Instrukcja obsługi Teledex Opal 1003

Teledex telefon Opal 1003

Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Teledex Opal 1003 (7 stron) w kategorii telefon. Ta instrukcja była pomocna dla 3 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/7
OWNERS
MANUAL
OPAL 1003
1005
1010
The Teledex one-line
telephones specifically
designed for the international
hospitality industry.
INCLUDED IN YOUR PACKAGE
Handset
Base Unit
Coiled Handset Cord
Line Cord
Clear Plastic Overlay
User Guide
CONNECTING THE OPAL TELEPHONE
1. Located on the left side of the Opal (as the phone is facing you) is a modular jack. Insert one end of the coiled
handset cord into this jack (you should hear the coil cord click when properly inserted).
2. Insert the other end of the coiled handset cord into the modular jack on the handset.
3. Turn the telephone so the back panel is facing you. Insert either end of the line cord into the jack on the back of
the telephone labeled LINE.
4. Insert the other end of the line cord into a telephone wall outlet jack.
5. Once your telephone is connected, remove the plastic overlay and place the paper faceplate over the keys.
Replace the plastic overlay by hooking the tabs on the overlay into the recessed slots located on both sides. The
overlay is easiest to insert when; the left or right side tabs are inserted first, and the middle of the overlay is
slightly bowed to allow for insertion of the other tabs.
PLACING A CALL
1. Lift the handset.
2. Listen for dial tone. Dial the desired number, or press an AUTO DIAL key to automatically dial a number.
3. To end the call, hang up by placing the handset back in the cradle.
RECEIVING A CALL
An audible ring and flickering red message waiting light will indicate an inbound call.
1. Lift the handset. The Opal will engage the ringing line.
2. To end the call hang up the handset.
ADJUSTING THE RING VOLUME
Locate the adjustment control on the back of the telephone labeled RINGER LOW/HI. Slide the switch to the
desired LOW or HI ring volume.
REDIAL
TO REDIAL THE LAST TELEPHONE NUMBER DIALED:
1. Lift the handset from the cradle.
2. Press the REDIAL key.
ADJUSTING THE HANDSET VOLUME
The HANDSET VOLUME key has three levels. When the handset is first lifted, the handset volume is NORMAL.
Locate the HANDSET VOLUME key below the keypad. Press the key once and the volume level will increase
one level (to MEDIUM volume). Press the key once more and the volume level will increase an additional level
(to HIGH volume). To return the handset volume to NORMAL , press the handset volume key again.
The handset volume will always return to NORMAL when the handset is replaced in the cradle.
FLASH KEY
Pressing the FLASH key initiates a 600ms hookflash. Typical usage is to access PBX features like call waiting.
AUTO DIAL KEYS
The Opal has programmable AUTO DIAL keys. These keys can be programmed to automatically dial telephone
numbers, or activate telephone system features.
PROGRAMMING AUTO DIAL KEYS:
The telephone must be connected to a telephone line.
1. Lift the handset from the cradle.
2. Press the recessed STORE key and release it. (Please see diagram on the next page).
3. Enter the telephone number including PAUSE* as required. The sequence can be up to 15 digits.
4. Press the AUTO DIAL key where the number is to be stored.
5. Place the handset back in the cradle.
*A 3.6 second pause is entered in a dialing sequence by pressing the REDIAL key for each PAUSE required.
CONVERTING FROM DESK TO WALL MOUNT
The Opal Telephone can be changed for wall mounting applications. The conversion is easiest when the handset
and line cords are not connected.
1. Located on the top of the telephone above the speaker grill is the wall/desk mount clip. Remove this clip by
firmly pushing upward (towards the hookswitch).
2. Flip the clip over (top to bottom) so that the protruding edge is towards the top of the phone. This edge will
hold the handset.
3. Turn the Opal over so the bottom is up facing you. Place the Opal on a nonabrasive surface to prevent scratch-
ing.
4. Locate and remove the mounting bracket, firmly push back and pull up to remove two of the four retaining tabs.
5. Rotate the mounting bracket 180 degrees clockwise so that the mounting eyelet on the bracket is facing in the
same direction as the other mounting eyelet located on the bottom of the telephone.
6. Insert the top two retaining tabs of the mounting brackets into the mounting bracket slots (located near the
middle of the telephone). Then firmly push down to insert the retaining tabs on the opposite side of the mounting
bracket.
7. Connect a short modular line cord into the jack on the back of the phone (labeled LINE). Route the line cord
thought the line cord channel. Connect the other end of line cord to the phone jack on the wall mounting plate.
8. Turn the telephone over, and slide the Opal down onto the mounting posts in downward direction. Both eyelets
should line up with the mounting posts.
9. Complete the wall mounting by installing the handset and handset cord.


Specyfikacje produktu

Marka: Teledex
Kategoria: telefon
Model: Opal 1003

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Teledex Opal 1003, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje telefon Teledex

Instrukcje telefon

Najnowsze instrukcje dla telefon

Profoon

Profoon PDX-7020 Instrukcja

14 Października 2024
Profoon

Profoon PDX-100 Instrukcja

14 Października 2024
Uniden

Uniden XS 1415 Instrukcja

13 Października 2024
Uniden

Uniden XDECT 6105BTU Instrukcja

10 Października 2024
Yealink

Yealink MP56 E2 Instrukcja

9 Października 2024
Yealink

Yealink MP54 E2 Instrukcja

9 Października 2024
Yealink

Yealink MP58-WH E2 Instrukcja

9 Października 2024
Yealink

Yealink MP52 E2 Instrukcja

9 Października 2024
VXi

VXi D200 Dialpad Instrukcja

9 Października 2024
Lewitt

Lewitt LCT 240 Instrukcja

9 Października 2024