Instrukcja obsługi System Sensor OSI-R-SS


Przeczytaj poniżej 📖 instrukcję obsługi w języku polskim dla System Sensor OSI-R-SS (48 stron) w kategorii Detektor dymu. Ta instrukcja była pomocna dla 2 osób i została oceniona przez 2 użytkowników na średnio 4.5 gwiazdek

Strona 1/48
OSI-R-SS, OSI-RA-SS
Single-ended Reflected
Type Projected Imaging
Beam Smoke Detector -
Conventional
Installation Guide
October 2018
Document No.: E56-6572-001 (33777_01)
OSI-R by System Sensor OSI-R-SS, OSI-RA-SS Installation Guide
E56-6572-001 | October 2018 i
Intellectual Property and Copyright
This document includes registered and unregistered trademarks. All trademarks displayed are the trademarks of
their respective owners. Your use of this document does not constitute or create a license or any other right to use
the name and/or trademark and/or label.
This document is subject to copyright owned by HPSS (Honeywell Products & Solutions Sarl). You agree not to
copy, communicate to the public, adapt, distribute, transfer, sell, modify or publish any contents of this document
without the express prior written consent of System Sensor.
Disclaimer
The contents of this document is provided on an “as is” basis. No representation or warranty (either express or
implied) is made as to the completeness, accuracy or reliability of the contents of this document. The manufacturer
reserves the right to change designs or specifications without obligation and without further notice. Except as
otherwise provided, all warranties, express or implied, including without limitation any implied warranties of
merchantability and fitness for a particular purpose are expressly excluded.
General Warning
This product must only be installed, configured and used strictly in accordance with the General Terms and
Conditions, User Manual and product documents available from System Sensor. All proper health and safety
precautions must be taken during the installation, commissioning and maintenance of the product. The system
should not be connected to a power source until all the components have been installed. Proper safety precautions
must be taken during tests and maintenance of the products when these are still connected to the power source.
Failure to do so or tampering with the electronics inside the products can result in an electric shock causing injury
or death and may cause equipment damage. System Sensor is not responsible and cannot be held accountable for
any liability that may arise due to improper use of the equipment and/or failure to take proper precautions.
Critical Product Security
Open Source Software
This product contains open source software provided by third parties. It does not necessarily use all of the third
party software components. Go to http://www.security.honeywell.com/opensource/ for a detailed list of the third party
software used and the associated open source license agreement(s).
Firmware Updates
This device supports firmware upgrades via its USB port. When performing a firmware update the new firmware
update file should be downloaded from the System Sensor website and saved to a USB memory device that has
had all of its content removed.
Approved firmware version: S03-0089-000.
Device and System Security
Before installing this product ensure that the two security seals on the packaging are unbroken and the product has
not been tampered with since leaving the factory. Do not install this product if there are any indications of
tampering. If there are any signs of tampering the product should be returned to the point of purchase.
It is the responsibility of the system owner to ensure that all system components, i.e. devices, panels, wiring etc., are
adequately protected to avoid tampering of the system that could result in information disclosure, spoofing, and
integrity violation.
This device utilizes Secure Boot to validate the device’s software using a hardware root of trust and cryptographic
signatures. If the software cannot be validated the device will generate a trouble condition in the system.
Liability
You agree to install, configure and use the products strictly in accordance with the User Manual and product
documents available from System Sensor.
System Sensor is not liable to you or any other person for incidental, indirect, or consequential loss, expense or
damages of any kind including without limitation, loss of business, loss of profits or loss of data arising out of your
use of the products. Without limiting this general disclaimer the following specific warnings and disclaimers also
apply:
Fitness for Purpose
You agree that you have been provided with a reasonable opportunity to appraise the products and have made
your own independent assessment of the fitness or suitability of the products for your purpose. You acknowledge


Specyfikacje produktu

Marka: System Sensor
Kategoria: Detektor dymu
Model: OSI-R-SS

Potrzebujesz pomocy?

Jeśli potrzebujesz pomocy z System Sensor OSI-R-SS, zadaj pytanie poniżej, a inni użytkownicy Ci odpowiedzą




Instrukcje Detektor dymu System Sensor

Instrukcje Detektor dymu

Najnowsze instrukcje dla Detektor dymu

First Alert

First Alert HD6135FB Instrukcja

14 Października 2024
Kidde

Kidde 3SFWR Instrukcja

9 Października 2024
Kidde

Kidde KF30R Instrukcja

9 Października 2024
Kidde

Kidde P4010ACS-WCA Instrukcja

9 Października 2024
Kidde

Kidde P4010DCSCO-WCA Instrukcja

9 Października 2024
Kidde

Kidde i12020CA Instrukcja

9 Października 2024
Kidde

Kidde i12040CA Instrukcja

9 Października 2024
Kidde

Kidde KF20R Instrukcja

9 Października 2024
Kidde

Kidde CP9000CA Instrukcja

9 Października 2024
Kidde

Kidde Pi2010CA Instrukcja

9 Października 2024