Instrukcja obsługi Technika THM2650NG


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla Technika THM2650NG (15 stron) w kategorii Kotły i bojlery. Ta instrukcja była pomocna dla 4 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/15
WaterMark
GMK1017 7 WMKA22451 5339
THM2050NG/THM2070NG
THM2650NG/THM2670NG
THM2050LPG/THM2070LPG
THM2650LPG/THM2670LPG
Gas Water Heater
2
WARNING
1.1 INSTALLATION NOTES
1.2 SERVICE NOTES
1.3 PLUMBING NOTES
The installation must be done in accordance with the information supplied in this manual. All other
relevant national, state and local regulations must also be adhered to including (but are not limited to):
Australian Standard AS3500.1 – Water Services.
Australian Standard AS3500.4 – Heated Water Services.
Australian Standard AS3000 – Electrical Installation.
Australian Standard AS/NZS5601 – Gas Appliance Installation.
Local Water, Gas & Electrical Authority Regulations.
Municipal Building Codes including local OH&S requirements.
Installation and service must be performed by a licensed professional (for example, a
licensed plumber or gas fitter).
Water pipe size is nominal 15mm from hot water outlet to the first tap / outlet.
Gas pipe size is nominal 20mm.
!
When connecting the hot water supply to the fixtures of the property a minimum of two (2) metres
of pipework must be used between the outlet of the water heater and the first tap / outlet.
(See Diagram on following page).
The hot water line should be insulated with Armaflex or similar pipe insulation.
When the installation is completed the temperature is to be tested at the taps to confirm the
water temperature does not exceed the required 50 setting.
1. IMPORTANT NOTES
This manual has been prepared for the relevant licensed professionals of the equipment.
Please keep it in a safe place for future reference.
Maintenance and fault-finding must be done in accordance with these instructions and the
applicable regulations listed above.
PLEASE NOTE THM2050 and THM2650 model is supplied factory pre-set at Nominal 50°C maximum
outlet water temperature(dip switch preset temperature as 48°C ) to comply with the requirements of
AS 3498 Clause 7.2.1.
The THM2050 and THM2650 unit DOES NOT REQUIRE a temperature control device to be installed.
Please follow all the instructions in the Installation Guide and the following additional instructions for
the water heater outlet connection.
PLEASE NOTE THM2070 and THM2670 models are supplied with the Maximum outlet temperature
of 70°C and the factory pre-set is 55°C outlet water temperature to comply with the requirements of
AS 3498 Clause 7.2.2.
The THM2070 and THM2670 unit REQUIRES a temperature control device to be installed.


Specyfikacje produktu

Marka: Technika
Kategoria: Kotły i bojlery
Model: THM2650NG

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z Technika THM2650NG, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Kotły i bojlery Technika

Technika

Technika THM2650NG Instrukcja

15 Września 2024

Instrukcje Kotły i bojlery

Najnowsze instrukcje dla Kotły i bojlery

Sencor

Sencor SWK 7706GD Instrukcja

14 Października 2024
Hotpoint

Hotpoint HE30S01SAG Instrukcja

13 Października 2024
Nibe

Nibe VPA 300/200 E Instrukcja

9 Października 2024
Noritz

Noritz NC199OD Instrukcja

9 Października 2024
Nibe

Nibe Melite 120 Instrukcja

8 Października 2024
Nibe

Nibe VPB 500-1000 Instrukcja

8 Października 2024
Elba

Elba EWH-E3881(SW) Instrukcja

8 Października 2024
Elba

Elba EWH-E3885DC(SG) Instrukcja

8 Października 2024
Elba

Elba EWH-G3661(MB) Instrukcja

8 Października 2024