second number “9” is the manufacture year 2009, the third and the fourth number “12” is the
manufacture month, the remaining figures are the serial number.
BF type applied part
SYMBOL DESCRIPTIONS
GUIDANCE AND MANUFACTURER’S DECLARATION – ELECTROMAGNETIC EMISSIONS
PROBLEM
Device stabilization in process.
Battery is low and no more
measurements are possible.
Measurement before device stabilization.
The device showing a rapid ambient
temperature change.
The ambient temperature is not within
the range between 10 °C and 40 °C (50 °F
~104 °F).
Error 5~9, the system is not functioning
properly.
Temperature taken is higher than 42.2 °C
(108.0 °F).
Temperature taken is lower than 34 °C
(93.2 °F).
Device can not be powered on to the
ready stage.
SOLUTION
Wait until stops flashing.
Replace the battery.
Wait until stops flashing.
Allow the thermometer to rest in a room for
at least 30 minutes at room temperature:
10
°
C and 40
°
C (50
°
F ~104
°
F).
Allow the thermometer to rest in a
room at least 30 minutes at room
temperature: 10 °C and 40 °C (50 °F ~104 °F).
Unload the battery, wait for 1 minute
and repower it.
Check the integrity of the hygiene cover
and take a new temperature measurement.
Make sure the hygiene cover is clean
and take a new temperature measurement.
Insert a new battery.
The Digital Ear Thermometer is intended for use in the electromagnetic environment specified
below. The customer or the user of the Digital Ear Thermometer should assure that it is used in
such an environment.
Emissions test
RF emissions
CISPR 11
RF emissions
CISPR 11
Harmonic emissions
IEC 61000-3-2
Voltage fluctuations/
flicker emissions
IEC 61000-3-3
Electromagnetic environment – guidance
The Digital Ear Thermometer uses RF (Radio
Frequency) energy only for its internal function.
Therefore, its RF emissions are very low and are not
likely to cause any interference in nearby electronic
equipment.
The Digital Ear Thermometer is suitable for use in
all establishments, including domestic
establishments and those directly connected to
the public low-voltage power supply network that
supplies buildings used for domestic purposes.
Compliance
Group 1
Class B
Not applicable
Not applicable
GUIDANCE AND MANUFACTURER’S DECLARATION – ELECTROMAGNETIC IMMUNITY
The Digital Ear Thermometer is intended for use in the electromagnetic environment specified
below. The customer or the user of the Digital Ear Thermometer should assure that it is used in
such an environment.
Immunity test
Conducted RF
IEC 61000-4-6
Radiated RF
IEC 61000-4-3
Compliance
level
Not applicable
3 V/m
Electromagnetic environment – guidance
Portable and mobile RF communications
equipment should be used no closer to any
part of the Digital Ear Thermometer, including
cables, than the recommended separation
distance calculated from the equation
applicable to the frequency of the transmitter.
Recommended separation distance
d = 1,2
√P
d = 1,2 √P 80 MHz to 800 MHz
d = 2,3 √P 800 MHz to 2,5 GHz
where P is the maximum output power
rating of the transmitter in watts (W)
according to the transmitter manufacturer
and d is the recommended separation
distance in meters (m).
Field strengths from fixed RF transmitters, as
determined by an electromagnetic site
survey, a should be less than the
compliance level in each frequency range b.
Interference may occur in the vicinity of
equipment marked with the following
symbol:
IEC 60601
test level
3 Vrms
150 kHz to
80 MHz
3 V/m
80 MHz to
2,5 GHz
ERROR
MESSAGE
EC REP
The CE mark and Notified
Body Registration
Numbers, the
requirement of Annex II
from Medical Device
Directive 93/42/EEC are
met.
Please read the
instructions for use
BF type applied part
IP22 Classification for water ingress and particulate matter.
Indicates this device is subject to the
Waste Electrical and Electronic
Equipment Directive in the European
Union. To protect the environment,
dispose of useless device at appropriate
collection sites according to national or
local regulations.
Paper Recycling
Battery Recycling
Manufacturer
Authorized
representative in
the European
community
WEE/JC0045SY 2
0120 Do not reuse
Caution
Specyfikacje produktu
| Marka: | Tommee Tippee |
| Kategoria: | Produkty dla dzieci |
| Model: | Digital Ear thermometer |
Potrzebujesz pomocy?
Jeśli potrzebujesz pomocy z Tommee Tippee Digital Ear thermometer, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą
Instrukcje Produkty dla dzieci Tommee Tippee
13 Września 2024
5 Lipca 2024
Instrukcje Produkty dla dzieci
- Produkty dla dzieci Severin
- Produkty dla dzieci Joie
- Produkty dla dzieci Angelcare
- Produkty dla dzieci Medela
- Produkty dla dzieci Chicco
- Produkty dla dzieci Moulinex
- Produkty dla dzieci Nuna
- Produkty dla dzieci Melissa
- Produkty dla dzieci Foppapedretti
- Produkty dla dzieci Graco
- Produkty dla dzieci Safety 1st
- Produkty dla dzieci Hauck
- Produkty dla dzieci Weber
- Produkty dla dzieci BeSafe
- Produkty dla dzieci Babymoov
- Produkty dla dzieci Peg Perego
- Produkty dla dzieci Kinderkraft
- Produkty dla dzieci Terraillon
- Produkty dla dzieci Jane
- Produkty dla dzieci Orion
- Produkty dla dzieci Bebe Confort
- Produkty dla dzieci Alecto
- Produkty dla dzieci Reer
- Produkty dla dzieci Dualit
- Produkty dla dzieci Lorelli
- Produkty dla dzieci Kidsmill
- Produkty dla dzieci Inglesina
- Produkty dla dzieci Ergobaby
- Produkty dla dzieci Joycare
- Produkty dla dzieci Pericles
- Produkty dla dzieci Laica
- Produkty dla dzieci Brevi
- Produkty dla dzieci Switel
- Produkty dla dzieci Topmark
- Produkty dla dzieci Bopita
- Produkty dla dzieci Duux
- Produkty dla dzieci Nova
- Produkty dla dzieci Luvion
- Produkty dla dzieci Joovy
- Produkty dla dzieci Beaba
- Produkty dla dzieci Maclaren
- Produkty dla dzieci Giordani
- Produkty dla dzieci Badabulle
- Produkty dla dzieci Hartig Helling
- Produkty dla dzieci Fillikid
- Produkty dla dzieci Pabobo
- Produkty dla dzieci Bambino Mio
- Produkty dla dzieci Quax
- Produkty dla dzieci Pigeon
- Produkty dla dzieci Tommee
- Produkty dla dzieci Seca
- Produkty dla dzieci Bhoop
- Produkty dla dzieci Dreambee
Najnowsze instrukcje dla Produkty dla dzieci
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024
28 Września 2024